IEEE 1124-2003 en Guide for Analysis and Definition of DC Side Harmonic Performance of HVDC Transmission Systems《HVDC传输系统的直流侧谐波性能的分析和定义》.pdf

《IEEE 1124-2003 en Guide for Analysis and Definition of DC Side Harmonic Performance of HVDC Transmission Systems《HVDC传输系统的直流侧谐波性能的分析和定义》.pdf》由会员分享，可在线阅读，更多相关《IEEE 1124-2003 en Guide for Analysis and Definition of DC Side Harmonic Performance of HVDC Transmission Systems《HVDC传输系统的直流侧谐波性能的分析和定义》.pdf（77页珍藏版）》请在麦多课文档分享上搜索。

1、IEEE Std 1124-2003IEEE Standards1124TMIEEE Guide for Analysis and Definitionof DC Side Harmonic Performance ofHVDC Transmission SystemsPublished by The Institute of Electrical and Electronics Engineers, Inc.3 Park Avenue, New York, NY 10016-5997, USA5 September 2003IEEE Power Engineering SocietySpon

2、sored by theTransmission and b) Computing interference levels that would result with variouspractical dc filter/smoothing reactor designs and the costs of these filters.Keywords: equivalent disturbing current, filters, harmonic currents, harmonic voltages, HVDC transmission systems,induction, induct

3、ive coordination, interference, mitigation methods, mutual impedance, noise, telephone circuitsThe Institute of Electrical and Electronics Engineers, Inc. 3 Park Avenue, New York, NY 10016-5997, USACopyright 2003 by the Institute of Electrical and Electronics Engineers, Inc.IEEE Standards documents

4、are developed within the IEEE Societies and the Standards Coordinating Committees of the IEEE Standards Association (IEEE-SA) Standards Board. The IEEE develops its standards through a consensus development process, approved by the American National Standards Institute, which brings together volunte

5、ers representing varied viewpoints and interests to achieve the final product. Volunteers are not necessarily members of the Institute and serve without compensation. While the IEEE administers the process and establishes rules to promote fairness in the consensus development process, the IEEE does

6、not independently evaluate, test, or verify the accuracy of any of the information or the soundness of any judgments contained in its standards. Use of an IEEE Standard is wholly voluntary. The IEEE disclaims liability for any personal injury, property or other damage, of any nature whatsoever, whet

7、her special, indirect, consequential, or compensatory, directly or indirectly resulting from the publication, use of, or reliance upon this, or any other IEEE Standard document. The IEEE does not warrant or represent the accuracy or content of the material contained herein, and expressly disclaims a

8、ny express or implied warranty, including any implied warranty of merchantability or fitness for a specific purpose, or that the use of the material contained herein is free from patent infringement. IEEE Standards documents are supplied “AS IS.” The existence of an IEEE Standard does not imply that

9、 there are no other ways to produce, test, measure, purchase, market, or provide other goods and services related to the scope of the IEEE Standard. Furthermore, the viewpoint expressed at the time a standard is approved and issued is subject to change brought about through developments in the state

10、 of the art and comments received from users of the standard. Every IEEE Standard is subjected to review at least every five years for revision or reaffirmation, or every ten years for stabilization. When a document is more than five years old and has not been reaffirmed, or more than ten years old

11、and has not been stabilized, it is reasonable to conclude that its contents, although still of some value, do not wholly reflect the present state of the art. Users are cautioned to check to determine that they have the latest edition of any IEEE Standard. In publishing and making this document avai

12、lable, the IEEE is not suggesting or rendering professional or other services for, or on behalf of, any person or entity. Nor is the IEEE undertaking to perform any duty owed by any other person or entity to another. Any person utilizing this, and any other IEEE Standards document, should rely upon

13、his or her independent judgment in the exercise of reasonable care in any given circumstances or, as appropriate, seek the advice of a competent professional in determining the appropriateness of a given IEEE standard. Interpretations: Occasionally questions may arise regarding the meaning of portio

14、ns of standards as they relate to specific applications. When the need for interpretations is brought to the attention of IEEE, the Institute will initiate action to prepare appropriate responses. Since IEEE Standards represent a consensus of concerned interests, it is important to ensure that any i

15、nterpretation has also received the concurrence of a balance of interests. For this reason, IEEE and the members of its societies and Standards Coordinating Committees are not able to provide an instant response to interpretation requests except in those cases where the matter has previously receive

16、d formal consideration. A statement, written or oral, that is not processed in accordance with the IEEE-SA Standards Board Operations Manual shall not be considered the official position of IEEE or any of its committees and shall not be considered to be, nor be relied upon as, a formal interpretatio

17、n of the IEEE. At lectures, symposia, seminars, or educational courses, an individual presenting information on IEEE standards shall make it clear that his or her views should be considered the personal views of that individual rather than the formal position, explanation, or interpretation of the I

18、EEE. Comments for revision of IEEE Standards are welcome from any interested party, regardless of membership affiliation with IEEE. Suggestions for changes in documents should be in the form of a proposed change of text, together with appropriate supporting comments. Recommendations to change the st

19、atus of a stabilized standard should include a rationale as to why a revision or withdrawal is required. Comments and recommendations on standards, and requests for interpretations should be addressed to: Secretary, IEEE-SA Standards Board 445 Hoes Lane Piscataway, NJ 08854-4141 USA Authorization to

20、 photocopy portions of any individual standard for internal or personal use is granted by The Institute of Electrical and Electronics Engineers, Inc., provided that the appropriate fee is paid to Copyright Clearance Center. To arrange for payment of licensing fee, please contact Copyright Clearance

21、Center, Customer Service, 222 Rosewood Drive, Danvers, MA 01923 USA; +1 978 750 8400. Permission to photocopy portions of any individual standard for educational classroom use can also be obtained through the Copyright Clearance Center. Copyright C223 2003 IEEE. All rights reserved. iiiIntroduction(

22、This introduction is not part of IEEE Std 1124-2003, IEEE Guide for the Analysis and Definition of DC-SideHarmonic Performance of HVDC Transmission Systems.)The purpose of this document is to provide guidelines for evaluating and mitigating harmonicinduction eects from high-voltage direct-current (H

23、VDC) lines on the adjacent telephonecommunication lines. Specifically, this guide presents methodology and approach fora) Determining the number of wireline communication circuits that will be aected byunacceptable interference and cost-eective remedial measures.b) Computing interference levels that

24、 would result with various practical dc filter/smoothingreactor designs and the costs of these filters.ParticipantsAt the time this guide was completed, the IEEE Working Group on HVDC Harmonics, which wassponsored by the DC and FACTS Subcommittee of the Transmission however, statistical methodsand/o

25、r approximation are necessary in order to keep the number of computation cases for harmoniccurrent profiles on the dc transmission line to a reasonable level of eort.Copyright C223 2003 IEEE. All rights reserved. 11The numbers in square brackets correspond to those of the bibliography in Annex A.1.1

26、 ScopeThis guide contains information and recommendations pertaining to the analysis and specification ofthe performance on the dc side of a high-voltage direct-current converter station concerning theelectrical noise at harmonic frequencies up to 5kHz generated by converter stations in a dctransmis

27、sion system. This guide also contains information and suggestions pertaining to measurementof dc filter performance and noise level induced in wireline communications circuits from harmoniccurrents on dc transmission lines.1.2 PurposeInductive coordination studies for dc transmission lines have two

28、basic aspects:a) Determination of the number of wireline communication circuits that will suer unacceptableinterference and the costs that would be involved in remedial measures applied to the aectedwireline communication circuits.b) Computation of interference levels that would result with various

29、practical dc filter/smoothingreactor designs and the costs of these filters.The optimum solution can be obtained by a cost/performance study. A substantial part of the workinvolves identifying all wireline communication circuits in the vicinity of planned dc transmission linesand calculating probabl

30、e levels of induced interference for each circuit. These calculations are tediousand time-consuming, even using available computer programs, due to the detailed calculationsinvolved and determining the exact parameters of each exposure. This can be further complicated bychanges to the dc transmissio

31、n line route (due to factors involved in finalizing the dc line right-of-way),which changes the wireline communication circuit exposures to be analyzed; changes in dc filterdesigns producing changes in harmonic current profiles on the dc transmission lines; diculties inreaching agreement between pow

32、er and telephone companies on limits of allowable inducedinterference; and short dc project construction schedules.Reaching an optimum solution can be a lengthy, iterative process. Each dc project is unique, so that asolution used previously on a similar dc transmission project is not necessarily th

33、e optimum solutionfor the dc project under study. However, by using a simple, systematic approach to the problem and byselecting boundaries to the variation of each relevant operating parameter, the required studies can bestarted early in the project and a satisfactory conclusion reached relatively

34、quickly.One approach (Patterson and Fletcher B18) involves de-coupling the calculation of dc filtercharacteristics and harmonic current profiles on the dc transmission line (the power system analysis)from the calculation of coupling factors at harmonic frequencies between the dc transmission line an

35、deach adjacent wireline communications circuit due to harmonic currents on the dc transmission line(the communications system analysis).2. ReferencesWhen the following standards are superseded by an approved revision, the revision shall apply.IEEE Std 1137TM-1991 (Rea 1998), IEEE Guide for the Imple

36、mentation of Inductive CoordinationMitigation Techniques and Applications.2,32 Copyright C223 2003 IEEE. All rights reserved.2The IEEE standards or products referred to in Clause 2 are trademarks owned by the Institute of Electrical and ElectronicsEngineers, Inc.3IEEE publications are available from

37、 the Institute of Electrical and Electronics Engineers, Inc., 445 Hoes Lane, P.O. Box 1331,Piscataway, NJ 08855-1331, USA (http:/www.standards.ieee.org/).IEEEStd 1124-2003 IEEE GUIDE FOR THE ANALYSIS AND DEFINITION OF3. Explanation of terms3.1 DC harmonicsThis term refers to the ac harmonic content

38、of the dc voltage or current of an HVDC system, as definedin The Authoritative Dictionary of IEEE Standards Terms, Seventh Edition B8. In an ideal bridgeconverter, the dc voltage harmonics have frequencies of only even multiples of the fundamentalfrequency at characteristic frequencies; however, in

39、practice other even and odd multiples offundamental frequency (at noncharacteristic frequencies) can also appear due to system imbalancesand stray capacitances.3.2 Ideal converterAn ideal converter is considered to be a converter that has balanced sinusoidal voltage, circuitimpedances, firing angle,

40、 and no stray capacitance, and smooth dc current for purposes ofcommutation, etc.3.3 Harmonic orderThe order of a harmonic of the dc voltage/current is the ratio of its frequency to the fundamentalfrequency on the ac side of the converter.3.4 Characteristic/noncharacteristic harmonicsIn an ideal con

41、verter, the characteristic harmonics are those harmonics that are based on theoreticalwaveforms of dc voltage of a converter and can be expressed in terms of the pulse number of theconverter; for example, for a six-pulse converter, the harmonic order can be expressed as 6n, where n isan integer and,

42、 in general, the expression would be pn, where p is the pulse number. All otherharmonics not defined by such an expression are traditionally termed as noncharacteristic harmonics.Noncharacteristic harmonics usually are relatively small. However, for a practical converter, such adefinition is not app

43、licable, and a more precise approach is to express harmonics in terms of triplenand nontriplen harmonics (see 3.5).3.5 Triplen harmonicsTriplen harmonics are those harmonics that are multiples of the third harmonic; for example, 3, 6, 9,12, 15, . . . and can be classified as either odd or even. The

44、even triplen harmonics, which are multiplesof the converter pulse number (for example, 12, 24, . . . for a twelve-pulse converter), are the same ascharacteristic harmonics of an ideal converter and flow through the poles of the converter (pole modein a balanced system). However, due to imbalances in

45、 the poles, a residual even triplen harmoniccurrent may flow through a ground return path. Other triplen harmonics (odd and even) are zerosequence type and flow either through the ground mat or the neutral ground (refer to 5.6).Non-triplen harmonics are those harmonics that are neither multiples of

46、the third harmonic nor theconverter pulse number and can appear due to system or converter imbalances.3.6 Equivalent disturbing current (Ieq)Equivalent disturbing current (Ieq) is used to denote a single harmonic current at a reference frequency(usually 1000Hz for the 60Hz system) that would produce

47、 the same interference in a telephone line asproduced by all individual harmonics. The equivalent disturbing current takes into account the CCopyright C223 2003 IEEE. All rights reserved. 3IEEEDC-SIDE HARMONIC PERFORMANCE OF HVDC TRANSMISSION SYSTEMS STD 1124-2003message weighting factor (Cn) and a

48、frequency dependence factor (Hn) for mutual coupling to thetelephone line.3.7 Harmonic performanceThe term harmonic performance refers to the performance of the harmonic filtering system on the dcside in mitigating the flow of harmonic currents into the dc line. The harmonic performance may beexpres

49、sed in terms of the equivalent disturbing current (usually in mA) or the induced voltage in atelephone line (usually in mV/km), or in terms of the individual or total harmonic current levels. Thelatter method of specifying is not very commonly used in the U.S. and Canada. The specifiedperformance becomes the basis for the design of the dc harmonic filtering system.The harmonic performance is often specified separately for bipolar and monopolar modes ofoperation, since the monopolar operation is usually for only short duration and a relatively lowerperformance can be tolerated.3