ISO 8124-4-2014 Safety of toys - Part 4 Swings slides and similar activity toys for indoor and outdoor family domestic use《玩具安全性 第4部分 室内和室外家庭用秋千、滑梯和类似活动玩具》.pdf

《ISO 8124-4-2014 Safety of toys - Part 4 Swings slides and similar activity toys for indoor and outdoor family domestic use《玩具安全性 第4部分 室内和室外家庭用秋千、滑梯和类似活动玩具》.pdf》由会员分享，可在线阅读，更多相关《ISO 8124-4-2014 Safety of toys - Part 4 Swings slides and similar activity toys for indoor and outdoor family domestic use《玩具安全性 第4部分 室内和室外家庭用秋千、滑梯和类似活动玩具》.pdf（70页珍藏版）》请在麦多课文档分享上搜索。

1、 ISO 2014 Safety of toys Part 4: Swings, slides and similar activity toys for indoor and outdoor family domestic use Scurit des jouets Partie 4: Balanoires, glissoires et jouets activit similaire usage domestique familial intrieur et extrieur INTERNATIONAL STANDARD ISO 8124-4 Second edition 2014-10-

2、01 Reference number ISO 8124-4:2014(E) ISO 8124-4:2014(E)ii ISO 2014 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2014 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, i

3、ncluding photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax

4、+ 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ISO 8124-4:2014(E)Contents Page Foreword iv Introduction v 1 Scope . 1 2 Normative references 1 3 T erms and definitions . 1 4 Requirements 6 4.1 General . 6 4.2 Barriers .10 4.3 Rung ladders, stepladders and stairway

5、s .11 4.4 Entrapment .12 4.5 Stability of activity toys other than slides, swings and toys with crossbeams .14 4.6 Slides .15 4.7 Swings 18 4.8 Seesaws 21 4.9 Carousels and rocking toys 22 4.10 Inflatable activity toys .22 4.11 Paddling pools 24 5 Warnings and labelling .25 5.1 Labelling 25 5.2 Asse

6、mbly and installation instructions 25 5.3 Maintenance instructions .26 5.4 Warnings .27 6 Test methods 28 6.1 Stability .28 6.2 Static strength .37 6.3 Dynamic strength of barriers and handrails 38 6.4 Determination of impact from swing elements .39 6.5 Test for head and neck entrapment .42 6.6 Togg

7、le test 47 6.7 Test for protrusions .50 6.8 Durability test for suspension connectors and means of suspension 53 6.9 Deflation of inflatable activity toys .55 6.10 Static load test for paddling pools with non-inflatable walls 55 Annex A (informative) Rationale .56 Annex B (informative) Consumer info

8、rmation sheet for playground surfacing materials .60 Annex C (informative) Safety labelling guidelines for certain types of activity toys .61 Bibliography .63 ISO 2014 All rights reserved iii ISO 8124-4:2014(E) Foreword ISO (the International Organization for Standardization) is a worldwide federati

9、on of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee

10、. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and th

11、ose intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2.

12、 www.iso.org/directives Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the documen

13、t will be in the Introduction and/or on the ISO list of patent declarations received. www.iso.org/patents Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and express

14、ions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT), see the following URL: Foreword - Supplementary information The committee responsible for this document is ISO/TC 181, Safety of toys. This second editio

15、n cancels and replaces the first.edition (ISO 8124-4:2010) and amendment 1 (ISO 8124-4:2010 / Amd.1:2012). This edition incorporates the amendments ISO 8124-4:2010 / Amd.1:2012 and ISO 8124-4:2010/Amd.2:2014. ISO 8124 consists of the following parts, under the general title Safety of toys: Part 1: S

16、afety aspects related to mechanical and physical properties Part 2: Flammability Part 3: Migration of certain elements Part 4: Swings, slides and similar activity toys for indoor and outdoor family domestic use Part 6: Certain phthalate esters in toys and childrens products Part 8: Age determination

17、 guidelines The following parts are under preparation: Part 5: Determination of total concentration of certain elements in toys Part 7: Requirements and test methods for finger paintsiv ISO 2014 All rights reserved ISO 8124-4:2014(E) Introduction This part of ISO 8124 is largely based upon existing

18、standards in the European Union (EN 71-8) and in the United States (ASTM F1148). However, it should not be construed that a toy manufactured in compliance with this part of ISO 8124 will be in full compliance with relevant national toy safety requirements in the market where the product is intended

19、to be distributed. The user of this part of ISO 8124 is therefore advised to be aware of relevant national requirements. Compliance with the requirements of this part of ISO 8124 will minimize potential hazards associated with toys resulting from their use in their intended play modes (normal use) a

20、s well as unintended play modes (reasonable foreseeable abuse). This part of ISO 8124 will not, nor is it intended to, eliminate parental responsibility in the appropriate selection of toys. In addition, this part of ISO 8124 will not eliminate the need for parental supervision in situations where c

21、hildren of various ages may have access to the same toy(s). ISO 2014 All rights reserved v Safety of toys Part 4: Swings, slides and similar activity toys for indoor and outdoor family domestic use 1 Scope This part of ISO 8124 specifies requirements and test methods for activity toys for domestic f

22、amily use intended for children under 14 years to play on or in. Products covered by this part of ISO 8124 include swings, slides, seesaws, carousels, rocking toys, climbing frames, fully enclosed toddler swing seats and other products intended to bear the mass of one or more children. Products not

23、included within the scope of this part of ISO 8124 are: a) fitness and sporting equipment unless attached to the activity toy; b) equipment intended for use in schools, day care centres, kindergartens, public playgrounds, restaurants, shopping centres and similar public places; c) juvenile care prod

24、ucts such as, but not limited to, infant swings, playpens/enclosures, beds or f urnit ure including picnic tables, cradle rockers and products specifically designed for therapeutic use. Inflatable activity toys are included in the scope of this part of ISO 8124. However, a powered blower used to con

25、tinuously inflate the toy is not covered by this part of ISO 8124 since it is considered to be a household appliance and covered by requirements given in IEC 60335-2-80. See A.1. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are

26、indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 8124-1, Safety of toys Part 1: Safety aspects related to mechanical and physical properties 3 T erms

27、a nd definiti ons For the purpose of this document, the terms and definitions given in ISO 8124-1 and the following apply. 3.1 activity toy toy intended for family domestic use, intended to bear the mass of one or more children, the support structure of which remains stationary while the activity is

28、 taking place and which is intended for the performance by a child of any of the following activities: climbing, swinging, sliding, rocking, spinning, jumping, bouncing, crawling and creeping, or any combination thereof EXAMPLE Swings, slides, carousels and climbing frames (see Figure 1). Note 1 to

29、entry: Aquatic toys, paddling pools, trampolines and ride-on vehicles are not considered as activity toys in the context of this part of ISO 8124. INTERNATIONAL ST ANDARD ISO 8124-4:2014(E) ISO 2014 All rights reserved 1 ISO 8124-4:2014(E) “Not to scale” Figure 1 Examples of activity toys 3.2 anchor

30、 device used to fix the toy to the ground surface 3.3 attachment slide slide for which access to the starting section is possible only by passing via other equipment or parts of other equipment 3.4 barrier device intended to prevent children from falling from elevated surfaces 3.5 crossbeam bar or b

31、eam which forms a main load-bearing part of the toy 3.6 entrapment condition in which a body, part of a body or clothing becomes caught and impedes withdrawal 3.7 forced movement movement where the direction and the extent of the childs movement is determined by the operation of the equipment, for e

32、xample swinging, sliding, rocking or revolving2 ISO 2014 All rights reserved ISO 8124-4:2014(E) 3.8 free height of fall greatest vertical distance from the intended body support, for example from the seat of a swing to the impact area below 3.9 free space space in, on or around the activity toy that

33、 can be occupied by a user undergoing a forced movement by the equipment, for example swinging, sliding, rocking or revolving Note 1 to entry: The definition of free space does not include the three-dimensional area in which a falling movement takes place. 3.10 fully enclosed toddler swing seats ful

34、ly enclosed single occupancy swing intended for young children who can sit upright unaided Note 1 to entry: A seat is considered fully enclosed when a containment system is employed to support the child on all sides and in between the legs (see Figure 2). Figure 2 Examples of fully enclosed toddler

35、swing seat 3.11 impact area area of a swing element that comes into contact with the test mass during an impact test in accordance with 6.4 (determination of impact from swing elements) 3.12 infant swing stationary unit with a frame and a powered mechanism enabling an infant to swing in a seated pos

36、ition Note 1 to entry: An infant swing is intended for use with infants from birth until the child is able to sit upright unassisted. 3.13 handrail rail intended to assist the users to balance or steady themselves ISO 2014 All rights reserved 3 ISO 8124-4:2014(E) 3.14 platform any elevated substanti

37、ally horizontal surface intended to be used by a child as a place for play or as a transition between components Note 1 to entry: Slide starting sections less than 129 000 mm 2are not considered platforms. 3.15 slide structure with inclined surface(s) on which the user slides in a defined track See

38、Figure 3. Note 1 to entry: Note1 to entry: Inclined planes, designed primarily for other purposes, such as roofs and ramps, do not constitute slides. Key A starting section B sliding section C run-out section D height of slide B+ C slide length NOTE The dimensions A, B, and C are measured at the cen

39、treline of the sliding surface. Each of these sizes represents one of the zones of the sliding surface. Each zone of the sliding surface is determined by the intersection of the curve of the sliding surface (taken at the bottom of the sliding surface) and the bisecting line of the angle formed betwe

40、en the zones of the sliding surfaces. Figure 3 Diagrammatic representation of a slide 3.16 suspension connector device that forms the direct contact between a crossbeam and the swing device See Figure 4. 3.17 swing structure, normally intended to be attached to or incorporating a crossbeam, suspensi

41、on connectors and a swing device with swing element, means of suspension and suspension coupling See Figure 4.4 ISO 2014 All rights reserved ISO 8124-4:2014(E) Key 1 crossbeam/support member 2 suspension connector 3 suspension coupling 4 means of suspension 5 swing device 6 swing element (e.g. seat,

42、 rings, bar, gondola) Figure 4 Diagrammatic representation of a swing 3.18 i n f l a t a b l e a c t i v i t y t o y activity toy, with a structure made of flexible material, inflated by air, intended for children to play on or in EXAMPLE Bouncy castle, inflatable slides (see Figure 5). Note 1 to en

43、try: There are two types of inflatable activity toys: one is kept inflated by a closure (valve) once inflated; the other is kept inflated only by the continuous input of air from a blower. F i g u r e 5 E x a m p l e s o f i n f l a t a b l e a c t i v i t y t o y s ISO 2014 All rights reserved 5 IS

44、O 8124-4:2014(E) 3.19 paddling pool toy pool with a maximum depth of water of 400 mm measured between the overflow level and the deepest point within the pool Note 1 to entry: A permanently installed pool would not be considered to be a toy. Note 2 to entry: Examples of typical paddling pools can be

45、 found in the guidance document on the application of the European directive on the safety of toys (2009/48/EC), (h t t p:/e c . e u r o p a . eu/enterprise/sectors/toys/ files/gd_doc8pools_en.pdf). 4 Requirements 4.1 General See A.4.1. 4.1.1 Static strength Activity toys, other than swings, shall n

46、ot collapse when tested in accordance with 6.2.1 (strength of toys other than swings). After testing, the toy shall continue to comply with the relevant requirements of this part of ISO 8124. Requirements for swings are given in 4.7 (swings). 4.1.2 Maximum height See A.4.1.2. There shall be no part

47、of the activity toy designed to encourage the child to climb, sit on or stand on, with a height of 2 500 mm or more when measured from the ground. This does not include barriers, roofs, etc., that are not intended to be climbed, sat on or stood on. Barriers, roofs, etc., that are not intended to be

48、climbed shall be designed in such a way that climbing is not encouraged. 4.1.3 Corners and edges See A.4.1.3. Exposed corners and edges shall be rounded. Corners and exposed edges on moving parts shall have a minimum radius of 3 mm. This does not apply to swing elements with a mass of 1 000 g or les

49、s, the corners and edges of which shall be rounded. 4.1.4 Protruding parts 4.1.4.1 General Protruding parts (such as bolt ends and nuts) shall be recessed or be protected in such a way that they do not constitute an entrapment hazard or other hazard to users. If protrusions cannot be placed within the 50 mm outside diameter test gauge defined in 6.7.1 (all protrusions), they are considered to be inaccessible and are exempted from these requirements (see Figure 6). Rope protrusions are specifically exempted