ISO 17231-2006 Leather - Physical and mechanical tests - Determination of water repellency of garment leather《皮革 物理和机械试验 服饰皮革的拒水性测定》.pdf

《ISO 17231-2006 Leather - Physical and mechanical tests - Determination of water repellency of garment leather《皮革 物理和机械试验 服饰皮革的拒水性测定》.pdf》由会员分享，可在线阅读，更多相关《ISO 17231-2006 Leather - Physical and mechanical tests - Determination of water repellency of garment leather《皮革 物理和机械试验 服饰皮革的拒水性测定》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、 Reference numberISO 17231:2006(E)IULTCS/IUP 37:2006(E)ISO 2006INTERNATIONAL STANDARD ISO17231IULTCS/IUP37First edition2006-09-15Leather Physical and mechanical tests Determination of water repellency of garment leather Cuir Essais physiques et mcaniques Dtermination de la rsistance au mouillage sup

2、erficiel des cuirs pour vtements ISO 17231:2006(E) IULTCS/IUP 37:2006(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and ins

3、talled on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software pro

4、ducts used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found,

5、 please inform the Central Secretariat at the address given below. ISO 2006 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in wr

6、iting from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2006 All rights reservedISO 1723

7、1:2006(E) IULTCS/IUP 37:2006(E) ISO 2006 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical co

8、mmittees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with th

9、e International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft Internati

10、onal Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be

11、the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 17231 was prepared by the Physical Test Commission of the International Union of Leather Technologists and Chemists Societies (IUP Commission, IULTCS) in collaboration with the European

12、 Committee for Standardization (CEN) Technical Committee CEN/TC 289 Leather, the secretariat of which is held by UNI. It was published as EN 14340. It is based on IUP 37 published in J. Soc. Leather Tech. Chem., 86 (7), p. 339, 2002, and declared an official method of the IULTCS in May 2003. IULTCS,

13、 originally formed in 1897, is a world-wide organization of professional leather societies to further the advancement of leather science and technology. IULTCS has three Commissions, which are responsible for establishing international methods for the sampling and testing of leather. ISO recognizes

14、IULTCS as an international standardizing body for the preparation of test methods for leather. INTERNATIONAL STANDARD ISO 17231:2006(E)IULTCS/IUP 37:2006(E) ISO 2006 All rights reserved 1Leather Physical and mechanical tests Determination of water repellency of garment leather 1 Scope This Internati

15、onal Standard specifies a method for determining the repellency of leather to surface wetting. It is applicable to all leathers intended for use in clothing. The method does not determine the resistance of leather to water penetration. 2 Normative references The following referenced documents are in

16、dispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 2418, Leather Chemical physical and mechanical and fastness tests Sampling location IS

17、O 2419, Leather Physical and mechanical tests Sample preparation and conditioning ISO 3696, Water for analytical laboratory use Specification and test methods 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 spray rating measure of the resista

18、nce of the surface of a leather to wetting 4 Principle A specified volume of distilled or deionized water is sprayed onto a test piece, which has been mounted on a ring and placed at an angle of 45 so that the centre of the test piece is at a specified distance below the spray nozzle. The spray rati

19、ng is determined by comparing the appearance of the test piece with descriptive and photographic standards. The mass of water absorbed by the test piece is determined by weighing before and after applying the water spray. ISO 17231:2006(E) IULTCS/IUP 37:2006(E) 2 ISO 2006 All rights reserved5 Appara

20、tus 5.1 Spray device, as shown in Figure 1, consisting of a funnel, diameter 150 mm 2 mm, held vertically with a metal spray nozzle (5.2) connected to the end of the stem by flexible tubing of bore about 10 mm. The overall distance from the top of the funnel to the bottom of the nozzle is 190 mm 2 m

21、m. Dimensions in millimetres Key 1 glass funnel 150 2 2 ring support 3 rubber tubing 4 spray nozzle 5 stand 6 specimen 7 specimen holder 8 support (e.g. wood) Figure 1 Apparatus for spray test ISO 17231:2006(E) IULTCS/IUP 37:2006(E) ISO 2006 All rights reserved 35.2 Metal spray nozzle, as shown in F

22、igure 2, with approximate diameter of 33 mm, having a convex face with 19 holes of 0,9 mm 0,05 mm diameter distributed over the face of the nozzle. The duration of flow for 250 ml 5 ml of distilled or deionized water poured into the funnel shall be 27,5 s 2,5 s. Dimensions in millimetres Key 1 12 ho

23、les 0,9 0,05 on a circle 21,4 0,05 2 6 holes 0,9 0,05 on a circle 10 0,05 3 1 hole 0,9 0,05 on centre Figure 2 Spray nozzle 5.3 Test piece holder, consisting of two metal rings which fit into each other. The inner ring is fixed and of outside diameter 150 mm 2 mm. The outer ring is adjustable so tha

24、t the internal diameter can be reduced to 150 mm to allow the test piece to be securely clamped between the two rings. When in position for test, the rings rest on a suitable support so that the test piece is at an angle of 45,0 2,5 and with the centre of the clamped area 150 mm 2 mm below the centr

25、e of the face of the metal nozzle. 5.4 Balance, reading to 0,001 g. 5.5 Distilled or deionized water, conforming to the requirements of grade 3 of ISO 3696. 6 Sampling and sample preparation 6.1 Sample in accordance with ISO 2418. Cut three square test pieces of side 182 mm 2 mm ensuring that they a

26、re taken from areas free from any holes or other damage. NOTE 1 It may be necessary to trim the wool if a woolled sheepskin is being tested to allow secure clamping of the test piece. NOTE 2 If there is a requirement for more than two hides or skins to be tested in one batch, then only one sample ne

27、ed be taken from each hide or skin, provided that the overall total is not less than three test pieces. 6.2 Condition the test pieces in accordance with ISO 2419. 6.3 Weigh the test piece to the nearest 0,001 g. 6.4 Carry out all further operations at a temperature of 20 C 2 C or 23 C 2 C. There is

28、no need for further humidity control. ISO 17231:2006(E) IULTCS/IUP 37:2006(E) 4 ISO 2006 All rights reserved7 Procedure 7.1 Mount the test piece securely on the test piece holder (5.3) with the face of the leather which would be exposed in wear uppermost. Place the test piece holder in position belo

29、w the spray nozzle. 7.2 Pour 250 ml 5 ml of distilled or deionized water (5.5) at the controlled temperature (6.4) into the funnel quickly but steadily so that the spraying is continuous once it has commenced. 7.3 Immediately after the spraying has ceased, remove the holder and test piece and tap tw

30、o diametrically opposite points of the frame against a solid object, with the plane of the leather almost horizontal and the tested surface downwards. 7.4 Assign to the test piece the spray rating on either the following descriptive scale or the photographic scale in Annex A which best describes the

31、 degree of wetting. Intermediate ratings are not to be attempted. 1 Wetting of the whole of the sprayed surface. 2 Wetting of half of the sprayed surface. This usually occurs through the merging of small, discrete wetted areas. 3 Wetting of the sprayed surface only as small discrete areas. 4 No wett

32、ing of, but adherence of small drops to, the sprayed surface. 5 No wetting of and no adherence of small drops to the sprayed surface. 7.5 Examine the reverse side of the test piece and note any wetting. 7.6 Remove the test piece from the holder, blot gently to remove any water droplets which still a

33、dhere and re-weigh to the nearest 0,001 g. 8 Expression of results Calculate the mass of water absorbed, mw, in grams and the percentage of water absorbed, w, using the equations: w21mmm=211()100 %mmwm= where m1is the initial mass of the test piece, in grams; m2is the mass of the test piece after th

34、e test, in grams. ISO 17231:2006(E) IULTCS/IUP 37:2006(E) ISO 2006 All rights reserved 59 Test report The test report shall include the following for each test piece: a) a reference to this International Standard; i.e. 17231:2006; b) the spray rating (7.4); c) the mass of water absorbed, mw,in grams

35、; d) the percentage of water absorbed, w; e) the standard atmosphere used for conditioning and testing as given in ISO 2419 (i.e. 20 C/65 % RH, or 23 C/50 % RH); f) any deviations from the method specified in this International Standard; g) full details for identification of the sample and any devia

36、tions from ISO 2418 with respect to sampling. ISO 17231:2006(E) IULTCS/IUP 37:2006(E) 6 ISO 2006 All rights reservedAnnex A (normative) ISO photographic scale Figure A.1 ISO spray test rating chart based on the American Association of Textile Chemists and Colorists (AATCC) photographic scale NOTE Th

37、e ISO descriptive scale corresponds to the AATCC photographic scale as follows: ISO 1 = AATCC 50 Wetting of the whole of the sprayed surface. ISO 2 = AATCC 70 Wetting of half of the sprayed surface. This usually occurs through the merging of small, discrete wetted areas. ISO 3 = AATCC 80 Wetting of

38、the sprayed surface only as small discrete areas. ISO 4 = AATCC 90 No wetting of, but adherence of small drops to, the sprayed surface. ISO 5 = AATCC 100 No wetting of and no adherence of small drops to the sprayed surface. ISO 17231:2006(E) IULTCS/IUP 37:2006(E) ISO 2006 All rights reserved 7Annex

39、B (informative) Sources of apparatus Examples of suitable products available commercially are given below. The recommended apparatus is the spray rating tester, manufactured, for example by: James H. Heal and Co. Ltd1), Richmond Works, Halifax, West Yorkshire, HX3 6EP, England; SDL International Ltd

40、1), PO Box 162, Crown Royal, Shawcross St., Stockport, SKI 3JW, England. Copies of the AATCC Standard Spray Test Ratings Chart may be obtained from the American Association of Textile Chemist and Colorists, P O Box 12215, Research Triangle Park, NC 27709, USA. 1) James H. Heal and Co. Ltd and SDL In

41、ternational Ltd are an examples of suppliers of a suitable products available commercially. This information is given for the convenience of users of this International Standard and does not constitute an endorsement by ISO of their products. ISO 17231:2006(E) IULTCS/IUP 37:2006(E) ICS 59.140.30 Price based on 7 pages ISO 2006 All rights reserved