ISO 2730-1973 Woodworking tools Wooden bodied planes《木工工具 木体刨》.pdf

《ISO 2730-1973 Woodworking tools Wooden bodied planes《木工工具 木体刨》.pdf》由会员分享，可在线阅读，更多相关《ISO 2730-1973 Woodworking tools Wooden bodied planes《木工工具 木体刨》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、INTERNATIONAL STANDARD INTERNATIONAL ORGANIZATION FOR STANDARDIZATION l MEXflYHAPOAHA5I OPI-AHW3ALWl I-IO AHAAPTM3AIJMM l ORGANIZATION INTERNATIONALE DE NORMALISATION Woodworking tools - Wooden bodied planes First edition - 1973-02-15 UDC 621.911.2 Descriptors : tools, hand tools, wood working, plan

2、ers, characteristics. Ref. No. IS0 2730-1973 (E) Price based on 4 pages Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-FOREWORD IS0 (the International Organization for S

3、tandardization) is a worldwide federation of national standards institutes (IS0 Member Bodies). The work of developing International Standards is carried out through IS0 Technical Committees. Every Member Body interested in a subject for which a Technical Committee has been set up has the right to b

4、e represented on that Committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. Draft International Standards adopted by the Technical Committees are circulated to the Member Bodies for approval before their acceptance as Internationa

5、l Standards by the IS0 Council. International Standard IS0 2730 was drawn up by Technical Committee lSO/TC 29, Small tools, and circulated to the Member Bodies in March 1972. It has been approved by the Member Bodies of the following countries : Austria Hungary Belgium India Canada Ireland Czechoslo

6、vakia Israel Egypt, Arab Rep. of Italy France Romania South Africa, Rep. of Spain Sweden Thailand Turkey United Kingdom No Member Body expressed disapproval of the document. 0 International Organization for Standardization, 1973 o Printed in Switzerland Copyright International Organization for Stand

7、ardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-INTERNATIONAL STANDARD IS0 2730-1973 (E) Woodworking tools - Wooden bodied planes 1 SCOPE AND FIELD OF APPLICATION This International Standard specifies the characteris

8、tics of wooden bodied planes. 2 REFERENCE IS0 2728, Woodworking too/s - Plane irons. 1) 3 NOMENCLATURE Type Figures Try plane Detail A Jack plane 1) At present at the stage of draft. 1 Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo rep

9、roduction or networking permitted without license from IHS-,-,-IS0 27304973 (E) without ramshorn Smoothing plane Number Denomination 1 Body 2 Sole 3 Nose 4 Heel 5 Box 6 Cheeks 7 Mouth 8 Handle 9 Hand protector 10 Ramshorn handle 11 Wedge 12 Clearance 13 Cut iron 14 Cw iron Copyright International Or

10、ganization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-IS0 2730-1973 (E) 4 DIMENSIONS 4.2 Jack plane Copyright International Organization for Standardization Provided by IHS under license with ISONot for

11、 ResaleNo reproduction or networking permitted without license from IHS-,-,-IS0 2730-1973 (E) 5 TECHNICAL SPECIFICATIONS 5.4 Clearance 5.1 Shape Wooden bodied planes shall have dimensions in conformity with those shown in section 4 and be well adapted in their shape to be firmly held during operatio

12、n. 5.2 Material The body of the plane shall be manufactured from an even-textured wood capable of sliding easily on the surface to be planed, and with a hardness sufficient to avoid rapid deterioration of the sole in operation. It is recommended that beech or a similar species be used. The body may

13、be made of two different timbers, well glued together, with a very hard quality for the sole to reduce wear during use. The wood shall be well seasoned (10 to 12 % moisture content) to avoid warping in normal use. It shall be without defects (knots, splits or splinters). After wedging the cu t and c

14、ap irons in place at the mouth shall be between 0 ,5 and 2 mm. 5.5 Box The shav inside ,ings ca of the box shall be smooth y finished tching and collecting in this part durin 5.6 Wedge , the clear The shape of the front part of the wedge be such that the shavings flow easily. 5.7 Finish to prevent g

15、 use. in particular shall The body shall be impregnated with a product (for example linseed oil) or coated with coiourless varnish to ensure that it remains dry under all conditions, 5.8 Cut iron and cap iron See IS0 2728. 5.3 Sole The sole shall be smooth and flat. The nose shal I not have the surf

16、ace to be pla ned. sharp corners which can dig into Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-This page intentionally left blank Copyright International Organizatio

17、n for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-This page intentionally left blank Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-