EN IEC 61249-2-47-2018 Materials for printed boards and other interconnecting structures - ParT 2-47 Reinforced base materials clad and unclad - Nonhalogenated .pdf

《EN IEC 61249-2-47-2018 Materials for printed boards and other interconnecting structures - ParT 2-47 Reinforced base materials clad and unclad - Nonhalogenated .pdf》由会员分享，可在线阅读，更多相关《EN IEC 61249-2-47-2018 Materials for printed boards and other interconnecting structures - ParT 2-47 Reinforced base materials clad and unclad - Nonhalogenated .pdf（28页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Materials for printed boards and other interconnecting structuresPart 2-47: Reinforced base materials clad and unclad - Non-halogenated epoxide non-woven/woven E-glass reinforced laminate sheets of thermal conductivity

2、2,0 W/(mK) and defined flammability (vertical burning test), copper-clad for lead-free assemblyBS EN IEC 61249-2-47:2018EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN IEC 61249-2-47 March 2018 ICS 31.180 English Version Materials for printed boards and other interconnecting structures - Part 2

3、-47: Reinforced base materials clad and unclad - Non-halogenated epoxide non-woven/woven E-glass reinforced laminate sheets of thermal conductivity (2.0W/m K) and defined flammability (vertical burning test), copper-clad for lead-free assembly (IEC 61249-2-47:2018) Matriaux pour circuits imprims et

4、autres structures dinterconnexion - Partie 2-47 : Matriaux de base renforcs, plaqus et non plaqus - Feuilles stratifies renforces en verre de type E tiss/non tiss poxyde non halogn, plaques cuivre de conductivit thermique (2,0W/m mK) et dinflammabilit dfinie (essai de combustion verticale) pour les

5、assemblages sans plomb (IEC 61249-2-47:2018) Materialien fr Leiterplatten und andere Verbindungsstrukturen - Teil 2-47: Kaschierte und unkaschierte verstrkte Basismaterialien - Kupferkaschierte, mit E-Glaswirrfaser im Kernbereich und E-Glasgewebe in den Auenlagen verstrkte Laminattafeln auf der Basi

6、s von halogenfreiem Epoxidharz mit Wrmeleitfhigkeit (2,0 W/mK) und definierter Brennbarkeit (vertikale Prflingslage) fr bleifreie Bestckungstechnik (IEC 61249-2-47:2018) This European Standard was approved by CENELEC on 2018-02-14. CENELEC members are bound to comply with the CEN/CENELEC Internal Re

7、gulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELE

8、C member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official v

9、ersions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,

10、 the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CEN

11、ELEC Management Centre: Rue de la Science 23, B-1040 Brussels 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN IEC 61249-2-47:2018 E National forewordThis British Standard is the UK implementation of EN IEC 61249-2-47:2018. It i

12、s identical to IEC 61249-2-47:2018.The UK participation in its preparation was entrusted to Technical Committee EPL/501, Electronic Assembly Technology.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all t

13、he necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2018 Published by BSI Standards Limited 2018ISBN 978 0 580 99201 8ICS 31.180Compliance with a British Standard cannot confer immunity from legal obligations.This British Standa

14、rd was published under the authority of the Standards Policy and Strategy Committee on 30 April 2018.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN IEC 61249-2-47:2018EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN IEC 61249-2-47 March 2018 ICS 31.180 Engl

15、ish Version Materials for printed boards and other interconnecting structures - Part 2-47: Reinforced base materials clad and unclad - Non-halogenated epoxide non-woven/woven E-glass reinforced laminate sheets of thermal conductivity (2.0W/m K) and defined flammability (vertical burning test), coppe

16、r-clad for lead-free assembly (IEC 61249-2-47:2018) Matriaux pour circuits imprims et autres structures dinterconnexion - Partie 2-47 : Matriaux de base renforcs, plaqus et non plaqus - Feuilles stratifies renforces en verre de type E tiss/non tiss poxyde non halogn, plaques cuivre de conductivit th

17、ermique (2,0W/m mK) et dinflammabilit dfinie (essai de combustion verticale) pour les assemblages sans plomb (IEC 61249-2-47:2018) Materialien fr Leiterplatten und andere Verbindungsstrukturen - Teil 2-47: Kaschierte und unkaschierte verstrkte Basismaterialien - Kupferkaschierte, mit E-Glaswirrfaser

18、 im Kernbereich und E-Glasgewebe in den Auenlagen verstrkte Laminattafeln auf der Basis von halogenfreiem Epoxidharz mit Wrmeleitfhigkeit (2,0 W/mK) und definierter Brennbarkeit (vertikale Prflingslage) fr bleifreie Bestckungstechnik (IEC 61249-2-47:2018) This European Standard was approved by CENEL

19、EC on 2018-02-14. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standard

20、s may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language a

21、nd notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Ge

22、rmany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de N

23、ormalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN IEC 61249-2-47:2018 E BS EN IEC

24、 61249-2-47:2018EN IEC 61249-2-47:2018 (E) 2 European foreword The text of document 91/1449/FDIS, future edition 1 of IEC 61249-2-47, prepared by IEC/TC 91 “Electronics assembly technology“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN IEC 61249-2-47:2018. The followin

25、g dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2018-11-14 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2021-02-14 Attention i

26、s drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 61249-2-47:2018 was approved by CENELEC as a E

27、uropean Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: ISO 9000 NOTE Harmonized as EN ISO 9000. ISO 14001 NOTE Harmonized as EN ISO 14001. BS EN IEC 61249-2-47:2018EN IEC 61249-2-47:2018 (E) 3 Annex ZA (

28、normative) Normative references to international publications with their corresponding European publications The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited app

29、lies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date information on the latest versions of

30、 the European Standards listed in this annex is available here: www.cenelec.eu. Publication Year Title EN/HD Year IEC 61189-2 2006 Test methods for electrical materials, printed boards and other interconnection structures and assemblies - Part 2: Test methods for materials for interconnection struct

31、ures EN 61189-2 2006 IEC 61249-5-1 - Materials for interconnection structures - Part 5: Sectional specification set for conductive foils and films with or without coatings - Section 1: Copper foils (for the manufacture of copper-clad base materials) EN 61249-5-1 - IEC/PAS 61249-6-3 - Specification f

32、or finished fabric woven from “E“ glass for printed boards - - ISO 11014 - Safety data sheet for chemical products - Content and order of sections - - BS EN IEC 61249-2-47:2018 2 IEC 61249-2-47:2018 IEC 2018 CONTENTS FOREWORD . 4 1 Scope 6 2 Normative references . 6 3 Terms and definitions. 6 4 Mate

33、rials and construction . 7 4.1 General . 7 4.2 Resin system 7 4.3 Metal foil . 7 4.4 Reinforcement . 7 5 Electrical properties . 7 6 Non-electrical properties of the copper-clad laminate . 8 6.1 Appearance of the copper-clad sheet. 8 6.1.1 General . 8 6.1.2 Indentations (pits and dents) 8 6.1.3 Wrin

34、kles 8 6.1.4 Scratches 8 6.1.5 Raised areas . 9 6.2 Appearance of the unclad face 9 6.3 Laminate thickness . 9 6.4 Bow and twist 9 6.5 Properties related to the copper foil bond 10 6.6 Punching and machining . 11 6.7 Dimensional stability 11 6.8 Sheet sizes . 11 6.8.1 Typical sheet sizes . 11 6.8.2

35、Tolerances for sheet sizes . 11 6.9 Cut panels. 12 6.9.1 Cut panel sizes 12 6.9.2 Size tolerances for cut panels 12 6.9.3 Rectangularity of cut panels . 12 6.10 Thermal conductivity . 12 7 Non-electrical properties of the base material after complete removal of the copper foil . 13 7.1 Appearance of

36、 the dielectric base material 13 7.2 Flexural strength . 13 7.3 Flammability 13 7.4 Water absorption . 14 7.5 Measling . 14 7.6 Glass transition temperature and cure factor . 14 7.7 Decomposition temperature . 15 7.8 Time to delamination (TMA) 15 7.9 Halogen content 15 8 Quality assurance 15 8.1 Qua

37、lity system 15 8.2 Responsibility for inspection 16 8.3 Qualification inspection . 16 8.4 Quality conformance inspection . 16 BS EN IEC 61249-2-47:2018IEC 61249-2-47:2018 IEC 2018 3 8.5 Certificate of conformance 16 8.6 Safety data sheet 16 9 Packaging and marking 16 10 Ordering information 17 Annex

38、 A (informative) Engineering information . 18 A.1 General . 18 A.2 Chemical properties 18 A.3 Electrical properties 18 A.4 Flammability properties . 18 A.5 Mechanical properties . 18 A.6 Physical properties 18 A.7 Thermal properties 18 Annex B (informative) Common laminate constructions . 20 Annex C

39、 (informative) Guideline for qualification and conformance inspection . 21 Bibliography 22 Table 1 Electrical properties . 7 Table 2 Size of indentations . 8 Table 3 Nominal thickness and tolerance of metal-clad laminate . 9 Table 4 Bow and twist requirements . 10 Table 5 Pull-off and peel strength

40、requirements 10 Table 6 Dimensional stability 11 Table 7 Size tolerances for cut panels 12 Table 8 Rectangularity of cut panels . 12 Table 9 Thermal conductivity 12 Table 10 Flexural strength requirements . 13 Table 11 Flammability requirements . 14 Table 12 Water absorption requirements 14 Table 13

41、 Measling requirements . 14 Table 14 Glass transition temperature and cure factor requirements . 15 Table 15 Decomposition temperature requirements 15 Table 16 Time to delamination requirements. 15 Table 17 Halogen content . 15 Table C.1 Qualification and conformance inspection . 21 BS EN IEC 61249-

42、2-47:2018 4 IEC 61249-2-47:2018 IEC 2018 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ MATERIALS FOR PRINTED BOARDS AND OTHER INTERCONNECTING STRUCTURES Part 2-47: Reinforced base materials clad and unclad Non-halogenated epoxide non-woven/woven E-glass reinforced laminate sheets of thermal conductivi

43、ty 2,0 W/(mK) and defined flammability (vertical burning test), copper-clad for lead-free assembly FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object

44、 of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications

45、 (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising

46、 with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, a

47、s nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees i

48、n that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Comm

49、ittees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access t