EN IEC 61340-4-3-2018 Electrostatics ParT 4-3 Standard Test Methods for Specific Applications - Footwear.pdf

《EN IEC 61340-4-3-2018 Electrostatics ParT 4-3 Standard Test Methods for Specific Applications - Footwear.pdf》由会员分享，可在线阅读，更多相关《EN IEC 61340-4-3-2018 Electrostatics ParT 4-3 Standard Test Methods for Specific Applications - Footwear.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06ElectrostaticsPart 4-3: Standard test methods for specific applications - Footwear (IEC 61340-4-3:2017)BS EN IEC 61340-4-3:2018EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN IEC 61340-4-3 March 2018 ICS 17.220.99;

2、 29.020; 61.060 Supersedes EN 61340-4-3:2001 English Version Electrostatics - Part 4-3: Standard test methods for specific applications - Footwear (IEC 61340-4-3:2017) Electrostatique - Partie 4-3: Mthodes dessai normalises pour des applications spcifiques - Chaussures (IEC 61340-4-3:2017) Elektrost

3、atik - Teil 4-3: Standard-Prfverfahren fr spezielle Anwendungen - Schuhwerk (IEC 61340-4-3:2017) This European Standard was approved by CENELEC on 2018-01-17. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standar

4、d the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (Engli

5、sh, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of

6、Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Sl

7、ovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels 2018 CENELE

8、C All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN IEC 61340-4-3:2018 E National forewordThis British Standard is the UK implementation of EN IEC 61340-4-3:2018. It is identical to IEC 61340-4-3:2017. It supersedes BS EN 61340-4-3:2002, whic

9、h is withdrawn.The UK participation in its preparation was entrusted to Technical Committee GEL/101, Electrostatics.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contrac

10、t. Users are responsible for its correct application. The British Standards Institution 2018 Published by BSI Standards Limited 2018ISBN 978 0 580 91541 3ICS 29.060.20; 29.020; 61.060; 17.220.99Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard wa

11、s published under the authority of the Standards Policy and Strategy Committee on 30 April 2018.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN IEC 61340-4-3:2018EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN IEC 61340-4-3 March 2018 ICS 17.220.99; 29.020;

12、 61.060 Supersedes EN 61340-4-3:2001 English Version Electrostatics - Part 4-3: Standard test methods for specific applications - Footwear (IEC 61340-4-3:2017) Electrostatique - Partie 4-3: Mthodes dessai normalises pour des applications spcifiques - Chaussures (IEC 61340-4-3:2017) Elektrostatik - T

13、eil 4-3: Standard-Prfverfahren fr spezielle Anwendungen - Schuhwerk (IEC 61340-4-3:2017) This European Standard was approved by CENELEC on 2018-01-17. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the st

14、atus of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, Fren

15、ch, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria,

16、 Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia,

17、Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels 2018 CENELEC All ri

18、ghts of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN IEC 61340-4-3:2018 E BS EN IEC 61340-4-3:2018EN IEC 61340-4-3:2018 (E) 2 European foreword The text of document 101/544/FDIS, future edition 2 of IEC 61340-4-3, prepared by IEC/TC 101 “Electrostatic

19、s“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN IEC 61340-4-3:2018. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2018-10-17 latest date

20、 by which the national standards conflicting with the document have to be withdrawn (dow) 2021-01-17 This document supersedes EN 61340-4-3:2001. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC shall not be held responsible

21、 for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 61340-4-3:2017 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following note has to be added for the standard indicat

22、ed : IEC 61340-2-3 NOTE Harmonized as EN 61340-2-3. BS EN IEC 61340-4-3:2018EN IEC 61340-4-3:2018 (E) 3 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents are referred to in the text in such a way that some o

23、r all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 Where an International Publication has been modified by common modi

24、fications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu. Publication Year Title EN/HD Year IEC 62631-3-1 - Dielectric and resistive properties of solid insulating

25、materials - Part 3-1 Determination of resistive properties (DC methods) - Volume resistance and volume resistivity, general method EN 62631-3-1 - IEC 62631-3-2 - Dielectric and resistive properties of solid insulating materials - Part 3-2 Determination of resistive properties (DC methods) - Surface

26、resistance and surface resistivity EN 62631-3-2 - IEC 62631-3-3 - Dielectric and resistive properties of solid insulating materials - Part 3-3: Determination of resistive properties (DC methods) - Insulation resistance EN 62631-3-3 - BS EN IEC 61340-4-3:2018 2 IEC 61340-4-3:2017 IEC 2017 CONTENTS FO

27、REWORD . 3 INTRODUCTION . 5 1 Scope 6 2 Normative references . 6 3 Terms and definitions. 6 4 Test specimens . 7 5 Environment for conditioning and testing 7 5.1 Conditioning and controlled environment for qualification tests . 7 5.2 Environment for acceptance tests 7 6 Test report . 7 7 Test equipm

28、ent 8 7.1 Load applied to footwear under test . 8 7.2 Conductive electrode . 8 7.3 Counter electrode 8 7.4 Insulative support plate . 8 7.5 Resistance measurement apparatus 8 7.5.1 General . 8 7.5.2 Laboratory evaluations (qualification testing) 8 7.5.3 Acceptance testing . 9 7.6 Environmental test

29、chamber 9 8 Test procedure 9 9 Repeatability and reproducibility . 10 Bibliography 11 Figure 1 Form-fitting weight and measuring set-up (schematic) . 9 Table 1 Controlled conditions for electrical measurements 7 BS EN IEC 61340-4-3:2018IEC 61340-4-3:2017 IEC 2017 3 INTERNATIONAL ELECTROTECHNICAL COM

30、MISSION _ ELECTROSTATICS Part 4-3: Standard test methods for specific applications Footwear FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC

31、 is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS)

32、and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with t

33、he IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearl

34、y as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that

35、sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees

36、undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any

37、 attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edi

38、tion of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether di

39、rect or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispen

40、sable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61340-4-3

41、 has been prepared by IEC technical committee 101: Electrostatics. This second edition cancels and replaces the first edition published in 2001. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) c

42、lassification of footwear as electrostatic conductive or electrostatic dissipative has been removed classification is not specified; b) environmental classes for laboratory testing have been removed one set of conditions for pre-conditioning, conditioning and testing is specified; c) reference to IE

43、C 61340-2-3 for measuring the resistance of the counter electrode inserted inside footwear has been removed. BS EN IEC 61340-4-3:2018 4 IEC 61340-4-3:2017 IEC 2017 The text of this International Standard is based on the following documents: FDIS Report on voting 101/544/FDIS 101/550/RVD Full informa

44、tion on the voting for the approval of this International Standard can be found in the report on voting indicated in the above table. This document has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all the parts in the IEC 61340 series, published under the general title E

45、lectrostatics, can be found on the IEC website. The committee has decided that the contents of this document will remain unchanged until the stability date indicated on the IEC website under “http:/webstore.iec.ch“ in the data related to the specific document. At this date, the document will be reco

46、nfirmed, withdrawn, replaced by a revised edition, or amended. BS EN IEC 61340-4-3:2018IEC 61340-4-3:2017 IEC 2017 5 INTRODUCTION Footwear, especially shoes, has become an important electrostatic control device in all areas, but particularly in electronics manufacturing. Standards exist from various

47、 national committees and these have served as guidance in the preparation of this part of IEC 61340 for electrostatic control footwear. Control of unwanted electrostatic charge is of particular importance where personnel work around electrostatic-sensitive processes, materials or items. In many case

48、s, devices such as wrist straps are employed to provide an electrical bond between a persons skin and a ground connection. Many instances exist in industry where wrist straps or other tethering devices cannot be safely or conveniently applied, but there is still a need to provide a ground connection

49、 for personnel. A convenient method to provide a ground connection for personnel is through their footwear while standing or walking on a defined and properly specified electrostatic control floor surface. The measurement method described in this document can be used to monitor electrical specifications of footwear during manufacture, prior to selection by an end user or periodically during use. The method described involves the use of a specific set of test equipment and instruments. Othe