IEEE 1727 CORR-2015 en Guide for Working Procedures on Underground Transmission Circuits with Induced Voltage Corrigendum 1《带感应电压的地下传输电路工作规程用IEEE指南 勘误1》.pdf

《IEEE 1727 CORR-2015 en Guide for Working Procedures on Underground Transmission Circuits with Induced Voltage Corrigendum 1《带感应电压的地下传输电路工作规程用IEEE指南 勘误1》.pdf》由会员分享，可在线阅读，更多相关《IEEE 1727 CORR-2015 en Guide for Working Procedures on Underground Transmission Circuits with Induced Voltage Corrigendum 1《带感应电压的地下传输电路工作规程用IEEE指南 勘误1》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、 IEEE Guide for Working Procedures on Underground Transmission Circuits with Induced Voltage Corrigendum 1 Sponsored by the Insulated Conductors Committee IEEE 3 Park Avenue New York, NY 10016-5997 USA IEEE Power and Energy Society IEEE Std 1727-2013/Cor 1-2015 (Corrigendum to IEEE Std 1727-2013) IE

2、EE Std 1727-2013/Cor 1-2015 (Corrigendum to IEEE Std 1727-2013) IEEE Guide for Working Procedures on Underground Transmission Circuits with Induced Voltage Corrigendum 1 Sponsor Insulated Conductors Committee of the IEEE Power and Energy Society Approved 16 February 2015 IEEE-SA Standards Board Abst

3、ract: Induced voltage working procedures for underground transmission circuits are established in this guide. A transmission circuit when de-energized will have an induced voltage when in a common duct bank with an energized circuit. The induced voltage may be a possible safety hazard. The induced v

4、oltage may be determined by modeling the circuits and by measurement. This guide addresses the working procedures to follow when performing work where induced voltage is present. Keywords: cable, duct bank, equipment, grounding, IEEE 1727, induced voltage, jointing, underground transmission The Inst

5、itute of Electrical and Electronics Engineers, Inc. 3 Park Avenue, New York, NY 10016-5997, USA Copyright 2015 by The Institute of Electrical and Electronics Engineers, Inc. All rights reserved. Published 20 February 2015. Printed in the United States of America. IEEE is a registered trademark in th

6、e U.S. Patent fitness for a particular purpose; non-infringement; and quality, accuracy, effectiveness, currency, or completeness of material. In addition, IEEE disclaims any and all conditions relating to: results; and workmanlike effort. IEEE standards documents are supplied “AS IS” and “WITH ALL

7、FAULTS.” Use of an IEEE standard is wholly voluntary. The existence of an IEEE standard does not imply that there are no other ways to produce, test, measure, purchase, market, or provide other goods and services related to the scope of the IEEE standard. Furthermore, the viewpoint expressed at the

8、time a standard is approved and issued is subject to change brought about through developments in the state of the art and comments received from users of the standard. In publishing and making its standards available, IEEE is not suggesting or rendering professional or other services for, or on beh

9、alf of, any person or entity nor is IEEE undertaking to perform any duty owed by any other person or entity to another. Any person utilizing any IEEE Standards document, should rely upon his or her own independent judgment in the exercise of reasonable care in any given circumstances or, as appropri

10、ate, seek the advice of a competent professional in determining the appropriateness of a given IEEE standard. IN NO EVENT SHALL IEEE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO: PROCUREMENT OF SUBSTITUTE GOODS OR SERVICE

11、S; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE PUBLICATION, USE OF, OR RELIANCE UPON ANY STANDARD, EVEN IF ADVISED OF THE POSSI

12、BILITY OF SUCH DAMAGE AND REGARDLESS OF WHETHER SUCH DAMAGE WAS FORESEEABLE. Translations The IEEE consensus development process involves the review of documents in English only. In the event that an IEEE standard is translated, only the English version published by IEEE should be considered the app

13、roved IEEE standard. Official statements A statement, written or oral, that is not processed in accordance with the IEEE-SA Standards Board Operations Manual shall not be considered or inferred to be the official position of IEEE or any of its committees and shall not be considered to be, or be reli

14、ed upon as, a formal position of IEEE. At lectures, symposia, seminars, or educational courses, an individual presenting information on IEEE standards shall make it clear that his or her views should be considered the personal views of that individual rather than the formal position of IEEE. Comment

15、s on standards Comments for revision of IEEE Standards documents are welcome from any interested party, regardless of membership affiliation with IEEE. However, IEEE does not provide consulting information or advice pertaining to IEEE Standards documents. Suggestions for changes in documents should

16、be in the form of a proposed change of text, together with appropriate supporting comments. Since IEEE standards represent a consensus of concerned interests, it is important that any responses to comments and questions also receive the concurrence of a balance of interests. For this reason, IEEE an

17、d the members of its societies and Standards Coordinating Committees are not able to provide an instant response to comments or questions except in those cases where the matter has previously been addressed. For the same reason, IEEE does not respond to interpretation requests. Any person who would

18、like to participate in revisions to an IEEE standard is welcome to join the relevant IEEE working group. Comments on standards should be submitted to the following address: Secretary, IEEE-SA Standards Board 445 Hoes Lane Piscataway, NJ 08854 USA Laws and regulations Users of IEEE Standards document

19、s should consult all applicable laws and regulations. Compliance with the provisions of any IEEE Standards document does not imply compliance to any applicable regulatory requirements. Implementers of the standard are responsible for observing or referring to the applicable regulatory requirements.

20、IEEE does not, by the publication of its standards, intend to urge action that is not in compliance with applicable laws, and these documents may not be construed as doing so. Copyrights IEEE draft and approved standards are copyrighted by IEEE under U.S. and international copyright laws. They are m

21、ade available by IEEE and are adopted for a wide variety of both public and private uses. These include both use, by reference, in laws and regulations, and use in private self-regulation, standardization, and the promotion of engineering practices and methods. By making these documents available fo

22、r use and adoption by public authorities and private users, IEEE does not waive any rights in copyright to the documents. Photocopies Subject to payment of the appropriate fee, IEEE will grant users a limited, non-exclusive license to photocopy portions of any individual standard for company or orga

23、nizational internal use or individual, non-commercial use only. To arrange for payment of licensing fees, please contact Copyright Clearance Center, Customer Service, 222 Rosewood Drive, Danvers, MA 01923 USA; +1 978 750 8400. Permission to photocopy portions of any individual standard for education

24、al classroom use can also be obtained through the Copyright Clearance Center. Updating of IEEE Standards documents Users of IEEE Standards documents should be aware that these documents may be superseded at any time by the issuance of new editions or may be amended from time to time through the issu

25、ance of amendments, corrigenda, or errata. An official IEEE document at any point in time consists of the current edition of the document together with any amendments, corrigenda, or errata then in effect. Every IEEE standard is subjected to review at least every ten years. When a document is more t

26、han ten years old and has not undergone a revision process, it is reasonable to conclude that its contents, although still of some value, do not wholly reflect the present state of the art. Users are cautioned to check to determine that they have the latest edition of any IEEE standard. In order to

27、determine whether a given document is the current edition and whether it has been amended through the issuance of amendments, corrigenda, or errata, visit the IEEE-SA Website at http:/ieeexplore.ieee.org/xpl/standards.jsp or contact IEEE at the address listed previously. For more information about t

28、he IEEE SA or IEEEs standards development process, visit the IEEE-SA Website at http:/standards.ieee.org. Errata Errata, if any, for all IEEE standards can be accessed on the IEEE-SA Website at the following URL: http:/standards.ieee.org/findstds/errata/index.html. Users are encouraged to check this

29、 URL for errata periodically. Patents Attention is called to the possibility that implementation of this standard may require use of subject matter covered by patent rights. By publication of this standard, no position is taken by the IEEE with respect to the existence or validity of any patent righ

30、ts in connection therewith. If a patent holder or patent applicant has filed a statement of assurance via an Accepted Letter of Assurance, then the statement is listed on the IEEE-SA Website at http:/standards.ieee.org/about/sasb/patcom/patents.html. Letters of Assurance may indicate whether the Sub

31、mitter is willing or unwilling to grant licenses under patent rights without compensation or under reasonable rates, with reasonable terms and conditions that are demonstrably free of any unfair discrimination to applicants desiring to obtain such licenses. Essential Patent Claims may exist for whic

32、h a Letter of Assurance has not been received. The IEEE is not responsible for identifying Essential Patent Claims for which a license may be required, for conducting inquiries into the legal validity or scope of Patents Claims, or determining whether any licensing terms or conditions provided in co

33、nnection with submission of a Letter of Assurance, if any, or in any licensing agreements are reasonable or non-discriminatory. Users of this standard are expressly advised that determination of the validity of any patent rights, and the risk of infringement of such rights, is entirely their own res

34、ponsibility. Further information may be obtained from the IEEE Standards Association. Copyright 2015 IEEE. All rights reserved. vi Participants At the time this IEEE guide was completed, the Induced Voltage Work Procedures Working Group had the following membership: Pierre Argaut, Chair Nijam Robert

35、 Uddin, Vice Chair Vctor Antoniello David Bogden John Cooper Dennis DeCosta David Dubois Frank Frentzas Henk Geene Todd Goyette Jim Hunt Dennis Johnson Jeff Joy Kishan Kasondra Matthias Kirchner Don Koonce Arthur Kroese Frdric Lesur Jose Lopez Allen MacPhail Ted Nishioka Mohammad Pasha Rick Piteo Fo

36、rest Rong Darrell Sabatka Mark Smith Hon Suen Austin Tingley Jade Wong Tiebin Zhao Joe Zimnoch The following members of the individual balloting committee voted on this guide. Balloters may have voted for approval, disapproval, or abstention. Saleman Alibhay Earle Bascom III William Bloethe Kenneth

37、Bow Andrew Brown William Byrd Robert Christman Gary Donner Randall Dotson George Gela Randall Groves Lee Herron Lauri Hiivala Werner Hoelzl Jim Hunt Dennis Johnson Albert Kong Jim Kulchisky Paneendra KumarBl Chung-Yiu Lam Michael Lauxman Rachel Mosier Jerry Murphy Michael Newman Joe Nims Christopher

38、 Petrola Robert Resuali Michael Roberts Charles Rogers Bartien Sayogo Dennis Schlender Jerry Smith Peter Tirinzoni Nijam Robert Uddin Roger Verdolin John Vergis Martin Von Herrmann Yingli Wen Kenneth White Jian Yu Tiebin Zhao Joe Zimnoch Copyright 2015 IEEE. All rights reserved. vii When the IEEE-SA

39、 Standards Board approved this guide on 16 February 2015, it had the following membership: John Kulick, Chair Jon Walter Rosdahl, Vice Chair Richard H. Hulett, Past Chair Konstantinos Karachalios, Secretary Peter Balma Farooq Bari Ted Burse Clint Chaplin Stephen Dukes Jean-Philippe Faure Gary Hoffma

40、n Michael Janezic Jeffrey Katz Joseph L. Koepfinger* David J. Law Hung Ling Oleg Logvinov T. W. Olsen Glenn Parsons Ron Petersen Adrian Stephens Peter Sutherland Yatin Trivedi Phil Winston Don Wright Yu Yuan *Member Emeritus Also included are the following nonvoting IEEE-SA Standards Board liaisons:

41、 Richard DeBlasio, DOE Representative Michael Janezic, NIST Representative Patrick Gibbons IEEE-SA Content Production and Management Malia Zaman IEEE-SA Technical Program Operations viii Copyright 2015 IEEE. All rights reserved. Introduction This introduction is not part of IEEE Std 1727-2013/Cor. 1

42、-2015, IEEE Guide for Working Procedures on Underground Transmission Circuits with Induced VoltageCorrigendum 1. This guide establishes induced voltage working procedures for underground transmission circuits. A transmission circuit when de-energized will have an induced voltage when in a common duc

43、t bank with an energized circuit. The induced voltage may be a possible safety hazard. The induced voltage may be determined by modeling the circuits and by measurement. This guide addresses the working procedures to follow when performing work where induced voltage is present. This corrigendum is issued to correct Figure 3 of IEEE Std 1727-2013.