EN 144-2-2018 Respiratory protective devices - Gas cylinder valves - Part 2 Outlet connections.pdf

《EN 144-2-2018 Respiratory protective devices - Gas cylinder valves - Part 2 Outlet connections.pdf》由会员分享，可在线阅读，更多相关《EN 144-2-2018 Respiratory protective devices - Gas cylinder valves - Part 2 Outlet connections.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Respiratory protective devices - Gas cylinder valvesPart 2: Outlet connectionsBS EN 144-2:2018National forewordThis British Standard is the UK implementation of EN 144-2:2018. It supersedes BS EN 144-2:1999, which is wi

2、thdrawn.The UK participation in its preparation was entrusted to Technical Committee PH/4, Respiratory protection.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract.

3、 Users are responsible for its correct application. The British Standards Institution 2018 Published by BSI Standards Limited 2018ISBN 978 0 580 93549 7ICS 13.340.30Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authorit

4、y of the Standards Policy and Strategy Committee on 30 April 2018.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 144-2:2018EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 144-2April 2018ICS 13.340.30 Supersedes EN 144-2:1998EUROPEAN COMMITTEE FOR STANDARDIZAT

5、IONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGCEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2018 CEN Ref. No. EN 144-2:2018: EAll rights of exploitation in any form and by any means reserved worldwide for CEN national MembersRespiratory protective devices - Gas cy

6、linder valves - Part 2: Outlet connectionsAppareils de protection respiratoire - Robinets de bouteille gaz - Partie 2: Raccordements de sortieAtemschutzgerte - Gasflaschenventile - Teil 2: AusgangsanschlsseThis European Standard was approved by CEN on 19 February 2018.CEN members are bound to comply

7、 with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC M

8、anagement Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same

9、status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Ma

10、lta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.English VersionEN 144-2:2018 (E)European foreword 31 Scope . 42 Normative references 43 Terms and definitions . 44 Dimensional and tolerance requirements . 44.1 Gene

11、ral . 44.2 Classification . 44.3 Outlet connections for breathable air of type A1, A2 and A3 . 54.4 Outlet connections for oxygen of type O1 and O2 54.4.1 General 54.4.2 Outlet connection of type O1 . 54.4.3 Outlet connection of type O2 . 64.5 Outlet connections for oxygen/nitrogen mixtures of type

12、M1 and M2 74.5.1 Outlet connection of type M1 74.5.2 Outlet connection of type M2 85 Marking 9Bibliography .102Contents PageBS EN 144-2:2018EN 144-2:2018 (E)European forewordThis document (EN 144-2:2018) has been prepared by Technical Committee CEN/TC 79 “Respiratory protective devices”, the secreta

13、riat of which is held by DIN.This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2018, and conflicting national standards shall be withdrawn at the latest by October 2018.Attention is drawn to

14、 the possibility that some of the elements of this document may be the subject of patent rights. CEN not be held responsible for identifying any or all such patent rights.This document supersedes EN 144-2:1998.The following main technical changes have been made compared to EN 144-2:1998:a) Terms and

15、 definition added;b) new classification scheme added in 4.2;c) outlet connections for breathable air changed to be in accordance with EN ISO 12209, including a new type for working pressure of breathable air above 300 bar up to 400 bar;d) Clause 4 “Marking” completely changed and adapted to Part 1;e

16、) A-deviation deleted.This document is one part of a three-part standard concerning connections for gas cylinder valves for respiratory protective devices: Part 1: Inlet connections Part 2: Outlet connections Part 3: Outlet connections for diving gases Nitrox and oxygen.According to the CEN/CENELEC

17、Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Icelan

18、d, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.3BS EN 144-2:2018EN 144-2:2018 (E)1 ScopeThis European Standard specifies the dimensions, tolerances and mark

19、ing requirements of outlet connections for connecting regulators and cylinder valves for respiratory protective devices except those for diving applications.2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes requireme

20、nts of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.EN 144-1, Respiratory protective devices - Gas cylinder valves - Part 1: Inlet connectionsEN ISO 12209, Gas cylinders -

21、 Outlet connections for gas cylinder valves for compressed breathable air (ISO 12209)3 Terms and definitionsFor the purposes of this document, the terms and definitions given in EN 144-1 apply.ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC El

22、ectropedia: available at http:/www.electropedia.org/ ISO Online browsing platform: available at http:/www.iso.org/obp4 Dimensional and tolerance requirements4.1 GeneralThe outlet connections specified in this European Standard refer to the cylinder valve outlet and a mating connection. Use of the sp

23、ecified filling connector is essential to ensure the safe use of each connection at its intended working pressure.4.2 ClassificationFor the purpose of this European Standard the outlet connections are classified as following:a) Type A1: working pressure of breathable air up to 232 bar;b) Type A2: wo

24、rking pressure of breathable air above 232 bar up to 300 bar;c) Type A3: working pressure of breathable air above 300 bar up to 400 bar;d) Type O1: working pressure of oxygen up to 232 bar;e) Type O2: working pressure of oxygen above 232 bar up to 300 bar;f) Type M1: working pressure of oxygen/nitro

25、gen mixtures up to 232 bar;g) Type M2: working pressure of oxygen/nitrogen mixtures above 232 bar up to 300 bar.The cylinder valve and gas cylinder shall be tested against the maximum working pressure of the pressure range of the connection (i.e. 232 bar, 300 bar or 400 bar).4 BS EN 144-2:2018EN 144

26、-2:2018 (E)4.3 Outlet connections for breathable air of type A1, A2 and A3The outlet connections of types A1, A2 and A3 shall meet EN ISO 12209, except for the marking requirements.4.4 Outlet connections for oxygen of type O1 and O24.4.1 GeneralAll dimensions are given in millimetres and the toleran

27、ces shall be in accordance with ISO 2768-mk.4.4.2 Outlet connection of type O1The Figures 1a) to 1h) show the outlet connection and connectors and their dimensions of type O1.a) Valve outlet connec-tion fitted with connec-torb) Filling connector (assembly) c) Sealing plugd) Valve outlet connec-tione

28、) O-Ring f) Connector g) Hand wheel5BS EN 144-2:2018EN 144-2:2018 (E)h) Detail X enlargedFigure 1 Outlet connection and connectors of type O14.4.3 Outlet connection of type O2The Figures 2a) to 2h) show the outlet connection and connectors and their dimensions of type O2.a) Valve outlet connection f

29、itted with connectorb) Filling connector (assembly) c) Sealing plugd) Valve outlet con-nectione) O-Ring f) Connector g) Hand wheel6 BS EN 144-2:2018EN 144-2:2018 (E)h) Detail X enlargedFigure 2 Outlet connection and connectors of type O24.5 Outlet connections for oxygen/nitrogen mixtures of type M1

30、and M24.5.1 Outlet connection of type M1The Figures 3a) to 3h) show the outlet connection, connectors and their dimensions of type M1.a) Valve outlet connection fitted with connectorb) Filling connector (assembly) c) Sealing plugd) Valve outlet connection e) O-ring f) Connector g) Hand wheel7BS EN 1

31、44-2:2018EN 144-2:2018 (E)h) Detail X enlargedFigure 3 Outlet connection and connectors of type M14.5.2 Outlet connection of type M2The Figures 4a) to 4h) show the outlet connection, connectors and their dimensions of type M2.a) Valve outlet connection fitted with connectorb) Filling connector (asse

32、mbly) c) Sealing plugd) Valve outlet con-nectione) O-Ring f) Connector g) Hand wheel8 BS EN 144-2:2018EN 144-2:2018 (E)h) Detail X enlargedFigure 4 Outlet connection and connectors of type M25 MarkingCylinder valves meeting the requirements of this document shall be marked with:a) the number of this

33、 document, i.e. EN 144-2;NOTE Where the cylinder valve also meets the requirements of EN 144-1 a combined marking, i.e. EN 144-1/-2 can be used.b) means of identification of the manufacturer;c) identification of date of manufacture (at least the year); andd) identification of the thread type followe

34、d by the maximum working pressure the valve is intended to be used, e.g. A1/200 bar. This marking shall be given on the outlet connection or on the valve body.9BS EN 144-2:2018EN 144-2:2018 (E)Bibliography1 EN ISO 10286, Gas cylinders - Terminology (ISO 10286)10 BS EN 144-2:2018This page deliberatel

35、y left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standar

36、ds Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependab

37、le format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standard

38、s by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased.If

39、 you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or some pe

40、rson or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to

41、any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSIs prior written consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchased in soft copy for

42、mat is licensed to a sole named user for personal or internal company use only. The standard may be stored on more than 1 device provided that it is accessible by the sole named user only and that only 1 copy is accessed at any one time. A single paper copy may be printed for personal or internal co

43、mpany use only. Standards purchased in hard copy format: A British Standard purchased in hard copy format is for personal or internal company use only. It may not be further reproduced in any format to create an additional copy. This includes scanning of the document.If you need more than 1 copy of

44、the document, or if you wish to share the document on an internal network, you can save money by choosing a subscription product (see Subscriptions).Reproducing extractsFor permission to reproduce content from BSI publications contact the BSI Copyright & Licensing team.SubscriptionsOur range of subs

45、cription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 a

46、nd is refreshed daily so youll always be up to date.You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member.PLUS is an updating service exclusive to BSI S

47、ubscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced.To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publicat

48、ions on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision.

49、 We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.Useful ContactsCustomer ServicesTel: +44 345 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 345 086 9001Email: Knowledge CentreTel