IEC 60384-14-2013 Fixed capacitors for use in electronic equipment - Part 14 Sectional specification - Fixed capacitors for electromagnetic interference suppres.pdf

《IEC 60384-14-2013 Fixed capacitors for use in electronic equipment - Part 14 Sectional specification - Fixed capacitors for electromagnetic interference suppres.pdf》由会员分享，可在线阅读，更多相关《IEC 60384-14-2013 Fixed capacitors for use in electronic equipment - Part 14 Sectional specification - Fixed capacitors for electromagnetic interference suppres.pdf（136页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 60384-14 Edition 4.0 2013-06 INTERNATIONAL STANDARD NORME INTERNATIONALE Fixed capacitors for use in electronic equipment Part 14: Sectional specification Fixed capacitors for electromagnetic interference suppression and connection to the supply mains Condensateurs fixes utiliss dans les quipem

2、ents lectroniques Partie 14: Spcification intermdiaire Condensateurs fixes dantiparasitage et raccordement lalimentation IEC60384-14:2013 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2013 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may b

3、e reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry abou

4、t obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme q

5、ue ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publ

6、ication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commissio

7、n (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest

8、 edition, a corrigenda or an amendment might have been published. Useful links: IEC publications search - www.iec.ch/searchpub The advanced search enables you to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, repl

9、aced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dicti

10、onary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to giv

11、e us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a tra

12、it llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de p

13、ublications CEI - www.iec.ch/searchpub La recherche avance vous permet de trouver des publications CEI en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.ie

14、c.ch/justpublished Restez inform sur les nouvelles publications de la CEI. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectr

15、iques. Il contient plus de 30 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentair

16、es sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 60384-14 Edition 4.0 2013-06 INTERNATIONAL STANDARD NORME INTERNATIONALE Fixed capacitors for use in electronic equipment Part 14: Sectional specification Fixed capacitors for electromagnetic interference suppressi

17、on and connection to the supply mains Condensateurs fixes utiliss dans les quipements lectroniques Partie 14: Spcification intermdiaire Condensateurs fixes dantiparasitage et raccordement lalimentation INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE XB ICS 31.060

18、.10 PRICE CODE CODE PRIX ISBN 978-2-83220-828-1 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer q

19、ue vous avez obtenu cette publication via un distributeur agr. 2 60384-14 IEC:2013 CONTENTS FOREWORD . 6 1 General 8 1.1 Scope 8 1.2 Object . 8 1.3 Normative references 8 1.4 Information to be given in a detail specification . 9 1.4.1 Outline drawing and dimensions 9 1.4.2 Mounting . 9 1.4.3 Ratings

20、 and characteristics 10 1.4.4 Marking . 10 1.5 Terms and definitions 10 1.6 Marking . 15 1.6.1 Marking of capacitors 15 1.6.2 Marking of packaging. 15 1.6.3 Additional marking . 16 1.7 Classification of Class X and Class Y capacitors . 16 1.7.1 Classification of X capacitors . 16 1.7.2 Classificatio

21、n of Y capacitors . 16 2 Preferred ratings and characteristics 17 2.1 Preferred characteristics . 17 2.1.1 Preferred climatic categories . 17 2.2 Preferred values of ratings 18 2.2.1 Nominal capacitance (CN) . 18 2.2.2 Tolerance on nominal capacitance . 18 2.2.3 Rated voltage (UR) 18 2.2.4 Nominal r

22、esistance (RN) 18 2.2.5 Rated temperature . 18 2.2.6 Passive flammability 18 2.3 Requirements for sleeving, tape, tubing and wire insulation . 18 3 Assessment procedures . 19 3.1 Primary stage of manufacture 19 3.2 Structurally similar components . 19 3.3 Certified records of released lots . 19 3.4

23、Approval testing 19 3.4.1 Safety tests only approval 19 3.4.2 Qualification approval 19 3.4.3 Qualification approval on the basis of the fixed sample size procedure 19 3.5 Quality conformance inspection . 30 3.5.1 Formation of inspection lots . 30 3.5.2 Test schedule 31 3.5.3 Delayed delivery 31 3.5

24、.4 Assessment level . 31 4 Test and measurement procedures . 32 4.1 Visual examination and check of dimensions . 32 4.1.1 Creepage distances and clearances 32 60384-14 IEC:2013 3 4.2 Electrical tests . 33 4.2.1 Voltage proof . 33 4.2.2 Capacitance 35 4.2.3 Tangent of loss angle 35 4.2.4 Resistance (

25、Equivalent Series Resistance (ESR) (for RC units only) 36 4.2.5 Insulation resistance 36 4.3 Robustness of terminations . 37 4.4 Resistance to soldering heat . 37 4.4.1 Test conditions 37 4.4.2 Final inspection, measurements and requirements 38 4.5 Solderability 38 4.5.1 Test conditions 38 4.5.2 Req

26、uirements 38 4.6 Rapid change of temperature 38 4.6.1 Final inspection . 38 4.7 Vibration 38 4.7.1 Test conditions 39 4.7.2 Final inspection . 39 4.8 Bump 39 4.8.1 Test conditions 39 4.8.2 Final inspection, measurements and requirements 39 4.9 Shock 39 4.9.1 Test conditions 39 4.9.2 Final inspection

27、, measurements and requirements 40 4.10 Container sealing 40 4.10.1 Test conditions 40 4.10.2 Requirements 40 4.11 Climatic sequence . 40 4.11.1 Initial measurements . 40 4.11.2 Dry heat 41 4.11.3 Damp heat, cyclic, test Db, first cycle 41 4.11.4 Cold 41 4.11.5 Damp heat, cyclic, test Db, remaining

28、cycles . 41 4.11.6 Final inspection, measurements and requirements 41 4.12 Damp heat, steady state 41 4.12.1 Initial measurements . 42 4.12.2 Test conditions 42 4.12.3 Final inspection, measurements and requirements 42 4.13 Impulse voltage . 42 4.13.1 Initial measurements . 42 4.13.2 Test conditions

29、 43 4.13.3 Requirements 43 4.14 Endurance . 44 4.14.1 Test conditions 44 4.14.2 Initial measurements . 44 4.14.3 Endurance for Class X capacitors and RC units containing Class X capacitors 44 4.14.4 Endurance for Class Y capacitors and RC units containing Class Y capacitors 45 4 60384-14 IEC:2013 4.

30、14.5 Endurance for the lead-through arrangements . 45 4.14.6 Test conditions Combined voltage/current tests 45 4.14.7 Final inspection, measurements and requirements 46 4.15 Charge and discharge . 46 4.15.1 Initial measurements . 46 4.15.2 Test conditions 46 4.15.3 Final measurements and requirement

31、s 47 4.16 Radiofrequency characteristics 47 4.17 Passive flammability test . 47 4.17.1 Testing according to IEC 60384-1 47 4.17.2 Alternative passive flammability test 48 4.18 Active flammability test 49 4.18.3 Adjustment of Ui50 4.18.4 Requirements 50 4.19 Component solvent resistance (if applicabl

32、e) . 50 4.20 Solvent resistance of the marking 51 Annex A (normative) Circuit for the impulse voltage test 52 Annex B (normative) Circuit for the endurance test 54 Annex C (normative) Circuit for the charge and discharge test . 55 Annex D (normative) Declaration of design (confidential to the manufa

33、cturer and the certification body) . 56 Annex E (informative) Pulse test circuits 57 Annex F (normative) Particular requirements for safety test of surface-mounting capacitors . 59 Annex G (informative) Capacitance ageing of fixed capacitors of ceramic dielectric, Class 2 . 62 Bibliography 64 Figure

34、 1 Two-terminal EMI suppression capacitor 11 Figure 2 RC unit. 11 Figure 3 Lead-through capacitor (coaxial) 11 Figure 4 Lead-through capacitors . 12 Figure 5 By-pass capacitors . 13 Figure 6 Test duration (s) . 30 Figure 7 Impulse wave form . 43 Figure 8 Typical circuit for pulse loading of capacito

35、rs under a.c. voltage 49 Figure 9 Fundamental a.c. wave with randomly, not synchronized, superimposed high-voltage pulse. 50 Figure A.1 Impulse voltage test circuit . 52 Figure B.1 Endurance test circuit . 54 Figure C.1 Charge and discharge test circuit 55 Figure F.1 Example of test substrate for sa

36、fety test according to Table F.1 61 Table 1 Classification of Class X capacitors . 16 Table 2 Classification of Class Y capacitors . 17 Table 3 Sampling plan Tests concerning safety requirements only 21 60384-14 IEC:2013 5 Table 4 Sampling plan Safety and performance tests qualification approval Ass

37、essment level DZ 22 Table 5 Test schedule and sampling plan for lot-by-lot tests 23 Table 6 Test schedule for safety tests only (1 of 2) 24 Table 7 Test schedule for safety and performance tests qualification approval Assessment level DZ 26 Table 8 Assessment level 32 Table 9 Creepage distances and

38、clearances 33 Table 10 Voltage proof . 35 Table 11 Insulation resistance Safety tests only 36 Table 12 Insulation resistance Safety and performance tests 37 Table 13 Resistance to soldering heat Requirements 38 Table 14 Climatic sequence Requirements 41 Table 15 Damp heat, steady state Requirements

39、42 Table 16 Endurance Requirements . 46 Table 17 Charge and discharge Requirements 47 Table A.1 Values of CX, CT, RP, RS, Cp. 52 Table A.2 Values and tolerances of CX, tr, td. 53 Table F.1 Test schedule and sampling plan for safety test of surface mount capacitors . 60 6 60384-14 IEC:2013 INTERNATIO

40、NAL ELECTROTECHNICAL COMMISSION _ FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT Part 14: Sectional specification Fixed capacitors for electromagnetic interference suppression and connection to the supply mains FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organiza

41、tion for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC

42、 publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with

43、 may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agr

44、eement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC

45、 Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are use

46、d or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the co

47、rresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible f

48、or any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees

49、and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited i