IEC 61300-2-19-2012 Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-19 Tests - Damp heat (steady sta.pdf

《IEC 61300-2-19-2012 Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-19 Tests - Damp heat (steady sta.pdf》由会员分享，可在线阅读，更多相关《IEC 61300-2-19-2012 Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-19 Tests - Damp heat (steady sta.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 61300-2-19 Edition 3.0 2012-11 INTERNATIONAL STANDARD NORME INTERNATIONALE Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-19: Tests Damp heat (steady state) Dispositifs dinterconnexion et composants passifs fibres optiques Mthodes fondame

2、ntales dessais et de mesures Partie 2-19: Essais Chaleur humide (tat continu) IEC 61300-2-19:2012 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2012 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or

3、by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this pu

4、blication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectroniq

5、ue ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs

6、 ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organizati

7、on that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment m

8、ight have been published. Useful links: IEC publications search - www.iec.ch/searchpub The advanced search enables you to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Jus

9、t Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms

10、 containing more than 30 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication o

11、r need further assistance, please contact the Customer Service Centre: csciec.ch. A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux techn

12、ologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub L

13、a recherche avance vous permet de trouver des publications CEI en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform sur les

14、 nouvelles publications de la CEI. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 termes

15、 et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez

16、 des questions contactez-nous: csciec.ch. IEC 61300-2-19 Edition 3.0 2012-11 INTERNATIONAL STANDARD NORME INTERNATIONALE Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-19: Tests Damp heat (steady state) Dispositifs dinterconnexion et composant

17、s passifs fibres optiques Mthodes fondamentales dessais et de mesures Partie 2-19: Essais Chaleur humide (tat continu) INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE J ICS 33.180.20 PRICE CODE CODE PRIX ISBN 978-2-83220-469-6 Registered trademark of the Internat

18、ional Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. 2 61300-2-19 IEC:2012

19、 CONTENTS FOREWORD . 3 1 Scope . 5 2 Normative references . 5 3 General description 5 4 Apparatus . 5 4.1 Chamber . 5 4.2 Steam . 6 4.3 Optical measurements . 6 4.4 Positioning and mounting of the specimen . 6 5 Procedure. 7 5.1 General . 7 5.2 Preconditioning . 7 5.3 Initial examinations and measur

20、ements . 7 5.4 Conditioning 7 5.5 Recovery . 8 5.6 Final examinations and measurements 8 6 Severity 8 7 Details to be specified 8 Table 1 Severities 8 61300-2-19 IEC:2012 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS BASIC TEST AND MEASUREME

21、NT PROCEDURES Part 2-19: Tests Damp heat (steady state) FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-oper

22、ation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as

23、 “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this pre

24、paration. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international con

25、sensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts

26、 are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications

27、 transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Indepen

28、dent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No lia

29、bility shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (inc

30、luding legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application o

31、f this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61300-2-19 has been prepared by subcommittee

32、 SC86B: Fibre optic interconnecting devices and passive components, of IEC technical committee 86: Fibre optics. This third edition cancels and replaces the second edition published in 2005. It constitutes a technical revision. The changes with respect to the previous edition are to reconsider the s

33、everities and details to be specified. 4 61300-2-19 IEC:2012 The text of this standard is based on the following documents: FDIS Report on voting 86B/3492/FDIS 86B/3536/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above ta

34、ble. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. The list of all parts of IEC 61300 series, published under the general title, Fibre optic interconnecting and passive components Basic test and measurement procedures, can be found on the IEC website. The commi

35、ttee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised editi

36、on, or amended. 61300-2-19 IEC:2012 5 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS BASIC TEST AND MEASUREMENT PROCEDURES Part 2-19: Tests Damp heat (steady state) 1 Scope This part of IEC 61300 details a procedure for determining the suitability of a fibre optic device to withstand the

37、 environmental condition of high humidity and high temperature which may occur in actual use, storage and/or transport. The test is primarily intended to permit the observation of effects of high humidity at constant temperature over a given period. Absorption of moisture may result in swelling that

38、 would destroy functional utility, cause loss of physical strength, and cause changes in other important mechanical properties. Degradation of optical properties may also occur. Although not necessarily intended as a simulated tropical test, this test can, nevertheless, be useful in determining mois

39、ture absorption of insulating or covering materials. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest ed

40、ition of the referenced document (including any amendments) applies. IEC 60068-2-78, Environmental testing Part 2-78: Tests Test Cab: Damp heat, steady state IEC 61300-3-1, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-1: Examinations and mea

41、surements Visual examination IEC 61300-3-3, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-3: Examinations and measurements Active monitoring of changes in attenuation and return loss IEC 61300-3-4, Fibre optic interconnecting devices and pass

42、ive components Basic test and measurement procedures Part 3-4: Examinations and measurements Attenuation 3 General description This procedure is conducted in accordance with IEC 60068-2-78, Test Cab. The specimen is placed in a chamber and subjected to a damp-heat environment which is maintained at

43、a given temperature and relative humidity for a specified duration, as specified in the relevant specification. 4 Apparatus 4.1 Chamber The apparatus consists of an environmental chamber in accordance with IEC 60068-2-78, test Cab. The chamber shall be capable of housing the specimen and shall be so

44、 constructed that: 6 61300-2-19 IEC:2012 a) it can produce the temperature and relative humidity given in Table 1; b) it is capable of providing controlled conditions of temperature, relative humidity during testing, and the ramp-up to, and ramp-down from, specified test conditions; c) the temperatu

45、re and humidity of the chamber can be monitored by means of sensing devices located in the working space, and/or other areas giving the same results (e.g. a steam generator); d) the enclosed atmosphere can be expelled from the chamber by the water-vapour prior to the commencement of testing; e) cond

46、ensed water is not allowed to fall on the specimen; f) the materials used in the construction shall not cause any corrosion of the specimen, or degradation of the quality of the humidifying water. The temperature tolerance of 2 C is intended to take account of absolute errors in the measurement, flu

47、ctuations of the chamber temperature at any point, and variations between all points within the working space. However, in order to maintain the relative humidity within the specified tolerance of 5 %, it is necessary to keep the difference between any two points in the working space (at any instant

48、) within narrower limits. The specified humidity tolerance will be exceeded if such temperature differences exceed 1,5 C. It is also necessary to restrict the short-term temperature fluctuations due to cycling of the chamber heater to a similar value. The specimen should not significantly impede the

49、 vapour flow. Condensation shall not be allowed to form on the specimen at any time during the test. 4.2 Steam Use steam or distilled, demineralized or deionized water to obtain the specified humidity. No rust or corrosion contaminants shall be imposed on the specimen by the test facility. Before the water is placed in the humidifier, all internal parts of the chamber shall be cleaned. The w