ISO 29472 AMD 1-2014 Thermal insulating products for building applications - Determination of dimensional stability under specified temperature and humidity con.pdf

《ISO 29472 AMD 1-2014 Thermal insulating products for building applications - Determination of dimensional stability under specified temperature and humidity con.pdf》由会员分享，可在线阅读，更多相关《ISO 29472 AMD 1-2014 Thermal insulating products for building applications - Determination of dimensional stability under specified temperature and humidity con.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、 ISO 2014 Thermal insulating products for building applications Determination of dimensional stability under specified temperature and humidity conditions AMENDMENT 1 Produits isolants thermiques destins aux applications du btiment Dtermination de la stabilit dimensionnelle dans des conditions de te

2、mprature et dhumidit spcifies AMENDEMENT 1 INTERNATIONAL STANDARD ISO 29472 First edition 2008-11-01 Reference number ISO 29472:2008/Amd.1:2014(E) AMENDMENT 1 2014-12-01 ISO 29472:2008/Amd.1:2014(E)ii ISO 2014 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2014 All rights reserved. Unless othe

3、rwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address

4、below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ISO 29472:2008/Amd.1:2014(E) Foreword ISO (the International Organization fo

5、r Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the

6、 right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The proce

7、dures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editoria

8、l rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights

9、identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explan

10、ation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information The committee responsible for this docum

11、ent is ISO/TC 163, Thermal performance and energy use in the built environment, Subcommittee SC 1, Test and measurement methods. ISO 2014 All rights reserved iii ISO 29472:2008/Amd.1:2014(E)iv ISO 2014 All rights reserved Thermal insulating products for building applications Determination of dimensi

12、onal stability under specified temperature and humidity conditions AMENDMENT 1 Page V, Introduction Replace the existing Introduction with the following: This International Standard comprises the original EN 1604:1996 and EN 1604:1996/AC:1997 prepared by Technical Committee CEN/TC 88, Thermal insula

13、ting materials and products, which have been amended by ISO/TC 163/SC 1 with reference to conditioning and testing conditions in tropical countries. This International Standard is one of a series of documents specifying test methods, based on existing European Standards, that are being adopted by IS

14、O. This “package” of standards includes the following group of interrelated documents. ISO standard Title Respective EN standard ISO 12344 Thermal insulating products for building applications Determination of bending behaviour EN 12089 ISO 12968 Thermal insulation products for building applications

15、 Determination of the pull-off resistance of external thermal insulation composite sys- tems (ETICS) (foam block test) EN 13495 ISO 29465 Thermal insulating products for building applications Determination of length and width EN 822 ISO 29466 Thermal insulating products for building applications Det

16、ermination of thickness EN 823 ISO 29467 Thermal insulating products for building applications Determination of squareness EN 824 ISO 29468 Thermal insulating products for building applications Determination of flatness EN 825 ISO 29469 Thermal insulating products for building applications Determina

17、tion of compression behaviour EN 826 ISO 29470 Thermal insulating products for building applications Determination of the apparent density EN 1602 ISO 29471 Thermal insulating products for building applications Determination of dimensional stability under constant normal laboratory conditions (23 de

18、grees C/50 % relative humidity or in tropical countries 27 C/65 % relative humidity) EN 1603 ISO 29472 Thermal insulating products for building applications Determination of dimensional stability under specified temperature and humidity con- ditions EN 1604 ISO 29472:2008/Amd.1:2014(E) ISO 2014 All

19、rights reserved 1 ISO 29472:2008/Amd.1:2014(E) ISO standard Title Respective EN standard ISO 29764 Thermal insulating products for building applications Determination of deformation under specified compressive load and temperature condi- tions EN 1605 ISO 29765 Thermal insulating products for buildi

20、ng applications Determination of tensile strength perpendicular to faces EN 1607 ISO 29766 Thermal insulating products for building applications Determination of tensile strength parallel to faces EN 1608 ISO 29767 Thermal insulating products for building applications Determination of short-term wat

21、er absorption by partial immersion EN 1609 ISO 29768 Thermal insulating products for building applications Determination of linear dimensions of test specimens EN 12085 ISO 29769 Thermal insulating products for building applications Determination of behaviour under point load EN 12430 ISO 29770 Ther

22、mal insulating products for building applications Determination of thickness for floating-floor insulating products EN 12431 ISO 29771 Thermal insulating materials for building applications Determination of organic content EN 13820 ISO 29803 Thermal insulation products for building applications Dete

23、rmination of the resistance to impact of external thermal insulation composite systems (ETICS) EN 13497 ISO 29804 Thermal insulation products for building applications Determination of the tensile bond strength of the adhesive and of the base coat to the thermal insulation material EN 13494 ISO 2980

24、5 Thermal insulation products for building applications Determination of the mechanical properties of glass fibre meshes EN 13496 ISO 16534 Thermal insulating products for building applications Determination of compressive creep EN 1606 ISO 16535 Thermal insulating products for building applications

25、 Determination of long-term water absorption by immersion EN 12087 ISO 16536 Thermal insulating products for building applications Determination of long-term water absorption by diffusion EN 12088 ISO 16537 Thermal insulating products for building applications Determination of shear behaviour EN 120

26、90 ISO 16544 Thermal insulating products for building applications Conditioning to moisture equilibrium under specified temperature and humidity condi- tions EN 12429 ISO 16545 Thermal insulating products for building applications Determination of behaviour under cyclic loading EN 13793 ISO 16546 Th

27、ermal insulating products for building applications Determination of freezethaw resistance EN 120912 ISO 2014 All rights reserved ISO 29472:2008/Amd.1:2014(E) A further series of existing European Standards on test methods for products used to insulate building equipment and industrial installations

28、 was adopted by ISO. This “package” of standards comprises the following group of interrelated standards: ISO standard Title Respective EN standard ISO 12623 Thermal insulating products for building equipment and industrial installations Determination of short-term water absorption by partial immers

29、ion of preformed pipe insulation EN 13472 ISO 12624 Thermal insulation products Determination of trace quantities of water soluble chloride, fluoride, silicate, sodium ions and pH EN 13468 ISO 12628 Thermal insulating products for building equipment and industrial installations Determination of dime

30、nsions, squareness and linearity of preformed pipe insulation EN 13467 ISO 12629 Thermal insulating products for building equipment and industrial installations Determination of water vapour transmission properties of preformed pipe insulation EN 13469 ISO 18096 Thermal insulating products for build

31、ing equipment and industrial installations Determination of maximum service temperature for preformed pipe insulation EN 14707 ISO 18097 Thermal insulating products for building equipment and industrial installations Determination of maximum service temperature EN 14706 ISO 18098 Thermal insulating

32、products for building equipment and industrial installations Determination of the apparent density of preformed pipe insulation EN 13470 ISO 18099 Thermal insulating products for building equipment and industrial installations Determination of the coefficient of thermal expansion EN 13471 The Applic

33、ation of Agreement on technical cooperation between ISO and CEN (Vienna Agreement), Modes 1, 2, 4, and 5, was not approved by CEN/TC 88 and the necessity not seen by its stakeholders. Page 4, subclause 7.2 Add the second sentence to the existing paragraph: 7.2.5 Remove the specimens after exposure t

34、o the test atmosphere and expose them for a further (3 1) h at (23 2) C and (50 5) % relative humidity. In tropical countries, the temperature and humidity can be (27 2) C and (65 5) % relative humidity and this shall be stated clearly in the test report. ISO 2014 All rights reserved 3 ISO 29472:2008/Amd.1:2014(E) ISO 2014 All rights reserved ICS 91.100.60 Price based on 3 pages