ISO 3684 AMD 1-2006 Conveyor belts - Determination of minimum pulley diameters Amendment 1《传送带 皮带轮最小直径的测定 修改件1》.pdf

《ISO 3684 AMD 1-2006 Conveyor belts - Determination of minimum pulley diameters Amendment 1《传送带 皮带轮最小直径的测定 修改件1》.pdf》由会员分享，可在线阅读，更多相关《ISO 3684 AMD 1-2006 Conveyor belts - Determination of minimum pulley diameters Amendment 1《传送带 皮带轮最小直径的测定 修改件1》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、 Reference number ISO 3684:1990/Amd.1:2006(E) ISO 2006INTERNATIONAL STANDARD ISO 3684 Second edition 1990-03-15 AMENDMENT 1 2006-01-15 Conveyor belts Determination of minimum pulley diameters AMENDMENT 1 Courroies transporteuses Dtermination des diamtres minimaux des tambours AMENDEMENT 1 ISO 3684:1

2、990/Amd.1:2006(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downl

3、oading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the

4、General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address g

5、iven below. ISO 2006 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs memb

6、er body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2006 All rights reservedISO 3684:1990/Amd.1:2006(E) ISO 2006 All rights reserved iii Fo

7、reword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a tec

8、hnical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters o

9、f electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated

10、to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible fo

11、r identifying any or all such patent rights. Amendment 1 to ISO 3684:1990 was prepared by Technical Committee ISO/TC 41, Pulleys and belts (including veebelts), Subcommittee SC 3, Conveyor belts. ISO 3684:1990/Amd.1:2006(E) ISO 2006 All rights reserved 1 Conveyor belts Determination of minimum pulle

12、y diameters AMENDMENT 1 Page 1, Clause 1 Insert the following as a new third paragraph: “It is not applicable to light conveyor belts as described in ISO 21183-1, Light conveyor belts Part 1: Principal characteristics and applications.” ISO 3684:1990/Amd.1:2006(E) ICS 53.040.20 Price based on 1 page ISO 2006 All rights reserved