ISO 16145-2-2012 Ships and marine technology - Protective coatings and inspection method - Part 2 Void spaces of bulk carriers and oil tankers《船舶和海洋技术 防护涂层和检验方法.pdf
《ISO 16145-2-2012 Ships and marine technology - Protective coatings and inspection method - Part 2 Void spaces of bulk carriers and oil tankers《船舶和海洋技术 防护涂层和检验方法.pdf》由会员分享,可在线阅读,更多相关《ISO 16145-2-2012 Ships and marine technology - Protective coatings and inspection method - Part 2 Void spaces of bulk carriers and oil tankers《船舶和海洋技术 防护涂层和检验方法.pdf(46页珍藏版)》请在麦多课文档分享上搜索。
1、 ISO 2012 Ships and marine technology Protective coatings and inspection method Part 2: Void spaces of bulk carriers and oil tankers Navires et technologie maritime Revtements de protection et mthode dinspection Partie 2: Espaces vides de vraquiers et de rservoirs dhuile INTERNATIONAL STANDARD ISO 1
2、6145-2 First edition 2012-10-01 Reference number ISO 16145-2:2012(E) ISO 16145-2:2012(E) ii ISO 2012 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2012 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, elect
3、ronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.o
4、rg Web www.iso.org Published in Switzerland ISO 16145-2:2012(E) ISO 2012 All rights reserved iii Contents Page Foreword iv Introduction v 1 Scope 1 2 Normative references . 1 3 T erms and definitions . 2 4 Symbols and abbreviated terms . 3 4.1 Symbols . 3 4.2 Abbreviated terms . 3 5 General procedur
5、es for coating work 3 6 Standard for coating work 4 6.1 Areas considered 4 6.2 Surface preparation 6 6.3 Primary surface preparation and shop priming 8 6.4 Secondary surface preparation . 9 6.5 Coating .10 6.6 Treatment for coating defects 13 7 Inspection 14 7.1 Inspection procedure .14 7.2 Coating
6、inspection 14 7.3 Dry film thickness measurement 16 Annex A (informative) Measurement of the conductivity for abrasives .21 Annex B (informative) Measurement of water soluble salt23 Annex C (informative) Inspection items and management of inspection .25 Annex D (informative) Standard for coating tec
7、hnical file (CTF) .29 Bibliography .38 ISO 16145-2:2012(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committ
8、ees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the Int
9、ernational Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International
10、Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the s
11、ubject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 16145-2 was prepared by Technical Committee ISO/TC 8, Ships and marine technology, Subcommittee SC 8, Ship design. ISO 16145 consists of the following parts, under the general title Ships an
12、d marine technology Protective coatings and inspection method: Part 1: Dedicated sea water ballast tanks Part 2: Void spaces of bulk carriers and oil tankers Part 3: Cargo oil tanks of crude oil tankers The following parts are under preparation: Part 4: Automated measuring method for the total amoun
13、t of water-soluble salts Part 5: Assessment method for coating damages iv ISO 2012 All rights reserved ISO 16145-2:2012(E) Introduction The ISO 16145 series addresses qualified coating and inspection works in accordance with the requirements of IMO PSPC. Technical Committee ISO/TC 8, Ships and marin
14、e technology, SC 8, Ship design has decided to standardize a coating and inspection method for the IMO PSPC series. Coating quality itself depends largely on the surface preparation and coating application. Therefore, the right application of surface preparation and coating in accordance with the co
15、ating manufacturers recommendations, including inspections at each step, are of vital importance. This part of ISO 16145 is intended to serve as a standard for ship owners, shipyards, coating manufacturers, coating inspectors and coating applicators in applying IMO PSPC in the new building stage. IS
16、O 2012 All rights reserved v Ships and marine technology Protective coatings and inspection method Part 2: Void spaces of bulk carriers and oil tankers 1 Scope This part of ISO 16145 specifies a method of protective coatings and its inspection of void spaces of bulk carriers and oil tankers which ar
17、e contracted and agreed to apply PSPC/VOID IMO Res.MSC.244 (83) for new building on or after 5 October 2007. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edit
18、ion cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 8501-1:2007, Preparation of steel substrates before application of paints and related products Visual assessment of surface cleanliness Part 1: Rust grades and preparation
19、 grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings ISO 8501-3:2001 1) , Preparation of steel substrates before application of paints and related products Visual assessment of surface cleanliness Part 3: Preparation grades of welds, cut edges and o
20、ther areas with surface imperfections ISO 8502-3:1992, Preparation of steel substrates before application of paints and related products Tests for the assessment of surface cleanliness Part 3: Assessment of dust on steel surfaces prepared for painting (pressure-sensitive tape method) ISO 8502-9:1998
21、, Preparation of steel substrates before application of paints and related products Tests for the assessment of surface cleanliness Part 9: Field method for the conductometric determination of water- soluble salts ISO 8503-1:2012, Preparation of steel substrates before application of paints and rela
22、ted products Surface roughness characteristics of blast-cleaned steel substrates Part 1: Specifications and definitions for ISO surface profile comparators for the assessment of abrasive ISO 8503-2:2012, Preparation of steel substrates before application of paints and related products Surface roughn
23、ess characteristics of blast-cleaned steel substrates Part 2: Method for the grading of surface profile of abrasive blast-cleaned steel Comparator procedure IACS UI SC223, For Application of SOLAS Regulation II-1/3-2 Performance Standard for Protective Coatings (PSPC) for Dedicated Seawater Ballast
24、Tanks in All Types of Ships and Double-side Skin Spaces of Bulk Carriers, adopted by Resolution MSC.215 (82) IMO Res.MSC.244 (83), Performance standard for protective coatings for void spaces on bulk carriers and oil tankers 1) Withdrawn International Standard revised by ISO 8501-3:2006. INTERNATION
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO1614522012SHIPSANDMARINETECHNOLOGYPROTECTIVECOATINGSANDINSPECTIONMETHODPART2VOIDSPACESOFBULKCARRIERSANDOILTANKERS

链接地址:http://www.mydoc123.com/p-1251527.html