IEEE 1904 1-2013 en Service Interoperability in Ethernet Passive Optical Networks (SIEPON)《以太网无源光网络中服务互操作性(SIEPON)用IEEE标准》.pdf

《IEEE 1904 1-2013 en Service Interoperability in Ethernet Passive Optical Networks (SIEPON)《以太网无源光网络中服务互操作性(SIEPON)用IEEE标准》.pdf》由会员分享，可在线阅读，更多相关《IEEE 1904 1-2013 en Service Interoperability in Ethernet Passive Optical Networks (SIEPON)《以太网无源光网络中服务互操作性(SIEPON)用IEEE标准》.pdf（834页珍藏版）》请在麦多课文档分享上搜索。

1、 IEEE Standard for Service Interoperability in Ethernet Passive Optical Networks (SIEPON) Sponsored by the Standards Development Board IEEE 3 Park Avenue New York, NY 10016-5997 USA 14 June 2013 IEEE Communications Society IEEE Std 1904.1-2013IEEE Std 1904.1-2013 IEEE Standard for Service Interopera

2、bility in Ethernet Passive Optical Networks (SIEPON) Sponsor Standards Development Board of the IEEE Communications Society Approved 14 June 2013 IEEE-SA Standards Board Abstract: This standard describes the system-level requirements needed to ensure service-level, multi-vendor interoperability of E

3、thernet Passive Optical Network (EPON) equipment. The specifications complement the existing IEEE 802.3 and IEEE 802.1 standards, which ensure the interoperability at the Physical Layer (PHY) and Data Link Layer. Specifically included in this specification are EPON system-level interoperability spec

4、ifications covering equipment functionality, traffic engineering, and service-level quality of service/class of service (QoS/CoS) mechanisms; Management specifications covering equipment management, service management, and EPON powersaving mechanism. Keywords: 1G-EPON, 10G-EPON, EPON, Ethernet Passi

5、ve Optical Network, IEEE 1904.1, interoperability, QoS, quality of service, service interoperability, SIEPONGrateful acknowledgment is made to The Broadband Forum for the permission to use the following source material: BBF TR-200, Using EPON in the Context of TR-101, L. D. Lamb and C. Shen, Eds., C

6、opyright 2011, The Broadband Forum, Section 1.2, Figure 1, page 10. The Institute of Electrical and Electronics Engineers, Inc. 3 Park Avenue, New York, NY 10016-5997, USA Copyright 2013 by The Institute of Electrical and Electronics Engineers, Inc. All rights reserved. Published 20 September 2013.

7、Printed in the United States of America. DPoE and DOCSIS standards or products referred to in this standard are trademarks of the Cable Television Laboratories, Inc. IEEE and IEEE 802 are registered trademarks in the U.S. Patent +1 978 750 8400. Permission to photocopy portions of any individual sta

8、ndard for educational classroom use can also be obtained through the Copyright Clearance Center. iv Copyright 2013 IEEE. All rights reserved. Notice to users Laws and regulations Users of IEEE Standards documents should consult all applicable laws and regulations. Compliance with the provisions of a

9、ny IEEE Standards document does not imply compliance to any applicable regulatory requirements. Implementers of the standard are responsible for observing or referring to the applicable regulatory requirements. IEEE does not, by the publication of its standards, intend to urge action that is not in

10、compliance with applicable laws, and these documents may not be construed as doing so. Copyrights This document is copyrighted by the IEEE. It is made available for a wide variety of both public and private uses. These include both use, by reference, in laws and regulations, and use in private self-

11、regulation, standardization, and the promotion of engineering practices and methods. By making this document available for use and adoption by public authorities and private users, the IEEE does not waive any rights in copyright to this document. Updating of IEEE documents Users of IEEE Standards do

12、cuments should be aware that these documents may be superseded at any time by the issuance of new editions or may be amended from time to time through the issuance of amendments, corrigenda, or errata. An official IEEE document at any point in time consists of the current edition of the document tog

13、ether with any amendments, corrigenda, or errata then in effect. In order to determine whether a given document is the current edition and whether it has been amended through the issuance of amendments, corrigenda, or errata, visit the IEEE-SA Website at http:/standards.ieee.org/index.html or contac

14、t the IEEE at the address listed previously. For more information about the IEEE Standards Association or the IEEE standards development process, visit the IEEE-SA Website at http:/standards.ieee.org/index.html. Errata Errata, if any, for this and all other standards can be accessed at the following

15、 URL: http:/standards.ieee.org/findstds/errata/index.html. Users are encouraged to check this URL for errata periodically. Patents Attention is called to the possibility that implementation of this standard may require use of subject matter covered by patent rights. By publication of this standard,

16、no position is taken by the IEEE with respect to the existence or validity of any patent rights in connection therewith. If a patent holder or patent applicant has filed a statement of assurance via an Accepted Letter of Assurance, then the statement is listed on the IEEE-SA Website http:/standards.

17、ieee.org/about/sasb/patcom/patents.html. Letters of Assurance may indicate whether the Submitter is willing or unwilling to grant licenses under patent rights without compensation or under reasonable rates, with reasonable terms and conditions that are demonstrably free of any unfair discrimination

18、to applicants desiring to obtain such licenses. Essential Patent Claims may exist for which a Letter of Assurance has not been received. The IEEE is not responsible for identifying Essential Patent Claims for which a license may be required, for conducting inquiries into the legal validity or scope

19、of Patents Claims, or determining whether any licensing terms or conditions provided in connection with submission of a Letter of Assurance, if any, or in any licensing agreements are reasonable or nondiscriminatory. Users of this standard are expressly advised that v Copyright 2013 IEEE. All rights

20、 reserved. determination of the validity of any patent rights, and the risk of infringement of such rights, is entirely their own responsibility. Further information may be obtained from the IEEE Standards Association. Participants At the time this standard was submitted to the IEEE-SA Standards Boa

21、rd for approval, the SIEPON Working Group had the following membership: Glen Kramer, Working Group Chair Ken-Ichi Suzuki, Working Group Vice Chair Zhou Zhen, Executive Secretary Marek Hajduczenia, Chief Editor Lior Khermosh, Service Configuration and Provisioning Task Force Chair Alan M. Brown, Serv

22、ice Configuration and Provisioning Task Force Editor Curtis Knittle, Performance Requirements and Service Quality Task Force Chair Jeff Stribling, Performance Requirements and Service Quality Task Force Editor Seiji Kozaki, Service Survivability Task Force Chair Jeff Stribling, Service Survivability

23、 Task Force Editor James Chen, System/Device Management Task Force Chair Fumio Daido, System/Device Management Task Force Editor Toshihiko Kusano, Conformance Test Procedures Task Force Chair Marek Hajduczenia, Conformance Test Procedures Task Force Editor for Package A Motoyuki Takizawa, Conformanc

24、e Test Procedures Task Force Editor for Package B Liu Qian, Conformance Test Procedures Task Force Editor for Package C The following individuals submitted technical contributions or commented on the standard at various stages of the project development. Venkat Arunarthi, Cortina Victor Blake, Victo

25、r Blake Wang Bo, China Telecommunications Corp. Zhang Boshan, ZTE Corporation Alan M. Brown, Aurora Networks Xiao Chen, Alcatel-Lucent Shen Chengbin, China Telecom Fumio Daido, Sumitomo Electric Industries Ltd. Peng Du, Broadcom Corporation Hesham ElBakoury, Huawei Technologies Michael Emmendorfer,

26、ARRIS Josh Feinstein, Broadcom Corporation Marek Hajduczenia, ZTE Corporation Ryan Hirth, Broadcom Corporation Takeshi Imai, Mitsubishi Electric Corporation Ryo Inohara, KDDI R&D Laboratories Inc. Erez Izenberg, Marvell Qiang Jiang, Broadcom Corporation Keisuke Jinen, Sumitomo Electric Industries Lt

27、d. Manabu Kato, PMC-Sierra, Inc. Lior Khermosh, PMC-Sierra, Inc. Mitsunobu Kimura, Hitachi, Ltd. Curtis Knittle, Cable Television Laboratories (CableLabs) Shinichi Kouyama, Sumitomo Electric Industries Ltd. Seiji Kozaki, Mitsubishi Electric Corporation Glen Kramer, Broadcom Corporation Toshihiko Kus

28、ano, Oliver Solutions, Ltd. Lowell Lamb, Broadcom Corporation Jeff Lapak, University of New Hampshire-IOL Rick Li, Cortina Xuguang Li, Qualcomm Wei Lin, Huawei Technologies Eric Lynskey, Broadcom Corporation Bob Mandeville, Iometrix Jeff Mandin, PMC-Sierra, Inc. Makoto Matsuoka, Hitachi, Ltd. Hiroak

29、i Mukai, Mitsubishi Electric Corporation Daisuke Murayama, NTT Corporation Kenichi Nakura, Mitsubishi Electric Corporation Susumu Nishihara, NTT Corporation Kazumi Onishi, Oki Electric Industry Co., Ltd. Liu Qian, RITT, CATR Duane Remein, FiberHome Technologies Shoichiro Seno, Mitsubishi Electric Co

30、rporation Kenichi Shimamura, NEC Santanu Sinha, Cortina Oren Spector, Oliver Solutions, Ltd. vi Copyright 2013 IEEE. All rights reserved. Jeff Stribling, Hitachi Communications Technologies America, Inc. Takeshi Suehiro, Mitsubishi Electric Corporation Ken-Ichi Suzuki, NTT Corporation Masashi Tadoko

31、ro, NTT Corporation Makoto Taguchi, PMC-Sierra, Inc. Akihiro Takahashi, Oki Electric Industry Co., Ltd. Motoyuki Takizawa, Fujitsu Telecom Networks, Ltd. Kiyoshi Uematsu, Oki Electric Industry Co., Ltd. Chengwei Wang, China Telecommunications Corp. Lu Yang, RITT, CATR Hosung Yoon, KT He Yuanling, ZT

32、E Corporation Meiyan Zang, ZTE Corporation Zhou Zhen, FiberHome Technologies The following members of the entity balloting committee voted on this standard. Balloters may have voted for approval, disapproval, or abstention. Aurora Networks, Inc. Broadcom Corporation Cable Television Laboratories Inc

33、. (CableLabs) Cortina Systems FiberHome Technologies Group FUJITSU Hitachi, Ltd. KT Corp. Maxim Integrated Products Mitsubishi Electric Corporation Mstar Semiconductor, Inc. NEC Corporation Nippon Telegraph and Telephone Corporation (NTT) Nokia Oki Electric Industry Co., Ltd. Oliver Solutions PMC-Si

34、erra, Inc. Qualcomm Incorporated Research Institute of Telecommunications Transmission of Ministry of Industry and Information Technology (RITT) (MITT) Sumitomo Electric Industries, LTD UNH-IOL Xilinx ZTE Corporation When the IEEE-SA Standards Board approved this standard on 14 June 2013, it had the

35、 following membership: John Kulick, Chair David J. Law, Vice Chair Richard H. Hulett, Past Chair Konstantinos Karachalios, Secretary Masayuki Ariyoshi Peter Balma Farooq Bari Ted Burse Wael William Diab Stephen Dukes Jean-Philippe Faure Alexander Gelman Mark Halpin Gary Hoffman Paul Houz Jim Hughes

36、Michael Janezic Joseph L. Koepfinger* Oleg Logvinov Ron Petersen Gary Robinson Jon Walter Rosdahl Adrian Stephens Peter Sutherland Yatin Trivedi Phil Winston Yu Yuan*Member Emeritus Also included are the following nonvoting IEEE-SA Standards Board liaisons: Richard DeBlasio, DOE Representative Micha

37、el Janezic, NIST Representative Don Messina IEEE Standards Program Manager, Document Development Soo H. Kim IEEE Client Services Manager, Professional Services vii Copyright 2013 IEEE. All rights reserved. Introduction This introduction is not part of IEEE Std 1904.1-2013, IEEE Standard for Service

38、Interoperability in Ethernet Passive Optical Networks (SIEPON). This standard builds upon the IEEE 802.3ah (1G-EPON) and IEEE 802.3av (10G-EPON) Physical Layer and Data Link Layer specifications and provides system-level and network-level definitions of numerous EPON features, geared toward fosterin

39、g interoperability between various implementations aiming to provide the same set of functionalities.aThese Service Interoperability in Ethernet Passive Optical Networks (SIEPON) features allow “plug-and-play” interoperability of the transport, service, and control planes in a multi-vendor environme

40、nt. This standard serves a number of important purposes: Compliant EPON devices follow a common specification for the worldwide market, potentially resulting in larger volumes and reduced costs. Operators may not face the challenge of developing system-level specifications and interoperability testi

41、ng procedures before they can deploy EPON. EPON vendors may not need to implement multiple options to comply with multiple proprietary/national specifications. Reduced device complexity may further reduce cost. Competition among EPON equipment and component suppliers may increase, thus potentially d

42、riving further innovation and cost reductions. _ aInformation on references can be found in Clause 2. viii Copyright 2013 IEEE. All rights reserved. Contents 1 Overview 1 1.1 Scope . 1 1.2 Purpose 1 1.3 Coverage . 2 1.4 Overview of clauses 2 2 Normative references 4 3 Definitions, acronyms, and abbr

43、eviations . 7 3.1 Definitions. 7 3.2 Acronyms and abbreviations 10 3.3 Special terms 15 3.4 Primitives in SIEPON 16 3.5 Notation for state diagrams 16 3.5.1 General conventions. 16 3.5.1.1 Representation of states 17 3.5.1.2 Transitions 17 3.5.2 State diagrams and accompanying text 18 3.5.3 Actions

44、inside state blocks . 18 3.5.4 State diagram variables 18 3.5.5 Operators 18 3.5.6 Timers 19 3.5.7 Hexadecimal notation 19 3.5.8 Binary notation 19 3.6 Notation for PICS 19 3.6.1 Abbreviations and special symbols 20 3.6.2 Instructions for completing the PICS proforma . 20 3.6.3 Additional informatio

45、n. 21 3.6.4 Exception information . 21 3.6.5 Conditional items . 21 4 Specification packages .22 4.1 Introduction 22 4.2 SIEPON packages 22 4.3 Compliance with IEEE Std 802.3 25 4.4 Extended OAM 25 5 Scope and architecture .26 5.1 Introduction 26 5.2 Coverage 26 5.3 EPON system architecture .26 5.3.

46、1 Introduction 26 5.3.2 ODN . 27 5.3.3 ONU architecture . 28 5.3.3.1 L-ONU . 28 5.3.3.2 C-ONU . 30 5.3.3.3 S-ONU . 30 5.3.4 OLT architecture 30 5.3.4.1 L-OLT 31 5.3.4.2 C-OLT 33 5.3.4.3 S-OLT 33 5.3.5 Interfaces 33 5.3.5.1 ONU_MDI . 33 5.3.5.2 OLT_MDI 34 ix Copyright 2013 IEEE. All rights reserved.

47、5.3.5.3 ONU_LI . 34 5.3.5.4 OLT_LI 34 5.3.5.5 ONU_CI . 34 5.3.5.6 OLT_CI 34 5.3.5.7 Internal Interfaces . 35 6 MAC Client reference model .36 6.1 Introduction 36 6.2 MAC Client reference model definition .36 6.2.1 Reference model naming nomenclature . 38 6.2.1.1 Functional blocks . 38 6.2.1.2 Action

48、able entries. 38 6.2.1.3 Functional elements . 39 6.3 EPON Service Path definition 40 6.3.1 ESP examples 40 6.3.2 ESP_CTRL definition 42 6.3.2.1 ESP_VECTOR signal 42 6.3.2.2 ESP_COLOR signal . 43 6.4 Frame flow through reference model .43 6.4.1 Frame flow through EPON OLT . 44 6.4.1.1 Downstream fra

49、mes through OLT . 44 6.4.1.2 Upstream frames through OLT 45 6.4.2 Frame flow through EPON ONU . 46 6.4.2.1 Downstream frames through ONU. 46 6.4.2.2 Upstream frames through ONU . 46 6.5 Blocks in the reference model 47 6.5.1 Input . 47 6.5.2 Classifier 47 6.5.2.1 Classification element (rule) structure . 48 6.5.2.1.1 Classification fields 49 6.5.2.1.1.1 Flexible access mechanism 52 6.5.2.1.2 Comparison operators 52 6.5.2.2 Classifier provisioning model and parameters . 53 6.5.2.2.1 Default configuration . 53 6.5