IEEE 315-1975 en Graphic Symbols for Electrical and Electronics Diagrams (Including Reference Designation Class Designation Letters) (CSA Z99-75 Includes supple.pdf

《IEEE 315-1975 en Graphic Symbols for Electrical and Electronics Diagrams (Including Reference Designation Class Designation Letters) (CSA Z99-75 Includes supple.pdf》由会员分享，可在线阅读，更多相关《IEEE 315-1975 en Graphic Symbols for Electrical and Electronics Diagrams (Including Reference Designation Class Designation Letters) (CSA Z99-75 Includes supple.pdf（453页珍藏版）》请在麦多课文档分享上搜索。

1、IEEE Std 315-1975 (Reaffirmed 1993)ANSI Y32.2-1975 (Reaffirmed 1989)CSA Z99-1975(Revision of IEEE Std 315-1971ANSI Y32.1-1972CSA Z99-1972)IEEE Standard American National Standard Canadian StandardGraphic Symbols for Electrical and Electronics Diagrams (Including Reference Designation Letters)Sponsor

2、IEEE Standards Coordinating Committee 11, Graphic Symbols Secretariat for American National Standards Committee Y32American Society of Mechanical EngineersInstitute of Electrical and Electronics EngineersApproved September 4, 1975Reaffirmed October 20, 1988Reaffirmed December 2, 1993IEEE Standards B

3、oardApproved October 31, 1975Reaffirmed January 16, 1989American National Standards InstituteApproved October 9, 1975Canadian Standards AssociationApproved Adopted for Mandatory Use October 31, 1975Department of Defense, United States of AmericaiiIEEE Std 315-1975(ANSI Y32.2-1975)31 October, 1975Acc

4、eptance NoticeThe following Industry Standardization Document was adopted on 31 October 1975 for mandatory use by the DoD.The indicated industry groups have furnished the clearances required by existing regulations. Copies of the documentsare stocked by DoD Single Stock Point, Naval Publications and

5、 Forms Center, Philadelphia, PA, 19120, for issue tomilitary activities only.Title of Document: Graphic Symbols for Electrical and Electronics Diagrams (Including Reference Designation ClassDesignation Letters)Document No. (a) IEEE Std 315-1975(b) ANSI Y32.2-1975Date of Specific Issue Adopted: (a) 4

6、 September, 1975(b) 31 October, 1975Releasing Industry Group: (a) The Institute of Electrical and Electronics Engineers, Inc.(b) American National Standards Institute, Inc.Supersedes: IEEE Std 315-1971(ANSI Y32.2-1970)Custodians: Military Coordinating Activity:Army - EL Army - ELNavy - SHAir Force -

7、 16Review Activities:Army - AV, MI, MUNavy AS, OS, SH, YDUser Activities: Project Number: DRPR-0176Army - MENavy - EC, MCCertain provisions of this standard are subject of International Standardization Agreement, ABC NAVY STD-28A,Symbols and Abbreviations for Electrical and Electronics Drawings, to

8、which the U.S. Army also subscribes. Whenreaffirmations, amendment, revision, or cancellation of this standard is proposed which will effect or violate theinternational agreement concerned, the Military Coordinating Activity will take appropriate reconcilliation actionthrough military international

9、standardization channels including departmental standardization offices, if required.NOTICE: When reaffirmation, amendment, revision, or cancellation of this standard is initially proposed, thecognizant secretariat of the industry standard shall inform the Military Coordinating Activity of the propo

10、sed changeand request their participation. iiiPreface to CSA Standard Z99-1975 C11BGraphic Symbols for Electrical and Electronics DiagramsREXDALE, October 9, 1975American National Standard Y32.2-1975 (IEEE Std 315-1975), with the modifications shown in Section 100, has beenapproved as CSA Standard Z

11、99. This action was proposed by the Committee on Electrical Symbols, under thejurisdiction of the Sectional Committee on Abbreviations, Definitions and Symbols and was formerly approved bythese Committees. See Section 100, Canadian Standard Z99 modifications to American National Standard Y32.2-1975

12、on page 83. NOTE: In order to keep abreast of progress in the industries concerned, CSA publications are subject to periodicreview. Suggestions for improvement will be welcomed at all times. They will be recorded and in due course broughtto the attention of the appropriate Committee for consideratio

13、n.Also, requests for interpretation will be accepted by the Committee. They should be worded in such a manner as topermit a simple “yes” or “no” answer based on the literal text of the requirement concerned. All inquiries regarding this standard should be addressed to Canadian Standards Association,

14、 178 Rexdale Boulevard,Rexdale, Ontario M9W 1R3, Canada.IEEE Standards BoardApproved September 4, 1975Joseph L. Koepfinger, Chair Warren H. Cook, Vice Chair Sava I. Sherr, Secretary Jean Jacques ArchambaultRobert D. BriskmanDale R. CochranLouis CostrellFrank DavidoffJay ForsterIrvin N. Howell, JrStu

15、art P. JacksonIrving KolodnyWilliam R. KruesiBenjamin J. LeonAnthony C. LordiDonald T. MichaelVoss A. MooreWilliam S. MorganWilliam J. NeiswenderGustave ShapiroRalph M. ShowersRobert A. SodermanLeonard ThomasCharles L. WagnerWilliam T. WintringhamCopyright 1975 by the Institute of Electrical and Ele

16、ctronics Engineers, Inc. No part of this publication may bereproduced in any form, in an electronic retrieval system or otherwise, without the prior written permission of thepublisher. However, individual symbols contained in this standard may be utilized without further permission of theIEEE. Any s

17、tatement that the symbols used are in conformance with this standard shall be on the users ownresponsibility.ivForeword(This foreword is not a part of American National Standard Graphic Symbols for Electrical and Electronics Diagrams, Y32.2-1975IEEE Std 315-1975)This American National Standard is a

18、revision and expansion of American National Standard Graphic Symbols forElectrical and Electronics Diagrams, Y32.2-1970 (IEEE Std 315-1971). A variety of specialized symbols originally used for aircraft applications have been added to make this standard morecomprehensive. To improve coordination wit

19、h IEC publication 117, IEC approved versions of capacitor, transformer,delay, associated conductors and specialized ground symbols have been added as alternates to those long used andstandardized in the United States. A number of small changes have made the existing material more closely parallel to

20、IEC Publication 117. Symbols have been added to cover additional devices in the photo sensitive semiconductor andspecialized semiconductor fields, as well as for an electronic flash lamp. Known errors have been corrected and someitems have been clarified.The reference designation class letters were

21、revised to include the added new device symbols and to clarify the DS andLS categories. “D” is now listed as an alternate to the common “CR” for the common semiconductor diode family ofdevices.All of the symbols are designed so that their connection points fall on a modular grid. This should help th

22、ose who usea grid basis for the preparation of diagrams. By proper enlargement of the symbols the usual coordinate-grid sizes canbe matched. Most symbols appearing in this standard were reproduced form original drawings prepared for theMergenthaler Diagrammer.A substantial effort has been made to ha

23、ve this American National Standard compatible with approved InternationalElectronical Commission (IEC) Recommendations (IEC Publication 117, in various parts). Electrical diagrams are afactor in international trade; the use of one common symbol language ensures a clear presentation and economicaldia

24、gram preparation for a variety of users. Members of the preparing committee have been active in transmitting USAviewpoints to the cognizant IEC Technical Committee.Alternative symbols are shown only in those cases where agreement on a common symbol could not be attained at thistime. It is hoped that

25、 the number of alternative symbols will be reduced in future editions.The symbols in this standard represent the best consensus that can be attained at this time. Standardization, however,must be dynamic, not static, and any solution of a problem should be tested through use and revised if necessary

26、. It isanticipated that the contents of this standard will be modified as future needs dictate; such modifications will be madeavailable through the issuance of approved supplements. Suggestions for improvement are welcomed. They should beaddressed to:Secretary, IEEE Standards BoardInstitute of Elec

27、trical and Electronics Engineers, Inc.345 East 47 StreetNew York, N.Y. 10017This standard has been prepared by the Institute of Electrical and Electronics Engineers (IEEE) StandardsCoordinating Committee for Letter and Graphic Symbols (SCC 11), acting for the Y32.2 Task Group on GraphicSymbols for E

28、lectrical and Electronics Diagrams of the American National Standards Committee Y32, GraphicSymbols and Designations. There has been close cooperation between the industry and DOD representatives toprovide one standard that can be universally used, rather than separate documents with their tendency

29、to differ invarious respects. While credit for this accomplishment is due all participants and the organizations they represent,particular mention is given to the U.S. Department of Defense, without whose strong support in reaching theobjectivestandard symbols acceptable to both industry and the mil

30、itary departmentsthe effort would not havesucceeded.This standard is complemented by a number of related standards listed in Section 23.vThe American National Standards Committee on Graphic Symbols and Designations, Y32, had the followingpersonnel at the time it approved this standard:Charles A. Fri

31、cke, Chair Conrad R. Muller, Vice Chair, Electrical and ElectronicsJames L. Fisher, Jr., Vice Chair, Pictographic SymbolsJames R. Couper, Vice Chair, Chemical and ProcessGeorge Platt, Vice Chair, MechanicalAlvin Lai, Secretary Organization Represented Name of RepresentativeAcoustical Society of Amer

32、ica . Laurence BatchelderHarry F. OlsonAmerican Chemical SocietyRobert F. SchuererAmerican Gear Manufactures Association Gerald L. ScottAmerican Institute of Chemical Engineers . James R. CouperAmerican Institute for Design and Drafting Francis SaintAmerican Institute of Industrial Engineers Irving

33、GoldsteinAmerican Institute of Mining, Metallurgical and Petroleum Engineers (Vacant)American Society of Agriculture Engineers James A. BasselmanAmerican Society of Civil Engineers. (Vacant)American Society for Engineering Education I. L. HillR. T. NorthupAmerican Society of Heating, Refrigerating a

34、nd Air Conditioning Engineers N. LaCourteC.W. MacPhee (Alt)American Society of Mechanical Engineers.R. W. CockrellA. R. Machell, Jr.O. J. MahaH. E. WalchliAmerican Society of Sanitary Engineering. James C. ChurchAmerican Welding Society .A. P. ArndtFrank Speight (Alt)Association of American Railroad

35、s M. F. McCorcleP. H. FoleyAssociation for Computing Machinery. Patrick G. SkellyArthur C. Gannet (Alt)Canadian Standards AssociationA. HendryIlluminating Engineering Society L. E. BarbrowJohn E. Kaufman (Alt)Individual Member. Charles A. FrickeInstitute of Electrical and Electronics Engineers . G.

36、A. KnappSidney V. SoanesSteven A. WassermannInstrument Society of America .George PlattLouis Costea (Alt)Mechanical Contractors Association of America J. R. ManceNational Association of Plumbing, Heating, Cooling ContractorsR. E. WhiteNational Electrical Contractors Association. William H. PaulesNat

37、ional Electrical Manufacturers Association Walter F. HuetteF. V. KupchakR. F. Franciose (Alt)Roland Russo (Alt)Mrs. R. L. Mancini (Alt)National Fluid Power Association .James L. Fisher, Jr.viSociety of Automotive Engineers .H. L. DubocqTechnical Drawing Associates .W. D. ZbinderTelephone GroupH. A.

38、SpielmanR. E. Thiemer (Alt)US Department of the Army, Ordnance.C. A. NazianUS Department of Commerce, National Bureau of Standards Gustave ShapiroUS Department of Commerce, Patent Office.D. M. MillsUS Department of the Interior Ray FreemanUS Department of the Navy. (Vacant)Western Union Telegraph Co

39、mpany (Vacant)The Task Group on Graphic Symbols, Y32.2, which revised and processed this standard, had the following personnel:C. A. Fricke*, Chair S. A. Wassermann, Secretary S. J. BalkeL. BatchelderL. E. BarbrowV. W. BennettH. L. CookD. DrusdowS. K. GhandiW. GrassonC. J. HartA. Hendry, Canadian Li

40、aisonG. A. KnappR. Legg*L. A. MeadowsC. R. Muller*C. A. NazianR. V. RiceE. F. V. Robinson, Canadian LiaisonJ. W. SiefertR. M. Stern*J. ZenoThe IEEE Standards Coordinating Committee on Letter and Graphic Symbols, SCC 11, had the followingmembership:C. A. Fricke, Chair C. R. Muller, Secretary R. B. Au

41、gus, JrF. K. BeckerJ. C. BrownJ. M. CarrollH. L. CookE. T. B. GrossG. A. KnappL. A. MeadowsR. V. RiceG. ShapiroJ. W. SiefertS. V. SoanesR. M. SternL. H . WarrenS. A. WassermannJ. C. WhiteThe IEEE Subcommittee on Graphic Symbols, SCC 11.1, and the IEC Experts Subcommittee, SCC 11.6, had thefollowing

42、membership:C. A. Fricke, Chair SCC 11.1C. A. Fricke, Chair pro tem, SCC 11.6V. W. BennettI. M. Berger (SCC 11.1)T. L. BisbeeV. CondelloH. L. CookD. DrusdowA. C. GannettG. A. KnappE. J. Lombardi (SCC 11.6)R. LeggJ. Lusti (SCC 11.6)L. A. MeadowsC. R. MullerG. Panula (SCC 11.6)R. V. Rice (SCC 11.1)A. I

43、. Rubin (SCC 11.1)F. A. SaintG. ShapiroJ. W. Siefert (SCC 11.1)H. SeamanP. G. Skelly (SCC 11.6)S. V. Soanes (SCC 11.1)R. M. SternS. A. WassermanR. Rondinelli (Alt)W. W. Varnedoe (SCC 11.6)J. Zeno (SCC 11.1)* Member of Y32.2 Editorial Committee. Retired.viiCLAUSE PAGEIntroduction.1A1 Scope 1A2 Arrang

44、ement. 2A3 Application. 2A4 Drafting Practices Applicable to Graphic Symbols . 3Section 1 Qualifying Symbols 51.1 Adjustability Variability 51.2 Special-Property Indicators 71.3 Radiation Indicators (electromagnetic and particulate) . 81.4 Physical State Recognition Symbols 91.5 Test-Point Recogniti

45、on Symbol. 101.6 Polarity Markings. 101.7 Direction of Flow of Power, Signal, or Information 121.8 Kind of Current (General) 131.9 Connection Symbol 141.10 Envelope Enclosure 171.11 Shield Shielding 181.12 Special Connector or Cable Indicator 191.13 Electret (shown with electrodes) 19Section 2 Graph

46、ic Symbols for Fundamental Items (not included in other sections).192.1 Resistor. 192.2 Capacitor 242.3 Antenna . 282.4 Attenuator. 322.5 Battery 332.6 Delay Function Delay Line Slow-Wave Structure . 342.7 Oscillator Generalized Alternating-Current Source . 352.8 Permanent Magnet 352.9 Pickup Head .

47、 352.10 Piezoelectric Crystal Unit (including Crystal Unit, Quartz ) 362.11 Transducer Accelerometer Motional Pickup Transducer 362.12 Squib, Electric . 372.13 Thermocouple (dissimilar-metals device) 372.14 Thermal Element Thermomechanical Transducer 382.15 Spark Gap Igniter Gap . 38viiiCLAUSE PAGE2

48、.16 Continuous Loop Fire Detector (temperature sensor) 382.17 Ignitor Plug 38Section 3 Graphic Symbols for Transmission Path 393.1 Transmission Path Conductor Cable Wiring. 393.2 Distribution Lines Transmission Lines 453.3 Alternative or Conditional Wiring . 473.4 Associated or Future 473.5 Intentio

49、nal Isolation of Direct-Current Path in Coaxial or Waveguide Applications 483.6 Waveguide 483.7 Strip-Type Transmission Line . 493.8 Termination 493.9 Circuit Return. 503.10 Pressure Tight Bulkhead Cable Gland Cable Sealing End. 51Section 4 Graphic Symbols for Contacts, Switches, Contactors, and Relays.524.1 Switching Function 524.2 Electrical Contact 524.3 Basic Contact Assemblies 544.4 Magnetic Blowout Coil 574.5 Operating Coil Relay Coil 574.6 Switch. 584.7 Pushbutton, Momentary or Spring-Return. 594.8 Two-circuit, Maintained or Not Spring-Return . 604.9 Nonlocking Sw