IEC 60384-13-1-2006 Fixed capacitors for use in electronic equipment - Part 13 Sectional specification - Fixed polypropylene film dielectric metal foil d.c capa.pdf

《IEC 60384-13-1-2006 Fixed capacitors for use in electronic equipment - Part 13 Sectional specification - Fixed polypropylene film dielectric metal foil d.c capa.pdf》由会员分享，可在线阅读，更多相关《IEC 60384-13-1-2006 Fixed capacitors for use in electronic equipment - Part 13 Sectional specification - Fixed polypropylene film dielectric metal foil d.c capa.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、 INTERNATIONAL STANDARD IEC 60384-13-1QC 301801 Second edition 2006-01Fixed capacitors for use in electronic equipment Part 13-1: Blank detail specification Fixed polypropylene film dielectric metal foil d.c. capacitors Assessment level E Reference number IEC 60384-13-1:2006(E) Publication numbering

2、 As from 1 January 1997 all IEC publications are issued with a designation in the 60000 series. For example, IEC 34-1 is now referred to as IEC 60034-1. Consolidated editions The IEC is now publishing consolidated versions of its publications. For example, edition numbers 1.0, 1.1 and 1.2 refer, res

3、pectively, to the base publication, the base publication incorporating amendment 1 and the base publication incorporating amendments 1 and 2. Further information on IEC publications The technical content of IEC publications is kept under constant review by the IEC, thus ensuring that the content ref

4、lects current technology. Information relating to this publication, including its validity, is available in the IEC Catalogue of publications (see below) in addition to new editions, amendments and corrigenda. Information on the subjects under consideration and work in progress undertaken by the tec

5、hnical committee which has prepared this publication, as well as the list of publications issued, is also available from the following: IEC Web Site (www.iec.ch) Catalogue of IEC publications The on-line catalogue on the IEC web site (www.iec.ch/searchpub) enables you to search by a variety of crite

6、ria including text searches, technical committees and date of publication. On-line information is also available on recently issued publications, withdrawn and replaced publications, as well as corrigenda. IEC Just Published This summary of recently issued publications (www.iec.ch/online_news/ justp

7、ub) is also available by email. Please contact the Customer Service Centre (see below) for further information. Customer Service Centre If you have any questions regarding this publication or need further assistance, please contact the Customer Service Centre: Email: custserviec.ch Tel: +41 22 919 0

8、2 11 Fax: +41 22 919 03 00 INTERNATIONAL STANDARD IEC 60384-13-1QC 301801 Second edition 2006-01Fixed capacitors for use in electronic equipment Part 13-1: Blank detail specification Fixed polypropylene film dielectric metal foil d.c. capacitors Assessment level E IEC 2006 Copyright - all rights res

9、erved No part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. International Electrotechnical Commission, 3, rue de Varemb, PO Box 131, CH-1211 Geneva 20, S

10、witzerland Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmailiec.ch Web: www.iec.ch M For price, see current catalogue PRICE CODE Commission Electrotechnique Internationale International Electrotechnical Commission 2 60384-13-1 IEC:2006(E) INTERNATIONAL ELECTROTECHNICAL COMMISSION

11、_ FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT Part 13-1: Blank detail specification Fixed polypropylene film dielectric metal foil d.c. capacitors Assessment level E FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all na

12、tional electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Techni

13、cal Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work.

14、 International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2)

15、The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommenda

16、tions for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end

17、 user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publicat

18、ion shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7)

19、No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for cost

20、s (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct applica

21、tion of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60384-13-1 has been prepared by IEC te

22、chnical committee 40: Capacitors and resistors for electronic equipment. This second edition cancels and replaces the first edition published in 1991 and constitutes a minor revisions related to tables, figures and references. The text of this standard is based on the following documents: FDIS Repor

23、t on voting 40/1621/FDIS 40/1644/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. 60384-13-1 IEC:2006(E) 3 The QC number that appears on the front cover of this publication is the specification number in the IEC Q

24、uality Assessment System for Electronic Components (IECQ). This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. IEC 60384 consists of the following parts, under the general title Fixed capacitors for use in electronic equipment: Part 1: Generic specification Part 2: S

25、ectional specification: Fixed metallized polyethylene-terephthalate film dielectric d.c. capacitors Part 3: Sectional specification: Fixed tantalum chip capacitors Part 4: Sectional specification: Aluminium electrolytic capacitors with solid and non-solid electrolyte Part 5: Sectional specification:

26、 Fixed mica dielectric d.c. capacitors with a rated voltage not exceeding 3000 V Selection of methods of test and general requirements Part 6: Sectional specification: Fixed metallized polycarbonate film dielectric d.c. capacitors Part 8: Sectional specification: Fixed capacitors of ceramic dielectr

27、ic, Class 1 Part 9: Sectional specification: Fixed capacitors of ceramic dielectric, Class 2 Part 11: Sectional specification: Fixed polyethylene-terephthalate film dielectric metal foil d.c. capacitors Part 12: Sectional specification: Fixed polycarbonate film dielectric metal foil d.c. capacitors

28、Part 13: Sectional specification: Fixed polypropylene film dielectric metal foil d.c. capacitors Part 14: Sectional specification: Fixed capacitors for electromagnetic interference suppression and connection to the supply mains Part 15: Sectional specification: Fixed tantalum capacitors with non-sol

29、id or solid electrolyte Part 16: Sectional specification: Fixed metallized polypropylene film dielectric d.c. capacitors Part 17: Sectional specification: Fixed metallized polypropylene film dielectric a.c. and pulse capacitors Part 18: Sectional specification: Fixed aluminium electrolytic chip capa

30、citors with solid electrolyte Part 19: Sectional specification: Fixed metallized polyethylene-terephthalate film dielectric chip d.c. capacitors Part 20: Sectional specification: Fixed metallized polyphenylene sulfide film dielectric chip d.c. capacitors Part 21: Sectional specification: Fixed surfa

31、ce mount multilayer capacitors of ceramic dielectric, Class 1 Part 22: Sectional specification: Fixed surface mount multilayer capacitors of ceramic dielectric, Class 2 Part 23: Sectional specification: Fixed surface mount metallized polyethylene naphthalate film dielectric d.c. capacitors 4 60384-1

32、3-1 IEC:2006(E) Part 24: Sectional specification Surface mount fixed tantalum electrolytic capacitors with conductive polymer solid electrolyte 1Part 25: Sectional specification Surface mount fixed aluminium electrolytic capacitors with conductive polymer solid electrolyte 1All sectional specificati

33、ons mentioned above do have one or more blank detail specifications being a supplementary document, containing requirements for style, layout and minimum content of detail specifications. The committee has decided that the contents of this publication will remain unchanged until the maintenance resu

34、lt date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed; withdrawn; replaced by a revised edition, or amended. A bilingual version of this publication may be issued at a later date. 1To be

35、published. 60384-13-1 IEC:2006(E) 5 FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT Part 13-1: Blank detail specification Fixed polypropylene film dielectric metal foil d.c. capacitors Assessment level E Blank detail specification A blank detail specification is a supplementary document to the sect

36、ional specification and contains requirements for style and layout and minimum content of detail specifications. Detail specifications not complying with these requirements may not be considered as being in accordance with IEC specifications nor shall they so be described. In the preparation of deta

37、il specifications the content of 1.4 of the sectional specification shall be taken into account. The numbers between brackets on the first page correspond to the following information which shall be inserted in the position indicated. Identification of the detail specification (1) The “International

38、 Electrotechnical Commission“ or the National Standards Organization under whose authority the detail specification is drafted. (2) The IEC or National Standards number of the detail specification, date of issue and any further information required by the national system. (3) The number and issue nu

39、mber of the IEC or national generic specification. (4) The IEC number of the blank detail specification. Identification of the capacitor (5) A short description of the type of capacitor. (6) Information on typical construction (when applicable). When the capacitor is not designed for use in printed-

40、board applications, this shall be clearly stated in the detail specification in this position. (7) Outline drawing with main dimensions which are of importance for interchangeability and/or reference to the national or international documents for outlines. Alternatively, this drawing may be given in

41、 an annex to the detail specification. (8) Application or group of applications covered and/or assessment level. The assessment level(s) to be used in a detail specification shall be selected from the sectional specification, 3.5.4. This implies that one blank detail specification may be used in com

42、bination with several assessment levels, provided the grouping of the tests does not change. (9) Reference data on the most important properties, to allow comparison between the various capacitor types. 6 60384-13-1 IEC:2006(E) ( 1 ) IEC 60384-13-1-XXX ( 2 ) QC 301801-XXX IEC 60384-13-1 (4) QC 30180

43、1 ELECTRONIC COMPONENTS OF ASSESSED QUALITY IN ACCORDANCE WITH: ( 3 ) FIXED POLYPROPYLENE (5) FILM DIELECTRIC METAL FOIL DC CAPACITORS ( 6 ) Outline drawing: (see Table 1) (.angle projection) ( 7 ) (Other shapes are permitted within the dimensions given.) Assessment level(s): E (8) Stability class:

44、Information on the availability of components qualified to this detail specification is given in IEC QC 001005 (9) 1 General data 1.1 Recommended method(s) of mounting See IEC 60384-13, 1.4.2. 1.2 Dimensions Table 1 Case size reference and dimensions Dimensions (in mm) Case size reference L H d . Wh

45、en there is no case size reference, Table 1 may be omitted and the dimensions shall be given in Table 2, which then becomes Table 1. The dimensions shall be given as maximum dimensions or as nominal dimensions with a tolerance. 60384-13-1 IEC:2006(E) 7 1.3 Ratings and characteristics Capacitance ran

46、ge (see Table 2) Tolerance on rated capacitance Rated voltage (see Table 2) Category voltage (if applicable) (see Table 2) Climatic category Rated temperature Maximum a.c. voltage (if applicable) Tangent of loss angle Insulation resistance Table 2 Values of capacitance and of voltage related to case

47、 sizes Rated voltage Category voltage aCase size Case size Case size Case size Rated capacitance (in pF, nF and/or F) aIf different from the rated voltage. 1.4 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only t

48、he edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60410, Sampling plans and procedures for inspection by attributes IEC 60384-1, Fixed capacitors for use in electronic equipment Part 1: Generic specification IEC 60

49、384-13, Fixed capacitors for use in electronic equipment Part 13: Sectional Specification: Fixed polypropylene film dielectric metal foil d.c. capacitors 1.5 Marking The marking of the capacitor and the package shall be in accordance with the requirements of IEC 60384-13, 1.6. The details of the marking of the component and package shall be given in full in the detail specification. 1.6 Ordering information Orders for ca