ISO 3500 AMD 1-2010 Gas cylinders - Seamless steel CO2 cylinders for fixed fire-fighting installations on ships Amendment 1《气瓶 船舶上安装的固定式防火用CO2无缝钢气瓶 修改件1》.pdf

《ISO 3500 AMD 1-2010 Gas cylinders - Seamless steel CO2 cylinders for fixed fire-fighting installations on ships Amendment 1《气瓶 船舶上安装的固定式防火用CO2无缝钢气瓶 修改件1》.pdf》由会员分享，可在线阅读，更多相关《ISO 3500 AMD 1-2010 Gas cylinders - Seamless steel CO2 cylinders for fixed fire-fighting installations on ships Amendment 1《气瓶 船舶上安装的固定式防火用CO2无缝钢气瓶 修改件1》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、 Reference number ISO 3500:2005/Amd.1:2010(E) ISO 2010INTERNATIONAL STANDARD ISO 3500 Third edition 2005-11-01 AMENDMENT 1 2010-05-01 Gas cylinders Seamless steel CO 2cylinders for fixed fire-fighting installations on ships AMENDMENT 1 Bouteilles gaz Bouteilles CO 2en acier, sans soudure, pour insta

2、llations fixes de lutte contre lincendie bord des navires AMENDEMENT 1 ISO 3500:2005/Amd.1:2010(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedd

3、ed are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. D

4、etails of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a proble

5、m relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2010 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, includi

6、ng photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published

7、 in Switzerland ii ISO 2010 All rights reservedISO 3500:2005/Amd.1:2010(E) ISO 2010 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is no

8、rmally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in

9、 the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepa

10、re International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that so

11、me of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Amendment 1 to ISO 3500:2005 was prepared by Technical Committee ISO/TC 58, Gas cylinders, Subcommittee SC 3, Cylinder design. ISO 3500:2005/Amd.1

12、:2010(E) ISO 2010 All rights reserved 1Gas cylinders Seamless steel CO 2cylinders for fixed fire-fighting installations on ships AMENDMENT 1 Page 2, immediately before 4.2 Insert the following new subclause: 4.1.3 Cylinders in this service are subject to extreme corrosion due to their exposure to saline conditions. It is common practice to allow an additional thickness as corrosion allowance for such cylinders. ISO 3500:2005/Amd.1:2010(E) ICS 13.220.10; 23.020.30; 47.020.99 Price based on 1 page ISO 2010 All rights reserved