EN IEC 60512-15-2-2018 Connectors for electrical and electronic equipment - Tests and measurements - ParT 15-2 Connector tests (mechanical) - Test 15b Insert re.pdf

《EN IEC 60512-15-2-2018 Connectors for electrical and electronic equipment - Tests and measurements - ParT 15-2 Connector tests (mechanical) - Test 15b Insert re.pdf》由会员分享，可在线阅读，更多相关《EN IEC 60512-15-2-2018 Connectors for electrical and electronic equipment - Tests and measurements - ParT 15-2 Connector tests (mechanical) - Test 15b Insert re.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Connectors for electrical and electronic equipment - Tests and measurementsPart 15-2: Connector tests (mechanical) - Test 15b: Insert retention in housing (axial)BS EN IEC 60512-15-2:2018EUROPEAN STANDARD NORME EUROPENN

2、E EUROPISCHE NORM EN IEC 60512-15-2 March 2018 ICS 31.220.10 Supersedes EN 60512-15-2:2008 English Version Connectors for electrical and electronic equipment - Tests and measurements - Part 15-2: Connector tests (mechanical) - Test 15b: Insert retention in housing (axial) (IEC 60512-15-2:2018) Conne

3、cteurs pour quipements lectriques et lectroniques - Essais et mesures - Partie 15-2: Essais (mcaniques) des connecteurs - Essai 15b: Rtention de lisolant dans le botier (axial) (IEC 60512-15-2:2018) Steckverbinder fr elektronische Einrichtungen - Mess- und Prfverfahren - Teil 15-2: Mechanische Prfun

4、gen an Steckverbindern - Prfung 15b: Haltekraft des Einsatzes im Gehuse (axial) (IEC 60512-15-2:2018) This European Standard was approved by CENELEC on 2018-02-16. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European St

5、andard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (

6、English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committee

7、s of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovaki

8、a, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels 2018 C

9、ENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN IEC 60512-15-2:2018 E National forewordThis British Standard is the UK implementation of EN IEC 60512152:2018. It is identical to IEC 60512152:2018. It supersedes BS EN 60512152:2008, w

10、hich is withdrawn.The UK participation in its preparation was entrusted to Technical Committee EPL/48, Electromechanical components and mechanical structures for electronic equipment.A list of organizations represented on this committee can be obtained on request to its secretary.This publication do

11、es not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2018 Published by BSI Standards Limited 2018ISBN 978 0 580 91815 5ICS 31.220.10Compliance with a British Standard cannot confer immunity from leg

12、al obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2018.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN IEC 60512152:2018EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN IEC 60512

13、-15-2 March 2018 ICS 31.220.10 Supersedes EN 60512-15-2:2008 English Version Connectors for electrical and electronic equipment - Tests and measurements - Part 15-2: Connector tests (mechanical) - Test 15b: Insert retention in housing (axial) (IEC 60512-15-2:2018) Connecteurs pour quipements lectriq

14、ues et lectroniques - Essais et mesures - Partie 15-2: Essais (mcaniques) des connecteurs - Essai 15b: Rtention de lisolant dans le botier (axial) (IEC 60512-15-2:2018) Steckverbinder fr elektronische Einrichtungen - Mess- und Prfverfahren - Teil 15-2: Mechanische Prfungen an Steckverbindern - Prfun

15、g 15b: Haltekraft des Einsatzes im Gehuse (axial) (IEC 60512-15-2:2018) This European Standard was approved by CENELEC on 2018-02-16. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a nationa

16、l standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A ve

17、rsion in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgari

18、a, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Sw

19、itzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels 2018 CENELEC All rights of exploitat

20、ion in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN IEC 60512-15-2:2018 E BS EN IEC 60512152:2018EN IEC 60512-15-2:2018 (E) 2 European foreword The text of document 48B/2489/CDV, future edition 2 of IEC 60512-15-2, prepared by IEC/SC 48B “Electrical connectors“ of IE

21、C/TC 48 “Electrical connectors and mechanical structures for electrical and electronic equipment“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN IEC 60512-15-2:2018. The following dates are fixed: latest date by which the document has to be implemented at national level

22、 by publication of an identical national standard or by endorsement (dop) 2018-11-16 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2021-02-16 This document supersedes EN 60512-15-2:2008. Attention is drawn to the possibility that some of the ele

23、ments of this document may be the subject of patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 60512-15-2:2018 was approved by CENELEC as a European Standard without any modification. In t

24、he official version, for Bibliography, the following note has to be added for the standard indicated : IEC 60512-15-3 NOTE Harmonized as EN 60512-15-3. BS EN IEC 60512152:2018EN IEC 60512-15-2:2018 (E) 3 Annex ZA (normative) Normative references to international publications with their corresponding

25、 European publications The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including

26、 any amendments) applies. NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu. Public

27、ation Year Title EN/HD Year IEC 60050-581 - International Electrotechnical Vocabulary - Part 581: Electromechanical components for electronic equipment - - IEC 60512-1 - Connectors for electronic equipment - Tests and measurements - Part 1: General EN 60512-1 - IEC 60512-1-1 - Connectors for electro

28、nic equipment - Tests and measurements - Part 1-1: General examination - Test 1a: Visual examination EN 60512-1-1 - BS EN IEC 60512152:2018This page deliberately left blank 2 IEC 60512-15-2:2018 IEC 2018 CONTENTS FOREWORD . 3 1 Scope 5 2 Normative references 5 3 Terms and definitions 5 4 Preparation

29、 6 4.1 Test equipment . 6 4.2 Preparation of specimen . 6 4.3 Mounting of specimen . 6 5 Test / measuring method . 6 5.1 Pre-conditioning 6 5.2 Initial measurements . 6 5.3 Tests 6 5.4 Recovery 7 5.5 Final measurements 7 6 Details to be specified . 7 Bibliography 8 2 IEC 60512-15-2:2018 IEC 2018 CON

30、TENTS FOREWORD . 3 1 Scope 5 2 Normative references 5 3 Terms and definitions 5 4 Preparation 6 4.1 Test equipment . 6 4.2 Preparation of specimen . 6 4.3 Mounting of specimen . 6 5 Test / measuring method . 6 5.1 Pre-conditioning 6 5.2 Initial measurements . 6 5.3 Tests 6 5.4 Recovery 7 5.5 Final m

31、easurements 7 6 Details to be specified . 7 Bibliography 8 BS EN IEC 60512152:2018IEC 60512-15-2:2018 IEC 2018 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ CONNECTORS FOR ELECTRICAL AND ELECTRONIC EQUIPMENT TESTS AND MEASUREMENTS Part 15-2: Connector tests (mechanical) Test 15b: Insert retention in

32、 housing (axial) FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning stand

33、ardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparati

34、on is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with

35、the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjec

36、ts since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical c

37、ontent of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent pos

38、sible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide confor

39、mity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its direct

40、ors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising

41、out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is draw

42、n to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60512-15-2 has been prepared by subcommittee 48B: Electrical connectors, of IEC tech

43、nical committee 48: Electrical connectors and mechanical structures for electrical and electronic equipment. This second edition cancels and replaces the first edition, published in 2008. This edition constitutes a technical revision. This edition includes the following significant technical changes

44、 with respect to the previous edition: The test method B (pressure method) suitable for testing hermetic connector has been added. This edition reflects IEC 60512-1-101, Blank detail specification. BS EN IEC 60512152:2018 4 IEC 60512-15-2:2018 IEC 2018 The text of this International Standard is base

45、d on the following documents: FDIS Report on voting 48B/2614/FDIS 48B/2621/RVD Full information on the voting for the approval of this International Standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives

46、, Part 2. A list of all parts in the IEC 60512 series, published under the general title Connectors for electrical and electronic equipment Tests and measurements, can be found on the IEC website. Future standards in this series will carry the new general title as cited above. Titles of existing sta

47、ndards in this series will be updated at the time of the next edition. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this d

48、ate, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. BS EN IEC 60512152:2018IEC 60512-15-2:2018 IEC 2018 5 CONNECTORS FOR ELECTRICAL AND ELECTRONIC EQUIPMENT TESTS AND MEASUREMENTS Part 15-2: Connector tests (mechanical) Test 15b: Insert retention in housin

49、g (axial) 1 Scope This part of IEC 60512, when required by the detail (product) specification, is used for testing connectors within the scope of technical committee 48. It may also be used for similar devices when specified in a detail (product) specification. The object of this document is to detail a standard test method to assess the effectiveness of the retaining system of a connector insert within a connector housing to withstand axial for