EN ISO 17708-2018 Footwear - Test methods for whole shoe - Upper sole adhesion.pdf

《EN ISO 17708-2018 Footwear - Test methods for whole shoe - Upper sole adhesion.pdf》由会员分享，可在线阅读，更多相关《EN ISO 17708-2018 Footwear - Test methods for whole shoe - Upper sole adhesion.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Footwear - Test methods for whole shoe - Upper sole adhesionBS EN ISO 17708:2018National forewordThis British Standard is the UK implementation of EN ISO 17708:2018. It is identical to ISO 17708:2018. It supersedes BS E

2、N ISO 17708:2003, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee TCI/69, Footwear A is the average width determined according to 6.2.1.Round the results off to the nearest tenth of a millimetre.NOTE For footwear where the bonding margins vary, proceed

3、 differently. Note the strength after the unsticking of 10 mm and note the corresponding assembling margin. Then, calculate the local upper-sole adhesion, Ri.Calculate the average value of Ri.7.2 Evaluation of the mode of the bond failureThe appearance of the separated areas (see 6.2.2) shall be cla

4、ssified according to the following codes.7.2.1 Separation of the adhesive film from one of the materials (defective adhesion, see Figure 6): Code AFigure 6 Defective adhesion ISO 2018 All rights reserved 7BS EN ISO 17708:2018ISO 17708:20187.2.2 Separation in the adhesive film without unsticking (def

5、ective cohesion, see Figure 7): Code CFigure 7 Defective cohesion7.2.3 Wrong joining of the two adhesive films (defective coalescence, see Figure 8): Code NFigure 8 Defective coalescence7.2.4 Delamination of material (see Figure 9): Code SFigure 9 Material delamination8 ISO 2018 All rights reservedB

6、S EN ISO 17708:2018ISO 17708:20187.2.5 Partial or complete breaking of material (see Figure 10): Code MFigure 10 Partial or complete breaking of the material8 Test reportThe test report shall include the following information:a) reference to this document, ISO 17708;b) characteristics of the sample

7、used (material, footwear type, construction type);c) values of pulling off for each individual determination (minimum, maximum, average);d) bonding margin width for each sample;e) upper-sole adhesion, in newtons per millimetre, for each sample;f) material appearance code;g) use of the ageing procedu

8、re (when applicable), as well as all the conditions or details which can have an influence on results, even if they are not recorded in this document;h) any deviation from this test method;i) date of testing. ISO 2018 All rights reserved 9BS EN ISO 17708:2018ISO 17708:2018Annex A (normative) Ageing

9、process conditions for the upper-sole bonding testA.1 GeneralThis annex defines the ageing process conditions for the test of upper-sole adhesion.A.2 PrincipleThe accelerated thermal ageing is used to determine the measured adhesion evolution according to Clause 6, to estimate the bonding quality af

10、ter ageing.A.3 SamplesClause 5 describes the preparation of samples submitted to ageing.The initial adhesion of the shoe model shall be determined in advance.A.4 ApparatusThe following apparatus shall be used.A.4.1 Circulating air oven, which can be maintained at a temperature of 50 C 2 C or 70 C 2

11、C.A.4.2 Fixture or holding device for test pieces.A.5 Accelerated ageing conditionsA.5.1 Standard ageing conditionsThe test pieces are placed in an oven with forced circulation (see A.4.1) at a temperature of 50 C 2 C for 7 days, without contact between the test pieces and the wall of the circulatin

12、g air oven.After this period and before the adhesion test, the test pieces are conditioned for 24 h according to ISO 18454.A.5.2 Production controlFor production control, it is possible to use other conditions, to have quicker results. These conditions are as follows.The test pieces are placed in an

13、 oven with forced circulation (see A.4.1) at a temperature of 70 C 2 C, for 72 h.After this period and before the adhesion test, the test pieces are conditioned for 24 h according to ISO 18454.NOTE The ageing conditions specified in A.5.1 and A.5.2 cannot give equivalent results.10 ISO 2018 All righ

14、ts reservedBS EN ISO 17708:2018ISO 17708:2018Bibliography1 ISO 20344, Personal protective equipment Test methods for footwear2 EN 344 (all parts)1), Safety, protective and occupational footwear for professional use3 EN 1392, Adhesives for leather and footwear materials Solvent-based and dispersion a

15、dhesives Testing of bond strength under specified conditions4 EN 15307, Adhesives for leather and footwear materials Sole-upper bonds Minimum strength requirements1) Withdrawn. ISO 2018 All rights reserved 11BS EN ISO 17708:2018This page deliberately left blankBSI is the national body responsible fo

16、r preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, in

17、dustry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all si

18、zes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge

19、Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased.If you need international and foreign standards from other Standards Development Organ

20、izations, hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the internationa

21、l standardization bodies) and has formally licensed such information to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly d

22、isplay the standard or any portion thereof in any manner whatsoever without BSIs prior written consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchased in soft copy format is licensed to a sole named user for personal or internal company use only. The

23、standard may be stored on more than 1 device provided that it is accessible by the sole named user only and that only 1 copy is accessed at any one time. A single paper copy may be printed for personal or internal company use only. Standards purchased in hard copy format: A British Standard purchase

24、d in hard copy format is for personal or internal company use only. It may not be further reproduced in any format to create an additional copy. This includes scanning of the document.If you need more than 1 copy of the document, or if you wish to share the document on an internal network, you can s

25、ave money by choosing a subscription product (see Subscriptions).Reproducing extractsFor permission to reproduce content from BSI publications contact the BSI Copyright & Licensing team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further i

26、nformation on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date.You can keep in touch with stand

27、ards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member.PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your stan

28、dards when theyre revised or replaced.To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With

29、updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your bus

30、iness. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.Useful ContactsCustomer ServicesTel: +44 345 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 345 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: BSI Group Headquarters389 Chiswick High Road London W4 4AL UKNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW