IEC 62005-9-2-2007 Reliability of fibre optic interconnecting devices and passive optical components - Part 9-2 Reliability qualification for single fibre optic.pdf

《IEC 62005-9-2-2007 Reliability of fibre optic interconnecting devices and passive optical components - Part 9-2 Reliability qualification for single fibre optic.pdf》由会员分享，可在线阅读，更多相关《IEC 62005-9-2-2007 Reliability of fibre optic interconnecting devices and passive optical components - Part 9-2 Reliability qualification for single fibre optic.pdf（36页珍藏版）》请在麦多课文档分享上搜索。

1、 INTERNATIONAL STANDARD IECCEINORME INTERNATIONALE62005-9-2First editionPremire dition2007-05Reliability of fibre optic interconnecting devices and passive optical components Part 9-2: Reliability qualification for single fibre optic connector sets Single mode Fiabilit des dispositifs dinterconnexio

2、n et des composants optiques passifs fibres optiques Partie 9-2: Qualification relative la fiabilit pour les ensembles de connecteurs une seule fibre optique Unimodal Reference number Numro de rfrence IEC/CEI 62005-9-2:2007 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2007 IEC, Geneva, Switzerl

3、and All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country o

4、f the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, auc

5、une partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le

6、copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch Abo

7、ut the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant revie

8、w by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,). It als

9、o gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available on-line and also by email. Customer Service Centre: www.

10、iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 A propos de la CEI La Commission Electrotechnique Internationale (CE

11、I) est la premire organisation mondiale qui labore et publie des normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous

12、 possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue en-ligne de la CEI vous permet deffectuer des recherches en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Il

13、 donne aussi des informations sur les projets et les publications retires ou remplaces. Just Published CEI: www.iec.ch/online_news/justpub Restez inform sur les nouvelles publications de la CEI. Just Published dtaille deux fois par mois les nouvelles publications parues. Disponible en-ligne et aussi

14、 par email. Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du Service clients ou contactez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 INTERNATIO

15、NAL STANDARD IECCEINORME INTERNATIONALE62005-9-2First editionPremire dition2007-05Reliability of fibre optic interconnecting devices and passive optical components Part 9-2: Reliability qualification for single fibre optic connector sets Single mode Fiabilit des dispositifs dinterconnexion et des co

16、mposants optiques passifs fibres optiques Partie 9-2: Qualification relative la fiabilit pour les ensembles de connecteurs une seule fibre optique Unimodal For price, see current cataloguePour prix, voir catalogue en vigueur PRICE CODE CODE PRIX P Commission Electrotechnique InternationaleInternatio

17、nal Electrotechnical Commission 2 62005-9-2 IEC:2007 CONTENTS FOREWORD.3 INTRODUCTION.5 1 Scope.6 2 Normative references .6 3 Terms, definitions and abbreviations 8 3.1 Terms and definitions 8 3.2 Abbreviations 8 4 General requirements.8 4.1 Overview .8 4.2 Test sample definition .8 4.3 Service envi

18、ronments 8 4.4 Tests.9 4.5 Details.9 4.6 Requirements9 4.7 Groupings/sequences9 4.8 Sample size 9 4.9 Pass/fail criteria 9 4.10 Reference product definition10 4.11 Reliability standard test report.10 5 Reliability qualification tests for fibre optic connectors10 Figure 1 Reliability qualification te

19、sts sequence and grouping required for fibre optic connector sets used in the controlled service environment of Category C .13 Figure 2 Reliability qualification tests sequence and grouping required for fibre optic connector sets used in the uncontrolled service environment of Category U .16 Table 1

20、 Categories of service environments for fibre optic connectors .8 Table 2 Allowable number defective and corresponding minimum sample size for 20 % LTPD .9 Table 3 Reliability qualification tests required for fibre optic connector sets used in the controlled service environment of Category C .11 Tab

21、le 4 Reliability qualification tests required for fibre optic connectors used in the uncontrolled environment of Category U .14 62005-9-2 IEC:2007 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ RELIABILITY OF FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE OPTICAL COMPONENTS Part 9-2: Reliability qua

22、lification for single fibre optic connector sets Single mode FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co

23、-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred

24、to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this

25、 preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international

26、 consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable eff

27、orts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publicat

28、ions transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and

29、 cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts a

30、nd members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Public

31、ation or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Public

32、ation may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 62005-9-2 has been prepared by subcommittee 86B: Fibre optic interconnecting devices and passive components, of IEC technical committee 86: Fibre opt

33、ics. This standard cancels and replaces IEC/PAS 62005-9-2, published in 2003. This first edition constitutes a technical revision. 4 62005-9-2 IEC:2007 The text of this standard is based on the following documents: FDIS Report on voting 86B/2495/FDIS 86B/2536/RVD Full information on the voting for t

34、he approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts of the IEC 62005 series, published under the general title Reliability of fibre optic interconnecti

35、ng devices and passive optical components, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publicat

36、ion. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. 62005-9-2 IEC:2007 5 INTRODUCTION Both performance qualification standards and reliability qualification standards (RQS) define a set of prescribed conditions and contain a series or a set o

37、f tests and measurements (which may or may not be grouped into a specific schedule) with clearly defined conditions, severities and pass/fail criteria. The tests are intended to be run on a once-off basis to prove the products ability to satisfy the performance or reliability requirements of a speci

38、fic application, market sector or user group. The remaining parts of this series contain those sets of reliability criteria that have been standardized for international use. A product that has been shown to meet all the requirements of a reliability standard may be declared as complying with that r

39、eliability standard. It is recognised that component reliability qualification could be accomplished in alternative ways. The procedures in this standard are a baseline, but other qualification methods could prove to be more cost-effective. Alternative methods may be included in future revisions of

40、this standard if they are demonstrated to be effectively equivalent to the baseline procedures. Compliance with an RQS demonstrates that a product has met its optical and mechanical performance over the duration of the applied test programs. Consistency of manufacture should be maintained using a re

41、cognized Quality Assurance program. 6 62005-9-2 IEC:2007 RELIABILITY OF FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE OPTICAL COMPONENTS Part 9-2: Reliability qualification for single fibre optic connector sets Single mode 1 Scope This part of IEC 62005 applies to fibre optic connector sets and co

42、ntains the minimum test and measurement requirements and severities which a fibre optic connector set shall satisfy in order to be qualified as meeting the requirements for reliability qualification of singlemode fibre optic connectors with single fibre cylindrical ferrule PC polished as defined in

43、the IEC 61754 series and used in controlled and uncontrolled environments (categories C and U) as defined in IEC 61753-1. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undate

44、d references, the latest edition of the referenced document (including any amendments) applies. IEC 60793-1, Optical fibres Measurement methods and test procedures IEC 61300 (all parts), Fibre optic interconnecting devices and passive components Basic test and measurement procedures IEC 61300-2-1, F

45、ibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-1: Tests Vibration (sinusoidal) IEC 61300-2-2, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-2: Tests Mating durability IEC 61300-2-4, Fibr

46、e optic interconnecting devices and passive components Basic test and measurement procedures Part 2-4: Tests Fibre/cable retention IEC 61300-2-6, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-6 Tests Tensile strength of coupling mechanism IEC

47、 61300-2-18, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-18: Tests Dry heat High temperature endurance IEC 61300-2-19, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-19: Tests Damp he

48、at (steady state) 62005-9-2 IEC:2007 7 IEC 61300-2-22, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-22: Tests Change of temperature IEC 61300-3-3, Fibre optic interconnecting devices and passive components Basic test and measurement procedur

49、es Part 3-3: Examinations and measurements Active monitoring of changes in attenuation and return loss IEC 61300-3-4, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-4: Examinations and measurements Attenuation IEC 61300-3-6, Fibre optic intercon