IEC 61935-2-2010 Specification for the testing of balanced and coaxial information technology cabling - Part 2 Cords as specified in ISO IEC 11801 and related s.pdf

《IEC 61935-2-2010 Specification for the testing of balanced and coaxial information technology cabling - Part 2 Cords as specified in ISO IEC 11801 and related s.pdf》由会员分享，可在线阅读，更多相关《IEC 61935-2-2010 Specification for the testing of balanced and coaxial information technology cabling - Part 2 Cords as specified in ISO IEC 11801 and related s.pdf（60页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 61935-2 Edition 3.0 2010-07 INTERNATIONAL STANDARD NORME INTERNATIONALE Specification for the testing of balanced and coaxial information technology cabling Part 2: Cords as specified in ISO/IEC 11801 and related standards Spcification relative aux essais des cblages symtriques et coaxiaux des

2、technologies de linformation Partie 2: Cordons tels que spcifis dans lISO/CEI 11801 et normes associes IEC 61935-2:2010 colour inside THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2010 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be re

3、produced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about ob

4、taining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que c

5、e soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publicat

6、ion, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organ

7、ization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendm

8、ent might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, withdrawn and replaced publications. IEC Just Published:

9、www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available on-line and also by email. Electropedia: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing m

10、ore than 20 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary online. Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need furth

11、er assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des normes internationales pour to

12、ut ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue des

13、 publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue en-ligne de la CEI vous permet deffectuer des recherches en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Il donne aussi des informations sur les projets et les publications retires ou remplaces. Just Pu

14、blished CEI: www.iec.ch/online_news/justpub Restez inform sur les nouvelles publications de la CEI. Just Published dtaille deux fois par mois les nouvelles publications parues. Disponible en-ligne et aussi par email. Electropedia: www.electropedia.org Le premier dictionnaire en ligne au monde de ter

15、mes lectroniques et lectriques. Il contient plus de 20 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International en ligne. Service Clients: www.iec.ch/webstore/custserv/custserv_entry

16、-f.htm Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du Service clients ou contactez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC 61935-2 Edition 3.0 2010-07 INTERNATIONAL STANDARD NORME INTERNATIONALE Specif

17、ication for the testing of balanced and coaxial information technology cabling Part 2: Cords as specified in ISO/IEC 11801 and related standards Spcification relative aux essais des cblages symtriques et coaxiaux des technologies de linformation Partie 2: Cordons tels que spcifis dans lISO/CEI 11801

18、 et normes associes INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE U ICS 33.040.20; 33.120.20 PRICE CODE CODE PRIX ISBN 978-2-88912-001-7 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Interna

19、tionale colour inside 2 61935-2 IEC:2010 CONTENTS FOREWORD.4 INTRODUCTION.6 1 Scope.7 2 Normative references .7 3 Terms and definitions .8 4 General requirements and test configuration 8 4.1 Cable and connector design 8 4.2 Balanced cord, cable and connector tests .8 4.3 Test configuration and equip

20、ment8 4.4 Balanced cord tests requirements .9 5 Acceptance tests 10 5.1 Visual inspection .10 5.2 Wire map.11 5.3 Propagation delay .12 5.4 Delay skew12 5.5 Insertion loss.12 5.6 Return loss12 5.7 Near end crosstalk (NEXT)13 5.8 Assumptions used in the development of cord requirements16 6 Balanced c

21、ord test procedure Network analyser test configuration 16 7 Periodic tests .17 7.1 General .17 7.2 Tensile strength 17 7.3 Flexure18 7.4 Bending.19 7.5 Twisting.19 7.6 Crushing .20 7.7 Dust test21 7.8 Coupling attenuation .23 7.9 Climatic sequence.24 8 Test head requirements24 8.1 General .24 8.2 Mi

22、nimum requirements for all test head designs 24 8.3 Additional FEXT requirements for balanced connector compatible test heads25 8.4 Additional return loss requirements for balanced connector compatible test heads25 8.5 NEXT loss centering requirements for balanced connector compatible test heads25 B

23、ibliography27 61935-2 IEC:2010 3 Figure 1 Test configuration for balanced cord for NEXT and return loss measurements 9 Figure 2 Correct pairing .11 Figure 3 Incorrect pairing.11 Figure 4 Initial marking of the cable sheath17 Figure 5 Final visual inspection17 Figure 6 Fixture for balanced cord flexu

24、re test .18 Figure 7 Bending test: assembly in U shape 19 Figure 8 Twisting test: assembly in U shape 20 Figure 9 Fixture for cable crushing test 21 Figure 10 Measuring device.23 Figure 11 Centering of NEXT properties of the balanced connector test head 26 Table 1 Return loss requirements 13 Table 2

25、 Balanced cord return loss requirements at key frequencies .13 Table 3 Category 5 balanced cord NEXT requirements at key frequencies.15 Table 4 Category 6 balanced cord NEXT requirements at key frequencies.15 Table 5 Category 6 Abalanced cord NEXT requirements at key frequencies 15 Table 6 Category

26、7 balanced cord NEXT requirements at key frequencies.15 Table 7 Category 7 Abalanced cord NEXT requirements at key frequencies 15 Table 8 Assumptions for cabling components used in the development of NEXT and return loss requirements .16 Table 9 Coupling attenuation limits 23 4 61935-2 IEC:2010 INTE

27、RNATIONAL ELECTROTECHNICAL COMMISSION _ SPECIFICATION FOR THE TESTING OF BALANCED AND COAXIAL INFORMATION TECHNOLOGY CABLING Part 2: Cords as specified in ISO/IEC 11801 and related standards FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardizati

28、on comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes Internation

29、al Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in th

30、is preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the tw

31、o organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have th

32、e form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinter

33、pretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national

34、or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carri

35、ed out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Comm

36、ittees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn t

37、o the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be

38、held responsible for identifying any or all such patent rights. International Standard IEC 61935-2 has been prepared by IEC technical committee 46: Cables, wires, waveguides, R.F. connectors, R.F. and microwave passive components and accessories. This third edition cancels and replaces the second ed

39、ition published in 2005. This third edition of IEC 61935-2 differs from the second edition in that it covers category 6 Ato category 7 Acords as defined in ISO/IEC 11801. 61935-2 IEC:2010 5 The text of this standard is based on the following documents: FDIS Report on voting 46/351/FDIS 46/364/RVD Fu

40、ll information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. The French version of this standard has not been voted upon. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts of t

41、he IEC 61935 series, under the general title: Specification for the testing of balanced and coaxial information technology cabling, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability indicated on the IEC web site

42、 under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. A bilingual version of this publication may be issued at a later date. IMPORTANT The colour inside logo on the cove

43、r page of this publication indicates that it contains colours which are considered to be useful for the correct understanding of its contents. Users should therefore print this document using a colour printer. 6 61935-2 IEC:2010 INTRODUCTION Balanced cords are constructed for connecting equipment us

44、ing free connectors according to IEC 60603-7 series, IEC 61076-3-104 and IEC 61076-3-110. It is known that connecting hardware performance is subject to influence by the properties of the free connector termination and therefore balanced cords should be tested to determine the quality of the assembl

45、y. Moreover, the performance of balanced cords may differ due to the performances of the involved separate components depending upon the efficiency of the manufacturing procedure. Manufacturing procedures also impact upon the reliability of these balanced cords. Therefore, the primary object of this

46、 standard is to provide test methods to ensure compatibility of balanced cords to be used in cabling according to ISO/IEC 11801. Another object is to provide test methods and associated requirements to demonstrate the performance and reliability of these balanced cords during their operational lifet

47、ime. The test methods described in this standard may also be used for any balanced cords that include twisted pairs terminated at each end. 61935-2 IEC:2010 7 SPECIFICATION FOR THE TESTING OF BALANCED AND COAXIAL INFORMATION TECHNOLOGY CABLING Part 2: Cords as specified in ISO/IEC 11801 and related

48、standards 1 Scope This International Standard provides methods to ensure compatibility of balanced cords to be used in cabling according to ISO/IEC 11801 and provides test methods and associated requirements to demonstrate the performance and reliability of these balanced cords during their operatio

49、nal lifetime. This International Standard may also be used for providing test methods for assessing the behaviour of other balanced cords. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced docu