HD 400 3M S2-1992 Hand-Held Motor Operated Tools Part II Particular Specifications Section M Planers《手提式电动工具 第2部分 特殊规范 第M节 刨床》.pdf

《HD 400 3M S2-1992 Hand-Held Motor Operated Tools Part II Particular Specifications Section M Planers《手提式电动工具 第2部分 特殊规范 第M节 刨床》.pdf》由会员分享，可在线阅读，更多相关《HD 400 3M S2-1992 Hand-Held Motor Operated Tools Part II Particular Specifications Section M Planers《手提式电动工具 第2部分 特殊规范 第M节 刨床》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、. CENELEC INFORMATION SHEET Issue 1 1992-02-06 Rue de Stassart. 35 - 1050 Bruxelles Tl.: (+ 32 2) 519.68.71 - Fax: (+ 32 2) 518.69.19 Teletex 206 2210087 - CENCEL - TX 172210097 HO COO. 3M s2 February 1992 I I Hand-held motor operated tools Part II: Particular specifications Section M: Planers Outil

2、s portatifs main moteur Partie II: Rgles particulires Section H : Rabots Handgefhrte Elektrowerkzeuge Teil II: Besondere Bestimungen Hauptabschnitt H: Hobel RO: CEE 20-2M:1977 Related to Directive: 73123iEEC This Harmonization Document consists of the following: - Title Page - Endorsement notice - C

3、ommon modifications prepared by CENELEC technical committee TC 61F date of ratification : 1990-12-10 date of announcement : 1991-06-01 date of withdrawal : 1992-08-01 date of latest publication : 1992-08-01 LIST OF NATIONAL STANDARDS IS GIVEN OVERLEAF HARMONIZED NATIONAL STANDARDS 3404583 0032593 L

4、HD b00.3M S2:1992 AT : BE : CH : DE : DK : ES : FI : FR : GB : GR : IE : IS : IT : LU : NL : NO : PT : SE : NOS No standard SP Standard in preparation NR Standard under revision - . 7 3404583 0032594 3 i o HARMONIZATION DOCUMENT DOCUMENT DHARMONISATION HARMONISIERUNGSDOKUMENT HD 400.3M S2 February 1

5、992 UDC 621.9-182.4-83:621.313.13 Descriptors: Hand-held motor operated tools, particular requirements on safety, planers ENGLISH VERSION HAND-HELD MOTOR OPERATED TOOLS PART II: PARTICULAR SPECIFICATIONS SECTION M: PLANERS (CEE 20-2M:1977, modified) Outils portatifs a main moteur Handgefhrte Elektro

6、werkzeuge Partie II: Regles particulieres Teil II: Besondere Bestimmungen Section M : Rabots Hauptabschnitt M: Hobel (CEE 20-2M31977, modifie) (CEE 20-2M31977, modifiziert) This Harmonization Document was approved by CENELEC on 1990-12-10. CENELEC members are bound to comply with the CEN/CENELEC Int

7、ernal Regulations which stipulate the conditions for implementation of this Harmonization Document on a national level. Up-to-date lists and bibliographical references concerning national implementation may be obtained on application to the Central Secretariat or to any CENELEC member. This Harmoniz

8、ation Oocument exists in three official versions (English, French, German). CENELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and

9、United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, 8-1050 Brussels 01992 Copyright reserved to CENELEC members HD 400.3M S2:1992 E -

10、3404583 O032595 5 Page 2 HD 400.3M S2:1992 FOREWORD This second edition of the Harmonization Document, which includes amendment Al, has been prepared by the secretariat of CENELEC Technical Committee TC 61F in accordance with the decisions taken by this committee. HD 400.3M S2 was approved by CENELE

11、C on 28 June 1988. Amendment Al to this standard was approved on 10 December 1990. The text of the amendment is indicated in this document by a vertical line in the left margin of the text. The following dates were fixed: - latest date of announcement of the HD at national level (doa) a harmonized n

12、ational standard (dopl conflicting national standards (dow) - latest date of publication of - latest date of withdrawal of 1991-06-01 1992-08-01 1992-08-01 For products which have complied with HD 400.3M S1:1981 before 1992-08-01, as shown by the manufacturer or by a certification body, this previou

13、s standard may continue to apply for production until 1997-08-01. This section M of HD 400.3 has to be used together with HD 400.1 S1:1980 and its amendment A1:1991, which are referred to in this document as Part I. The clauses of this section supplement or modify the corresponding clauses in Part I

14、. Where there is no corresponding clause or subclause in this section, the clause or subclause of Part I applies without modification as far as is reasonable. Where the text states “addition“, “modification“ or “replacement“ , the relevant requirement , test specification or explanation of Part I ha

15、s to be adapted accordingly. In this document the following print types are used: - Requirements: xy - Test specification: xy - Notes: XY m 3404583 00325b 7 m Page 3 HD 400.3M S2:1992 1. SCOPE 1.1 Modification: This section applies to planers. NOTE: For Planers with cutting width more than 150 IRR o

16、ther requirements may be necessary. 2. DEFINITIONS 2.2 8. Addition: The rated no-load speed is the speed obtained when the planer has been running idle for 10 min. 18. Modification: Normal load denotes the load obtained when the planer is operated continuously the load being such that the input, in

17、Watts, is equal to rated input. Addition : For tests to be made under normal load the spindle of the motor may be loaded by means of a brake. Addition : 29. Cuttinu head denotes the assembly of blades, drums, blade fixing elements, relevant screws and spindle, the whole being ready for working. 7. M

18、ARKING 7.1 Addition: Planers shall be marked with: - Rated no-load speed, in revolutions per minute, of the - Indication of direction of rotation: cutting head, marked on the nameplate The direction of rotation of the cutting head shall be clearly indicated by an arrow, raised or sunk, or by any oth

19、er means no less visible and indelible. Page 4 HD 400.3M S2:1992 7.13 10.1 10.2 11.1 ” Addition : The planer shall be provided with an instruction sheet in which the substance of the following information shall be contained: - Instruction for replacement of the blades (adjustment) - The necessity of

20、 the use of sharp blades - Wait for complete run-down before putting the tool - Types of cutting heads which can be used. aside Moreover, if a planer is suitable for, and used in, an inverted position as a stationary machine, the instruction sheet shall contain also the following information: - Use

21、of the movable guard - Machining of small work-pieces with push stick - Disconnection of the tool from mains supply before fitting a planer to a stand for use in the inverted posit ion - Use of the switch. Where applicable the instruction sheet shall state how to connect the external suction equipme

22、nt. 10. INPUT AND CURRENT Modification: This test is not made. Addition : Compliance is checked by measuring the current after the planer has been operating for 10 min. 11. HEATING Addition: The planer is operated for 30 mina 18. MECHANICAL HAZARDS Addition: 18.3 to 18.6 Reserved. 3404583 0032598 O

23、18.7 18.8 18.9 Page 5 HD 400.3M S2:1992 Cutting heads must have a circular section along the whole cutting width except for the blades, the fixing screws and full chip clearance area. The blades shall not project by more than 1.1 mm radially beyond the drum (as per dimension “a“ in figure M1). Compl

24、iance is checked by measurement. The maximum chip clearance distance, in mm, to be provided is given by the formula: For d 80 mm : S max = 0.1 x d + 18 Compliance is checked by measurement. 18.10 The distance b (see figure M1) between the rotating circle of the cutting edges and the lips of the adju

25、stable shoe shall not exceed 5 mm, from zero to the maximum adjustable planing depth. Compliance is checked by measurement and inspection. Chip clearance distance Figure Hl Page 6 HD 400.3M S2:1992 3404583 0032599 2 18.11 The blades shall be fixed to the drum in such a way that friction alone is not

26、 relied upon to prevent ejection of the blades. The clamping screws if any shall engage for a minimum of five full threads when the blades are fitted to a steel drum. When the drum is made of a material other than steel the clamping arrangement shall have the same degree of strength etc. as that pro

27、vided by the requirements for the clamping screws for steel drums. Compliance is checked by measurement and inspection. 18.12 The lock system between drum and blade shall be so designed and made that replacement and adjustment of the blades does not compromise safety. Compliance is checked by inspec

28、tion and manual test. 18.13 The clamping screws or the blade fixing elements used to clamp the blades on the drum shall be made of steel with a hardness of at least 20 HRC and a stensile strength of at least 800 N/mmZ. The clamping screws or the bolts shall not project above the max. diameter of the

29、 drum. 18.14 It shall not be possible to touch rotating parts from the sides. Compliance is checked by the following test: The planer with the shoe is placed resting on a flat surface and accessibility of rotating parts is checked by means of the test probe as shown in figure M2. 18.15 Planers with

30、rabbeting facilities shall be provided with a guard that avoids inadvertent contact with the blades on the side. Compliance is checked by inspection and applying the test probe of figure M2 without any force. Handle section Dimensions in mm Figure H2 3404583 O032600 5 Page 7 HD 400.3M S2:1992 18.16

31、It shall not be possible to touch the blades through the chip ejection opening. Compliance is checked by testing all apertures for chip ejection with the test probe of figure M2. It shall not be possible to touch the blades fo the cutting head at any angle of the probe. 18.17 If according to the man

32、ufacturers instructions a planer is suitable for use in an inverted position with an appropriate stand an integrated or additional guard shall be provided, with the stand or with the planer, which covers the cutting head when the planer is not in use. If a parallel guide is provided its guiding and

33、top surface shall have no openings or projections. Openings the maximum dimension of which is 10 mm are disregarded. The guard and the parallel guide shall be so designed that for any cutting width the unused part of the cutting head is covered. The guard provided shall return automatically to the c

34、losed position at the end of the planing operation. Planers provided with an integrated non detachable non-lockable guard which automatically closes, state of rest the cutting head, e.g., concentrically and over the whole width, do not need in stationary operation an additional guard to the above de

35、scribed parallel guide. Examples of parallel guide and guards are given in figure M3. and in the Any contact between steel and other hard material guards with the blades is to be avoided. If the guard or parallel guide are designed in such a way that their contact with the cutting head is not avoide

36、d, they shall be made of soft material (e.9. wood, plastic material, aluminium). Compliance is checked by inspection. W 3404583 0032bOL i I L ._ . Page 8 HD 400.3M S2:1992 Parallel guide Figure X3 20. CONSTRUCTION 20.11 Replacement: Planers shall be fitted with a mains switch such that the motor is

37、switched off automatically as soon as the actuating member of the switch is released. This swith shall have no arrangement to lock it in the “on“ position. When planers which may be used with an appropriate stand in the inverted position are mounted in the stand, means may be provided with the stand to hold the mains switch in the “on“ position. It shall be possible to switch off easily by the user. Compliance is checked by inspection and by manual test. I 2 O. 22. Addition : Planers are considered tools for which provisions of Part 1 regarding dust collection apply.