IEEE C37 45-2016 en Design Test Specifications for High Voltage ( 1000 V) Distribution Class Enclosed Single-Pole Air Switches.pdf

《IEEE C37 45-2016 en Design Test Specifications for High Voltage ( 1000 V) Distribution Class Enclosed Single-Pole Air Switches.pdf》由会员分享，可在线阅读，更多相关《IEEE C37 45-2016 en Design Test Specifications for High Voltage ( 1000 V) Distribution Class Enclosed Single-Pole Air Switches.pdf（27页珍藏版）》请在麦多课文档分享上搜索。

1、IEEE Standard for Design Test Specifications for High Voltage ( 1000 V) Distribution Class Enclosed Single-Pole Air SwitchesIEEE Std C37.45-2016(Revision of IEEE Std C37.45-2007)IEEE Power and Energy SocietySponsored by the Switchgear CommitteeIEEE3 Park AvenueNew York, NY 10016-5997USAIEEE Std C37.

2、45-2016(Revision of IEEE Std C37.45-2007)IEEE Standard for Design Test Specifications for High Voltage ( 1000 V) Distribution Class Enclosed Single-Pole Air SwitchesSponsor Switchgear Committee of the IEEE Power and Energy SocietyApproved 15 May 2016IEEE-SA Standards BoardAbstract: Specifications fo

3、r high-voltage (above 1000 V) distribution class enclosed single-pole air switches and associated accessories with rated voltages from 1 kV through 8.3 kV are established. All of these devices are intended for use on alternating current distribution systems. These include distribution class enclosed

4、 single-pole air switches, supports, mountings, fuse hooks, and tongs, all of the type used exclusively with distribution class enclosed single-pole air switches, and distri-bution class enclosed single-pole air switches used in enclosure packages.Keywords: alternating current distribution systems,

5、distribution class enclosed single-pole air switches, enclosure packages, fuse hooks, IEEE C37.45, supports and mountings, tongsThe Institute of Electrical and Electronics Engineers, Inc.3 Park Avenue, New York, NY 10016-5997, USACopyright 2016 by The Institute of Electrical and Electronics Engineer

6、s, Inc. All rights reserved. Published 29 November 2016. Printed in the United States of America.IEEE is a registered trademark in the U.S. Patent fitness for a particular purpose; non-infringement; and quality, accuracy, effectiveness, currency, or completeness of material. In addition, IEEE discla

7、ims any and all conditions relating to: results; and workmanlike effort. IEEE standards documents are supplied “AS IS” and “WITH ALL FAULTS.”Use of an IEEE standard is wholly voluntary. The existence of an IEEE standard does not imply that there are no other ways to produce, test, measure, purchase,

8、 market, or provide other goods and services related to the scope of the IEEE standard. Furthermore, the viewpoint expressed at the time a standard is approved and issued is subject to change brought about through developments in the state of the art and comments received from users of the standard.

9、In publishing and making its standards available, IEEE is not suggesting or rendering professional or other services for, or on behalf of, any person or entity nor is IEEE undertaking to perform any duty owed by any other person or entity to another. Any person utilizing any IEEE Standards document,

10、 should rely upon his or her own independent judgment in the exercise of reasonable care in any given circumstances or, as appropri-ate, seek the advice of a competent professional in determining the appropriateness of a given IEEE standard.IN NO EVENT SHALL IEEE BE LIABLE FOR ANY DIRECT, INDIRECT,

11、INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO: PROCURE-MENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CON-TRACT, STRICT LIABILITY, OR TORT (INCLUDING NE

12、GLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE PUBLICATION, USE OF, OR RELIANCE UPON ANY STANDARD, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE AND REGARDLESS OF WHETHER SUCH DAMAGE WAS FORESEEABLE.4Copyright 2016 IEEE. All rights reserved.TranslationsThe IEEE consensus development proces

13、s involves the review of documents in English only. In the event that an IEEE standard is translated, only the English version published by IEEE should be considered the approved IEEE standard.Official statementsA statement, written or oral, that is not processed in accordance with the IEEE-SA Stand

14、ards Board Operations Manual shall not be considered or inferred to be the official position of IEEE or any of its committees and shall not be considered to be, or be relied upon as, a formal position of IEEE. At lectures, symposia, seminars, or educational courses, an individual presenting informat

15、ion on IEEE standards shall make it clear that his or her views should be considered the personal views of that individual rather than the formal position of IEEE.Comments on standardsComments for revision of IEEE Standards documents are welcome from any interested party, regardless of membership af

16、filiation with IEEE. However, IEEE does not provide consulting information or advice pertain-ing to IEEE Standards documents. Suggestions for changes in documents should be in the form of a proposed change of text, together with appropriate supporting comments. Since IEEE standards represent a conse

17、nsus of concerned interests, it is important that any responses to comments and questions also receive the concur-rence of a balance of interests. For this reason, IEEE and the members of its societies and Standards Coordi-nating Committees are not able to provide an instant response to comments or

18、questions except in those cases where the matter has previously been addressed. For the same reason, IEEE does not respond to interpretation requests. Any person who would like to participate in revisions to an IEEE standard is welcome to join the relevant IEEE working group.Comments on standards sh

19、ould be submitted to the following address:Secretary, IEEE-SA Standards Board445 Hoes LanePiscataway, NJ 08854 USALaws and regulationsUsers of IEEE Standards documents should consult all applicable laws and regulations. Compliance with the provisions of any IEEE Standards document does not imply com

20、pliance to any applicable regulatory require-ments. Implementers of the standard are responsible for observing or referring to the applicable regulatory requirements. IEEE does not, by the publication of its standards, intend to urge action that is not in compliance with applicable laws, and these d

21、ocuments may not be construed as doing soCopyrightsIEEE draft and approved standards are copyrighted by IEEE under US and international copyright laws. They are made available by IEEE and are adopted for a wide variety of both public and private uses. These include both use, by reference, in laws an

22、d regulations, and use in private self-regulation, standardization, and the pro-motion of engineering practices and methods. By making these documents available for use and adoption by public authorities and private users, IEEE does not waive any rights in copyright to the documents.5Copyright 2016

23、IEEE. All rights reserved.PhotocopiesSubject to payment of the appropriate fee, IEEE will grant users a limited, non-exclusive license to photocopy portions of any individual standard for company or organizational internal use or individual, non-commercial use only. To arrange for payment of licensi

24、ng fees, please contact Copyright Clearance Center, Customer Ser-vice, 222 Rosewood Drive, Danvers, MA 01923 USA; +1 978 750 8400. Permission to photocopy portions of any individual standard for educational classroom use can also be obtained through the Copyright Clearance Center.Updating of IEEE St

25、andards documentsUsers of IEEE Standards documents should be aware that these documents may be superseded at any time by the issuance of new editions or may be amended from time to time through the issuance of amendments, corri-genda, or errata. An official IEEE document at any point in time consist

26、s of the current edition of the document together with any amendments, corrigenda, or errata then in effect.Every IEEE standard is subjected to review at least every 10 years. When a document is more than 10 years old and has not undergone a revision process, it is reasonable to conclude that its co

27、ntents, although still of some value, do not wholly reflect the present state of the art. Users are cautioned to check to determine that they have the latest edition of any IEEE standard.In order to determine whether a given document is the current edition and whether it has been amended through the

28、 issuance of amendments, corrigenda, or errata, visit the IEEE Xplore at http:/ieeexplore.ieee.org/ or contact IEEE at the address listed previously. For more information about the IEEE-SA or IEEEs standards development process, visit the IEEE-SA Website at http:/standards.ieee.org.ErrataErrata, if

29、any, for all IEEE standards can be accessed on the IEEE-SA Website at the following URL: http:/standards.ieee.org/findstds/errata/index.html. Users are encouraged to check this URL for errata periodically.PatentsAttention is called to the possibility that implementation of this standard may require

30、use of subject matter covered by patent rights. By publication of this standard, no position is taken by the IEEE with respect to the existence or validity of any patent rights in connection therewith. If a patent holder or patent applicant has filed a statement of assurance via an Accepted Letter o

31、f Assurance, then the statement is listed on the IEEE-SA Website at http:/standards.ieee.org/about/sasb/patcom/patents.html. Letters of Assurance may indicate whether the Submitter is willing or unwilling to grant licenses under patent rights without compensation or under reasonable rates, with reas

32、onable terms and conditions that are demonstrably free of any unfair discrim-ination to applicants desiring to obtain such licenses.Essential Patent Claims may exist for which a Letter of Assurance has not been received. The IEEE is not re-sponsible for identifying Essential Patent Claims for which

33、a license may be required, for conducting inquiries into the legal validity or scope of Patents Claims, or determining whether any licensing terms or conditions provided in connection with submission of a Letter of Assurance, if any, or in any licensing agreements are reasonable or non-discriminator

34、y. Users of this standard are expressly advised that determination of the valid-ity of any patent rights, and the risk of infringement of such rights, is entirely their own responsibility. Further information may be obtained from the IEEE Standards Association6Copyright 2016 IEEE. All rights reserve

35、d.ParticipantsAt the time this IEEE standard was completed, the Revision of Fuse Specification Standards Working Group had the following membership:Mark W. Stavnes, ChairAlan Yeges, Vice ChairChris AmbroseGlenn R. BorchardtSam ChangSterlin CochranJonathan H. DeverickDavid L. FrischGary W. HaynesFran

36、k C. LambertJohn G. LeachChris LettowBrad LewisJames R. MarekSean W. MoodyR. Neville ParryElizondo RodolfoTimothy E. RoysterJon SpencerTom StefanskiWilliam WalterJim WenzelCharles WorthingtonThe following members of the individual balloting committee voted on this standard. Balloters may have voted

37、for approval, disapproval, or abstention.Chris AmbroseThomas BarnesCraig BefusGlenn BorchardtPaul CardinalEdgar DullniDonald DunnSergio FloresFredric FriendDavid GilmerMietek GlinkowskiRandall GrovesGary W. HaynesJeffrey HelzerRichard JacksonYuri KhersonskyJoseph L. KoepfingerBoris KoganJim Kulchisk

38、yFrank LambertBenjamin LanzJohn LeachSean W. MoodyDarryl MoserArthur NeubauerMichael NewmanT. W. OlsenLorraine PaddenK. James PhillipsCarl ReigartMichael RobertsCharles RogersTim RohrerJoseph RostronTimothy E. RoysterThomas RozekBartien SayogoJeremy SmithJerry SmithKirk SmithMark StavnesWayne StecTo

39、m StefanskiDavid TepenJohn VergisWilliam WalterJohn WangAlan YergesLarry YonceRichard YorkWhen the IEEE-SA Standards Board approved this standard on 15 May 2016, it had the following membership:Jean-Philippe Faure, ChairTed Burse, Vice ChairJohn D. Kulick, Past ChairKonstantinos Karachalios, Secreta

40、ryChuck AdamsMasayuki AriyoshiStephen DukesJianbin FanJ. Travis GriffithGary HoffmanRonald W. HotchkissMichael JanezicJoseph L. Koepfinger*Hung LingKevin LuAnnette D. ReillyGary RobinsonMehmet UlemaYingli WenHoward WolfmanDon WrightYu YuanDaidi Zhong*Member Emeritus7Copyright 2016 IEEE. All rights r

41、eserved.IntroductionThis introduction is not part of IEEE Std C37.452016, IEEE Standard for Design Test Specifications for High Voltage ( 1000 V) Distribution Class Enclosed Single-Pole Air Switches.This standard is a revision of IEEE Std C37.452007, to bring it up to date and in line with present-d

42、ay re-quirements for high-voltage switches. The definitions and testing requirements have been added to this new document so that it can be a stand-alone standard.8Copyright 2016 IEEE. All rights reserved.Contents1. Overview . 91.1 Scope 91.2 Purpose . 92. Normative references 93. Definitions . 104.

43、 Service conditions . 104.1 General . 104.2 For switches rated for use at a maximum application temperature of 40 C . 114.3 For switches rated for use at a maximum application temperature above 40 C . 115. General rating information 115.1 Ratings 115.2 Preferred ratings . 126. Type tests and specifi

44、cations 126.1 General . 126.2 Requirements for re-testing modified devices 136.3 Specifications . 137. Common test requirements 147.1 General . 147.2 Test values 147.3 Test site conditions . 157.4 Frequency and wave shape of test voltage 157.5 Devices to be tested 157.6 Acceptance criteria . 167.7 T

45、est conductor dimensions . 167.8 Mounting and grounding of the device for tests 168. Design test procedure requirements 178.1 Dielectric tests 178.2 Radio-influence tests 198.3 Short-time current tests . 218.4 Temperature-rise tests . 239. Construction requirements 2410. Nameplate marking requiremen

46、ts . 2411. Application requirements 2411.1 Load-break ability 2411.2 Load-making ability . 24Annex A (informative) Bibliography . 259Copyright 2016 IEEE. All rights reserved.1. Overview1.1 ScopeThis standard establishes design tests and specifications for high-voltage (above 1000 V) distribution cla

47、ss en-closed single-pole air switches and associated accessories with rated voltages up to 8.3 kV. All of these devices are intended for use on alternating current distribution systems. These design tests and specifications apply to the following specific types of equipment:a) Distribution class enc

48、losed single-pole air switchesb) Supports, mountings, fuse hooks, and tongs, all of the type used exclusively with distribution class enclosed single-pole air switchesc) Distribution class enclosed single-pole air switches used in enclosure packages1.2 PurposeThis standard contains the specification

49、s and minimum testing requirements for distribution class enclosed single-pole air switches with rated voltages up to 8.3 kV. Such standardization is needed to help ensure uni-form minimum product testing for devices within the document scope. Test areas covered are based on histor-ical experience.2. Normative referencesThe following referenced documents are indispensable for the application of this document (i.e., they must be understood and used, so each referenced document is cited in text and its relationship to this document is explained). For dated references, o