IEC TS 62642-7-2011 Alarm systems - Intrusion and hold-up systems - Part 7 Application guidelines《报警系统.入侵和拦截系统.第7部分 应用指南》.pdf

《IEC TS 62642-7-2011 Alarm systems - Intrusion and hold-up systems - Part 7 Application guidelines《报警系统.入侵和拦截系统.第7部分 应用指南》.pdf》由会员分享，可在线阅读，更多相关《IEC TS 62642-7-2011 Alarm systems - Intrusion and hold-up systems - Part 7 Application guidelines《报警系统.入侵和拦截系统.第7部分 应用指南》.pdf（58页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC/TS 62642-7 Edition 1.0 2011-02 TECHNICAL SPECIFICATION Alarm systems Intrusion and hold-up systems Part 7: Application guidelines IEC/TS 62642-7:2011(E) THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2011 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of th

2、is publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or

3、have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise

4、sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplment

5、aires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About IEC publications The technical content of IEC publications is k

6、ept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, techn

7、ical committee,). It also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available on-line and also by email. Elect

8、ropedia: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary online. Customer S

9、ervice Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC/TS 62642-7 Edition 1.0 2011-02 TECHNICAL SPEC

10、IFICATION Alarm systems Intrusion and hold-up systems Part 7: Application guidelines INTERNATIONAL ELECTROTECHNICAL COMMISSION XA ICS 13.320 PRICE CODE ISBN 978-2-88912-348-3 Registered trademark of the International Electrotechnical Commission 2 TS 62642-7 IEC:2011(E) CONTENTS FOREWORD . 4 INTRODUC

11、TION . 6 1 Scope . 8 2 Normative references . 8 3 Terms, definitions and abbreviations 8 3.1 Terms and definitions 8 3.2 Abbreviations 13 4 Security grade of I any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and no

12、n- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements

13、of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are

14、 accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote inter

15、national uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in t

16、he latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All user

17、s should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or othe

18、r damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. U

19、se of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent

20、 rights. The main task of IEC technical committees is to prepare International Standards. In exceptional circumstances, a technical committee may propose the publication of a technical specification when the required support cannot be obtained for the publication of an International Standard, despit

21、e repeated efforts, or the subject is still under technical development or where, for any other reason, there is the future but no immediate possibility of an agreement on an International Standard. Technical specifications are subject to review within three years of publication to decide whether th

22、ey can be transformed into International Standards. IEC 62642-7, which is a technical specification, has been prepared by IEC technical committee 79: Alarm and electronic security systems. TS 62642-7 IEC:2011(E) 5 This standard is based on EN/TS 50131-7 (2010). The text of this technical specificati

23、on is based on the following documents: Enquiry draft Report on voting 79/315/DTS 79/332/RVC Full information on the voting for the approval of this technical specification can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO

24、/IEC Directives, Part 2. A list of all parts of the IEC 62642 series can be found, under the general title: Alarm systems Intrusion and hold-up systems, on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the

25、 IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be be transformed into an International standard, reconfirmed, withdrawn, replaced by a revised edition, or amended. A bilingual version of this publication may be issued a

26、t a later date. 6 TS 62642-7 IEC:2011(E) INTRODUCTION This part 7 of the IEC 62642 series of standards gives requirements for intrusion and hold-up alarm systems. The other parts of this series of standards are as follows: Part 1 System requirements Part 2-2 Intrusion detectors Passive infrared dete

27、ctors Part 2-3 Intrusion detectors Microwave detectors Part 2-4 Intrusion detectors Combined passive infrared / microwave detectors Part 2-5 Intrusion detectors Combined passive infrared / ultrasonic detectors Part 2-6 Intrusion detectors Opening contacts (magnetic) Part 2-71 Intrusion detectors Gla

28、ss break detectors Acoustic Part 2-72 Intrusion detectors Glass break detectors Passive Part 2-73 Intrusion detectors Glass break detectors Active Part 3 Control and indicating equipment Part 4 Warning devices Part 5-3 Interconnections Requirements for equipment using radio frequency techniques Part

29、 6 Power supplies Part 7 Application guidelines Part 8Security fog devices/systems In order to insure the consistency of the whole IEC 62642 series, the terminology is defined at one place that is the master document IEC 62642-1 that gives general requirements concerning the intrusion system. Except

30、ion is made for specific terms to installation and where repetition is deemed essential for the clarity of this document. A number of requirements are contained in this standard for which a formal test procedure can only be written by defining (and hence restricting) the technology by which the requ

31、irement is achieved. Accordingly, it has been recognised that such functions can be tested only by agreement between installers and test house, according to documented information relating to how the required functionality has been achieved. These application guidelines are intended to provide advic

32、e relating to the design, installation, operation and maintenance of Intruder and Hold-up Alarm Systems (I a brief explanation of each section is shown below. a) Clause 7 System design TS 62642-7 IEC:2011(E) 7 This clause is intended to assist those responsible for designing I&HAS to design I&HAS su

33、itable for the premises to be supervised in relation to the perceived risk(s). The design of I&HAS will depend on many factors, all of which will influence more or less the design of I&HAS. Consideration of these factors will result in a system design proposal for an I&HAS with the appropriate exten

34、t, security grade and environmental class. b) Clause 8 Installation planning This clause is intended to help those responsible for installing I&HAS by highlighting issues which should be considered prior to commencing the installation of the I&HAS. c) Clause 9 System installation In this clause, gui

35、dance is given with regard to issues arising during the installation of I&HAS. This clause is intended to ensure I&HAS is correctly installed as specified at the design stage. d) Clause 10 Inspection, functional testing and commissioning In this clause, guidance is given on issues arising after I&HA

36、S has been installed. The clause is intended to ensure I&HAS has been installed as specified and also provides the level of performance intended at the design stage. Guidance is also provided with regard to the proper commissioning and handing over of the system to the user and to the documents, rec

37、ords and operating instructions which should be provided. e) Clause 11 Documentation and records This clause describes the documentation which should be provided to the client on completion of I&HAS. The documents are intended to provide a history of modifications to I&HAS, based on the as-fitted do

38、cument, prepared when I&HAS installation was completed. The records are intended to chronicle any corrective action carried out following unwanted alarm conditions and details of any repairs or modifications to I&HAS. The record should also include details of temporary fault conditions. f) Clause 12

39、 Operation of I&HAS This clause describes the responsibility of the client or user of I&HAS to properly maintain I&HAS and to ensure it is operated correctly. g) Clause 13 Maintenance and repair of I&HAS This clause describes how I&HAS should be maintained and repaired to ensure I&HAS continues to provide the level of performance intended at the design stage.