IEEE C57 12 01-2015 en General Requirements for Dry-Type Distribution and Power Transformers《干式配电和电力变压器的一般技术要求》.pdf
《IEEE C57 12 01-2015 en General Requirements for Dry-Type Distribution and Power Transformers《干式配电和电力变压器的一般技术要求》.pdf》由会员分享,可在线阅读,更多相关《IEEE C57 12 01-2015 en General Requirements for Dry-Type Distribution and Power Transformers《干式配电和电力变压器的一般技术要求》.pdf(52页珍藏版)》请在麦多课文档分享上搜索。
1、 IEEE Standard for General Requirements for Dry-Type Distribution and Power Transformers Sponsored by the Transformers Committee IEEE 3 Park Avenue New York, NY 10016-5997 USA IEEE Power and Energy Society IEEE Std C57.12.01-2015 (Revision of IEEE Std C57.12.01-2005) IEEE Std C57.12.01-2015 (Revisio
2、n of IEEE Std C57.12.01-2005) IEEE Standard for General Requirements for Dry-Type Distribution and Power Transformers Sponsor Transformers Committee of the IEEE Power and Energy Society Approved 16 February 2015 IEEE-SA Standards Board Copyrights and Permissions: The IEEE thanks the International El
3、ectrotechnical Commission (IEC) for permission to reproduce Figure 2 from its International Standard IEC 60076-11 ed.1.0 (2004). All such extracts are copyright of IEC, Geneva, Switzerland. All rights reserved. Further information on the IEC is available from www.iec.ch. IEC has no responsibility fo
4、r the placement and context in which the extracts and contents are reproduced by the author, nor is IEC in any way responsible for the other content or accuracy therein. Abstract: Electrical and mechanical requirements of ventilated, non-ventilated, and sealed dry-type distribution and power transfo
5、rmers or autotransformers (single and polyphase, with a voltage of 601 V or higher in the highest voltage winding) are described. Keywords: autotransformer, distribution, dry-type, IEEE C57.12.01, power transformer, voltage, winding The Institute of Electrical and Electronics Engineers, Inc. 3 Park
6、Avenue, New York, NY 10016-5997, USA Copyright 2015 by The Institute of Electrical and Electronics Engineers, Inc. All rights reserved. Published 27 February 2015. Printed in the United States of America. IEEE is a registered trademark in the U.S. Patent fitness for a particular purpose; non-infring
7、ement; and quality, accuracy, effectiveness, currency, or completeness of material. In addition, IEEE disclaims any and all conditions relating to: results; and workmanlike effort. IEEE standards documents are supplied “AS IS” and “WITH ALL FAULTS.” Use of an IEEE standard is wholly voluntary. The e
8、xistence of an IEEE standard does not imply that there are no other ways to produce, test, measure, purchase, market, or provide other goods and services related to the scope of the IEEE standard. Furthermore, the viewpoint expressed at the time a standard is approved and issued is subject to change
9、 brought about through developments in the state of the art and comments received from users of the standard. In publishing and making its standards available, IEEE is not suggesting or rendering professional or other services for, or on behalf of, any person or entity nor is IEEE undertaking to per
10、form any duty owed by any other person or entity to another. Any person utilizing any IEEE Standards document, should rely upon his or her own independent judgment in the exercise of reasonable care in any given circumstances or, as appropriate, seek the advice of a competent professional in determi
11、ning the appropriateness of a given IEEE standard. IN NO EVENT SHALL IEEE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO: PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
12、 HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE PUBLICATION, USE OF, OR RELIANCE UPON ANY STANDARD, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE AND REGARDLESS OF WHETHER SUCH DAMAGE
13、 WAS FORESEEABLE. Translations The IEEE consensus development process involves the review of documents in English only. In the event that an IEEE standard is translated, only the English version published by IEEE should be considered the approved IEEE standard. Official Statements A statement, writt
14、en or oral, that is not processed in accordance with the IEEE-SA Standards Board Operations Manual shall not be considered or inferred to be the official position of IEEE or any of its committees and shall not be considered to be, or be relied upon as, a formal position of IEEE. At lectures, symposi
15、a, seminars, or educational courses, an individual presenting information on IEEE standards shall make it clear that his or her views should be considered the personal views of that individual rather than the formal position of IEEE. Comments on Standards Comments for revision of IEEE Standards docu
16、ments are welcome from any interested party, regardless of membership affiliation with IEEE. However, IEEE does not provide consulting information or advice pertaining to IEEE Standards documents. Suggestions for changes in documents should be in the form of a proposed change of text, together with
17、appropriate supporting comments. Since IEEE standards represent a consensus of concerned interests, it is important that any responses to comments and questions also receive the concurrence of a balance of interests. For this reason, IEEE and the members of its societies and Standards Coordinating C
18、ommittees are not able to provide an instant response to comments or questions except in those cases where the matter has previously been addressed. For the same reason, IEEE does not respond to interpretation requests. Any person who would like to participate in revisions to an IEEE standard is wel
19、come to join the relevant IEEE working group. Comments on standards should be submitted to the following address: Secretary, IEEE-SA Standards Board 445 Hoes Lane Piscataway, NJ 08854 USA Laws +1 978 750 8400. Permission to photocopy portions of any individual standard for educational classroom use
20、can also be obtained through the Copyright Clearance Center. Updating of IEEE Standards Documents Users of IEEE Standards documents should be aware that these documents may be superseded at any time by the issuance of new editions or may be amended from time to time through the issuance of amendment
21、s, corrigenda, or errata. An official IEEE document at any point in time consists of the current edition of the document together with any amendments, corrigenda, or errata then in effect. Every IEEE standard is subjected to review at least every ten years. When a document is more than ten years old
22、 and has not undergone a revision process, it is reasonable to conclude that its contents, although still of some value, do not wholly reflect the present state of the art. Users are cautioned to check to determine that they have the latest edition of any IEEE standard. In order to determine whether
23、 a given document is the current edition and whether it has been amended through the issuance of amendments, corrigenda, or errata, visit the IEEE-SA website at http:/ieeexplore.ieee.org/xpl/standards.jsp or contact IEEE at the address listed previously. For more information about the IEEE SA or IEE
24、Es standards development process, visit the IEEE-SA website at http:/standards.ieee.org. Errata Errata, if any, for all IEEE standards can be accessed on the IEEE-SA website at the following URL: http:/standards.ieee.org/findstds/errata/index.html. Users are encouraged to check this URL for errata p
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- IEEEC5712012015ENGENERALREQUIREMENTSFORDRYTYPEDISTRIBUTIONANDPOWERTRANSFORMERS 配电 电力变压器 一般 技术 要求 PDF

链接地址:http://www.mydoc123.com/p-1249158.html