IEEE 2401-2015 en Format for LSI-Package-Board Interoperable Design (IEEE Computer Society).pdf

《IEEE 2401-2015 en Format for LSI-Package-Board Interoperable Design (IEEE Computer Society).pdf》由会员分享，可在线阅读，更多相关《IEEE 2401-2015 en Format for LSI-Package-Board Interoperable Design (IEEE Computer Society).pdf（206页珍藏版）》请在麦多课文档分享上搜索。

1、 IEEE Standard Format for LSI-Package-Board Interoperable Design Sponsored by the Design Automation Standards Committee IEEE 3 Park Avenue New York, NY 10016-5997 USA IEEE Computer Society IEEE Std 2401-2015 IEEE Std 2401-2015 IEEE Standard Format for LSI-Package-Board Interoperable Design Sponsor D

2、esign Automation Standards Committee of the IEEE Computer Society Approved 3 September 2015 IEEE-SA Standards Board Copyrights and Permissions The following figures are reprinted with permission from JEITA1 Figure i, Figure ii, Figure 1, Figure 3, Figure 16, Figure 17, Figure 18, Figure 19, Figure 2

3、0, Figure 21, Figure 22, Figure 23, Figure 24, Figure 25, Figure 26, Figure 27, Figure 28, Figure 29, Figure 30, Figure 31, Figure 32, Figure 33, Figure 34, Figure 35, Figure 36, Figure 37, Figure 38, Figure 39, Figure 40, Figure 41, Figure 42, Figure 43, Figure 44, Figure 45, Figure 46, Figure 47,

4、Figure 48, Figure 49, Figure 50, Figure 51, Figure 60, Figure 61, Figure 62, Figure 63, Figure B.1, Figure B.3, Figure B.5, Figure B.6, Figure B.7, Figure B.8, Figure B.10, Figure B.11, Figure B.12, Figure B.13, Figure B.14, Figure B.15, Figure B.16, Figure B.17, Figure B.18, Figure B.19, Figure B.2

5、0, Figure B.21, Figure B.22, Figure B.23, Figure B.24, Figure B.25, Figure B.26, Figure B.27, Figure B.28, Figure B.29 Abstract: A method is provided for specifying a common interoperable format for electronic systems design. The format provides a common way to specify information/data about the pro

6、ject management, netlists, components, design rules, and geometries used in Large-Scale Integrated Circuit-Package-Board designs. The method provides the ability to make electronic systems a key consideration early in the design process; design tools can use it to exchange information/data seamlessl

7、y. Keywords: common interoperable format, components, design analysis, design rules, geometries, IEEE 2401, large-scale integrated circuits, netlists, packages for LSI circuits, printed circuit board, project management, Verilog-HDL 1Every effort has been made to secure permission to reprint borrowe

8、d material contained in this document. If omissions have been made, please bring them to our attention. The Institute of Electrical and Electronics Engineers, Inc. 3 Park Avenue, New York, NY 10016-5997, USA Copyright 2015 by The Institute of Electrical and Electronics Engineers, Inc. All rights res

9、erved. Published 18 December 2015. Printed in the United States of America. IEEE is a registered trademark in the U.S. Patent fitness for a particular purpose; non-infringement; and quality, accuracy, effectiveness, currency, or completeness of material. In addition, IEEE disclaims any and all condi

10、tions relating to: results; and workmanlike effort. IEEE standards documents are supplied “AS IS” and “WITH ALL FAULTS.” Use of an IEEE standard is wholly voluntary. The existence of an IEEE standard does not imply that there are no other ways to produce, test, measure, purchase, market, or provide

11、other goods and services related to the scope of the IEEE standard. Furthermore, the viewpoint expressed at the time a standard is approved and issued is subject to change brought about through developments in the state of the art and comments received from users of the standard. In publishing and m

12、aking its standards available, IEEE is not suggesting or rendering professional or other services for, or on behalf of, any person or entity nor is IEEE undertaking to perform any duty owed by any other person or entity to another. Any person utilizing any IEEE Standards document, should rely upon h

13、is or her own independent judgment in the exercise of reasonable care in any given circumstances or, as appropriate, seek the advice of a competent professional in determining the appropriateness of a given IEEE standard. IN NO EVENT SHALL IEEE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL

14、, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO: PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE

15、) ARISING IN ANY WAY OUT OF THE PUBLICATION, USE OF, OR RELIANCE UPON ANY STANDARD, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE AND REGARDLESS OF WHETHER SUCH DAMAGE WAS FORESEEABLE. Translations The IEEE consensus development process involves the review of documents in English only. In the ev

16、ent that an IEEE standard is translated, only the English version published by IEEE should be considered the approved IEEE standard. Official statements A statement, written or oral, that is not processed in accordance with the IEEE-SA Standards Board Operations Manual shall not be considered or inf

17、erred to be the official position of IEEE or any of its committees and shall not be considered to be, or be relied upon as, a formal position of IEEE. At lectures, symposia, seminars, or educational courses, an individual presenting information on IEEE standards shall make it clear that his or her v

18、iews should be considered the personal views of that individual rather than the formal position of IEEE. Comments on standards Comments for revision of IEEE Standards documents are welcome from any interested party, regardless of membership affiliation with IEEE. However, IEEE does not provide consu

19、lting information or advice pertaining to IEEE Standards documents. Suggestions for changes in documents should be in the form of a proposed change of text, together with appropriate supporting comments. Since IEEE standards represent a consensus of concerned interests, it is important that any resp

20、onses to comments and questions also receive the concurrence of a balance of interests. For this reason, IEEE and the members of its societies and Standards Coordinating Committees are not able to provide an instant response to comments or questions except in those cases where the matter has previou

21、sly been addressed. For the same reason, IEEE does not respond to interpretation requests. Any person who would like to participate in revisions to an IEEE standard is welcome to join the relevant IEEE working group. Comments on standards should be submitted to the following address: Secretary, IEEE

22、-SA Standards Board 445 Hoes Lane Piscataway, NJ 08854 USA Laws and regulations Users of IEEE Standards documents should consult all applicable laws and regulations. Compliance with the provisions of any IEEE Standards document does not imply compliance to any applicable regulatory requirements. Imp

23、lementers of the standard are responsible for observing or referring to the applicable regulatory requirements. IEEE does not, by the publication of its standards, intend to urge action that is not in compliance with applicable laws, and these documents may not be construed as doing so. Copyrights I

24、EEE draft and approved standards are copyrighted by IEEE under U.S. and international copyright laws. They are made available by IEEE and are adopted for a wide variety of both public and private uses. These include both use, by reference, in laws and regulations, and use in private self-regulation,

25、 standardization, and the promotion of engineering practices and methods. By making these documents available for use and adoption by public authorities and private users, IEEE does not waive any rights in copyright to the documents. Photocopies Subject to payment of the appropriate fee, IEEE will g

26、rant users a limited, non-exclusive license to photocopy portions of any individual standard for company or organizational internal use or individual, non-commercial use only. To arrange for payment of licensing fees, please contact Copyright Clearance Center, Customer Service, 222 Rosewood Drive, D

27、anvers, MA 01923 USA; +1 978 750 8400. Permission to photocopy portions of any individual standard for educational classroom use can also be obtained through the Copyright Clearance Center. Updating of IEEE Standards documents Users of IEEE Standards documents should be aware that these documents ma

28、y be superseded at any time by the issuance of new editions or may be amended from time to time through the issuance of amendments, corrigenda, or errata. An official IEEE document at any point in time consists of the current edition of the document together with any amendments, corrigenda, or errat

29、a then in effect. Every IEEE standard is subjected to review at least every ten years. When a document is more than ten years old and has not undergone a revision process, it is reasonable to conclude that its contents, although still of some value, do not wholly reflect the present state of the art

30、. Users are cautioned to check to determine that they have the latest edition of any IEEE standard. In order to determine whether a given document is the current edition and whether it has been amended through the issuance of amendments, corrigenda, or errata, visit the IEEE-SA Website at http:/ieee

31、xplore.ieee.org/xpl/standards.jsp or contact IEEE at the address listed previously. For more information about the IEEE SA or IEEEs standards development process, visit the IEEE-SA Website at http:/standards.ieee.org. Errata Errata, if any, for all IEEE standards can be accessed on the IEEE-SA Websi

32、te at the following URL: http:/standards.ieee.org/findstds/errata/index.html. Users are encouraged to check this URL for errata periodically. Patents Attention is called to the possibility that implementation of this standard may require use of subject matter covered by patent rights. By publication

33、 of this standard, no position is taken by the IEEE with respect to the existence or validity of any patent rights in connection therewith. If a patent holder or patent applicant has filed a statement of assurance via an Accepted Letter of Assurance, then the statement is listed on the IEEE-SA Websi

34、te at http:/standards.ieee.org/about/sasb/patcom/patents.html. Letters of Assurance may indicate whether the Submitter is willing or unwilling to grant licenses under patent rights without compensation or under reasonable rates, with reasonable terms and conditions that are demonstrably free of any

35、unfair discrimination to applicants desiring to obtain such licenses. Essential Patent Claims may exist for which a Letter of Assurance has not been received. The IEEE is not responsible for identifying Essential Patent Claims for which a license may be required, for conducting inquiries into the le

36、gal validity or scope of Patents Claims, or determining whether any licensing terms or conditions provided in connection with submission of a Letter of Assurance, if any, or in any licensing agreements are reasonable or non-discriminatory. Users of this standard are expressly advised that determinat

37、ion of the validity of any patent rights, and the risk of infringement of such rights, is entirely their own responsibility. Further information may be obtained from the IEEE Standards Association. Participants At the time this IEEE standard was completed, the P2401 Working Group had the following m

38、embership: Yoshinori Fukuba, Chair Yukio Masuko, Vice Chair Takahiro Aoki Bradley Brim Norman Chang John Ellis Tadaaki Hitomi Hiroshi Ishikawa Takashi Otsuki John Park Herb Reiter Genichi Tanaka Atsushi Tomishima The following members of the entity balloting committee voted on this standard. Ballote

39、rs may have voted for approval, disapproval, or abstention. Cadence Design Systems, Inc. Japan Electronics and Information Technology Industries Association (JEITA) Marvell Semiconductor, Inc. Synopsys, Inc. Toshiba Corporation When the IEEE-SA Standards Board approved this standard on 3 September 2

40、015, it had the following membership: John D. Kulick, Chair Jon Walter Rosdahl, Vice Chair Richard H. Hulett, Past Chair Konstantinos Karachalios, Secretary Masayuki Ariyoshi Ted Burse Stephen Dukes Jean-Philippe Faure J. Travis Griffith Gary Hoffman Michael Janezic Joseph L. Keopfinger David J. Law

41、 Hung Ling Andrew Myles T. W. Olsen Glenn Parsons Ronald C. Petersen Annette D. Reilly Stephen J. Shellhammer Adrian P. Stephens Yatin Trivedi Philip Winston Don Wright Yu Yuan Daidi Zhong *Member Emeritus Copyright 2015 IEEE. All rights reserved. vi Introduction This introduction is not part of IEE

42、E Std 2401-2015, IEEE Standard Format for LSI-Package-Board Interoperable Design. To deal with the increasing difficulty of design and the cost competitiveness of the global market, and to shorten the development term, innovative design methodologies should be implemented. It has been difficult to a

43、chieve the optimization of an entire set of large-scale integrated (LSI) circuits, packages, and board (LPB) using individual design processes for each LPB part. One possibility for optimization is to have a certain section design the whole LPB; however, gathering knowledge and integrating the desig

44、n environment of each LPB part is difficult. Dedicated professional technicians of individual LPB parts, who have the best knowledge and performance of their own parts design tools, intend to create design optimization by having proper interoperable information exchanges among all LPB parties. In or

45、der to achieve a design that optimizes the balance between cost and performance, information about and the results of design should be well shared among cooperating LPB design sections. The Japan Electronics and Information Technology Industries Association (JEITA) LPB Interoperable Design Process W

46、orking Group (LPB-WG) was established to identify the solution. The LPB-WG intends to make a standard for an exchange format to make it easy to exchange information between each of the LPB design departments, so that optimal design will be carried out quickly. The LPB interoperable design process ha

47、s the following issues: Netlist not unified on each LPB Complexity of the representation of the relationship as a whole arrangement of the LPB Differences in how to give the design constraints, lack of design information, and many discrepancies in design rules. Databases not unified in each LPB, or

48、among different vendors No unified terms Various problems caused by these issues include the following: A large effort is required for conversion of formats. The occurrence of conversion errors and connection errors is difficult to detect because there is a lack of the information needed to do so. I

49、t takes a long time to gather information, resulting in a long period of design and analysis. It is difficult to make optimal design changes because the entire verification process is difficult. EDA tool cost increase because of additional development required to support multiple formats. It is time-consuming for designers to communicate their intentions in a way that others understand. Based on this analysis, the LPB-WG has established an interface format that can address these issues. As the one of the case studies of the LPB interoperable design process,