IEC 62305-4-2010 Protection against lightning - Part 4 Electrical and electronic systems within structures《雷电防护.第4部分 建筑物中电气和电子系统》.pdf

《IEC 62305-4-2010 Protection against lightning - Part 4 Electrical and electronic systems within structures《雷电防护.第4部分 建筑物中电气和电子系统》.pdf》由会员分享，可在线阅读，更多相关《IEC 62305-4-2010 Protection against lightning - Part 4 Electrical and electronic systems within structures《雷电防护.第4部分 建筑物中电气和电子系统》.pdf（182页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 62305-4 Edition 2.0 2010-12 INTERNATIONAL STANDARD NORME INTERNATIONALE Protection against lightning Part 4: Electrical and electronic systems within structures Protection contre la foudre Partie 4: Rseaux de puissance et de communication dans les structures IEC62305-4:2010 THIS PUBLICATION IS

2、COPYRIGHT PROTECTED Copyright 2010 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from eithe

3、r IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droit

4、s de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI

5、du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue

6、de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About

7、IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Useful links: IEC publications search - www.iec.ch/searchpub The advanced search enables you

8、 to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all ne

9、w publications released. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms in additional language

10、s. Also known as the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. A propos de la CEI La Commission Ele

11、ctrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu

12、. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub La recherche avance vous permet de trouver des publications CEI en utilisant diffrents critres (numro de rfrence, texte

13、, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications de la CEI. Just Published dtaille les nouvelles publications parues. Disponible en ligne et au

14、ssi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement ap

15、pel Vocabulaire Electrotechnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 62305-4 Edition 2.0 2010-12 INTERNATIONAL STANDARD NORME INTERNATIONALE

16、Protection against lightning Part 4: Electrical and electronic systems within structures Protection contre la foudre Partie 4: Rseaux de puissance et de communication dans les structures INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE XC ICS 29.020; 91.120.40 PRI

17、CE CODE CODE PRIX ISBN 978-2-83220-130-5 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous

18、 avez obtenu cette publication via un distributeur agr. 2 62305-4 IEC:2010 CONTENTS FOREWORD . 5 INTRODUCTION . 7 1 Scope . 9 2 Normative references . 9 3 Terms and definitions . 10 4 Design and installation of SPM . 13 4.1 General . 13 4.2 Design of SPM 16 4.3 Lightning protection zones (LPZ) . 17

19、4.4 Basic SPM 20 5 Earthing and bonding . 21 5.1 General . 21 5.2 Earth-termination system . 22 5.3 Bonding network 24 5.4 Bonding bars . 28 5.5 Bonding at the boundary of an LPZ . 29 5.6 Material and dimensions of bonding components . 29 6 Magnetic shielding and line routing . 30 6.1 General . 30 6

20、.2 Spatial shielding 30 6.3 Shielding of internal lines 30 6.4 Routing of internal lines . 30 6.5 Shielding of external lines . 31 6.6 Material and dimensions of magnetic shields . 31 7 Coordinated SPD system 31 8 Isolating interfaces . 32 9 SPM management 32 9.1 General . 32 9.2 SPM management plan

21、 . 32 9.3 Inspection of SPM . 33 9.3.1 General . 33 9.3.2 Inspection procedure . 34 9.3.3 Inspection documentation 34 9.4 Maintenance 35 Annex A (informative) Basis of electromagnetic environment evaluation in an LPZ 36 Annex B (informative) Implementation of SPM for an existing structure 60 Annex C

22、 (informative) Selection and installation of a coordinated SPD system 76 Annex D (informative) Factors to be considered in the selection of SPDs . 82 Bibliography 87 Figure 1 General principle for the division into different LPZ 13 Figure 2 Examples of possible SPM (LEMP protection measures) 15 Figu

23、re 3 Examples for interconnected LPZ . 19 Figure 4 Examples for extended lightning protection zones 20 62305-4 IEC:2010 3 Figure 5 Example of a three-dimensional earthing system consisting of the bonding network interconnected with the earth-termination system 22 Figure 6 Meshed earth-termination sy

24、stem of a plant . 23 Figure 7 Utilization of reinforcing rods of a structure for equipotential bonding . 25 Figure 8 Equipotential bonding in a structure with steel reinforcement . 26 Figure 9 Integration of conductive parts of internal systems into the bonding network 27 Figure 10 Combinations of i

25、ntegration methods of conductive parts of internal systems into the bonding network . 28 Figure A.1 LEMP situation due to lightning strike . 37 Figure A.2 Simulation of the rise of magnetic field by damped oscillations . 40 Figure A.3 Large volume shield built by metal reinforcement and metal frames

26、 41 Figure A.4 Volume for electrical and electronic systems inside an inner LPZ n . 42 Figure A.5 Reducing induction effects by line routing and shielding measures . 43 Figure A.6 Example of SPM for an office building . 45 Figure A.7 Evaluation of the magnetic field values in case of a direct lightn

27、ing strike . 46 Figure A.8 Evaluation of the magnetic field values in case of a nearby lightning strike . 48 Figure A.9 Distance sadepending on rolling sphere radius and structure dimensions 51 Figure A.10 Types of grid-like large volume shields . 52 Figure A.11 Magnetic field strengthH1/MAXinside a

28、 grid-like shield type 1 . 53 Figure A.12 Magnetic field strengthH1/MAXinside a grid-like shield type 1 according to mesh width . 54 Figure A.13 Low-level test to evaluate the magnetic field inside a shielded structure . 55 Figure A.14 Voltages and currents induced into a loop formed by lines 56 Fig

29、ure B.1 SPM design steps for an existing structure . 63 Figure B.2 Possibilities to establish LPZ in existing structures . 67 Figure B.3 Reduction of loop area using shielded cables close to a metal plate . 69 Figure B.4 Example of a metal plate for additional shielding 70 Figure B.5 Protection of a

30、erials and other external equipment . 71 Figure B.6 Inherent shielding provided by bonded ladders and pipes . 72 Figure B.7 Ideal positions for lines on a mast (cross-section of steel lattice mast) 72 Figure B.8 Upgrading of the SPM in existing structures 74 Figure C.1 Surge voltage between live con

31、ductor and bonding bar 79 Figure D.1 Installation example of test class I, class II and class III SPDs . 83 Figure D.2 Basic example for different sources of damage to a structure and lightning current distribution within a system . 84 Figure D.3 Basic example of balanced current distribution . 85 T

32、able 1 Minimum cross-sections for bonding components 30 Table 2 SPM management plan for new buildings and for extensive changes in construction or use of buildings 33 Table A.1 Parameters relevant to source of harm and equipment . 38 Table A.2 Examples for I0MAX = 100 kA and wm= 2 m . 48 Table A.3 M

33、agnetic attenuation of grid-like spatial shields for a plane wave . 49 Table A.4 Rolling sphere radius corresponding to maximum lightning current 51 4 62305-4 IEC:2010 Table A.5 Examples for I0/MAX= 100 kA and wm= 2 m corresponding to SF = 12,6 dB . 51 Table B.1 Structural characteristics and surrou

34、ndings 60 Table B.2 Installation characteristics 61 Table B.3 Equipment characteristics 61 Table B.4 Other questions to be considered for the protection concept 61 Table D.1 Preferred values of Iimp. 82 62305-4 IEC:2010 5 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ PROTECTION AGAINST LIGHTNING Part

35、4: Electrical and electronic systems within structures FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-opera

36、tion on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as

37、“IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this prepa

38、ration. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international conse

39、nsus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts a

40、re made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications t

41、ransparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independe

42、nt certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liabi

43、lity shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (inclu

44、ding legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of

45、this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 62305-4 has been prepared by IEC technical com

46、mittee 81: Lightning protection. This second edition cancels and replaces the first edition, published in 2006, and constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: 1) Isolating interfaces capable of reducing co

47、nducted surges on lines entering the structure are introduced. 2) Minimum cross-sections for bonding components are slightly modified. 3) First negative impulse current is introduced for calculation purposes as electromagnetic source of harm to the internal systems. 4) Selection of SPD with regard t

48、o voltage protection level is improved to take into account oscillation and induction phenomena in the circuit downstream of SPD. 5) Annex C dealing with SPD coordination is withdrawn and referred back to SC 37A. 6 62305-4 IEC:2010 6) A new informative Annex D is introduced giving information on fac

49、tors to be considered in the selection of SPDs. This bilingual version (2012-06) corresponds to the monolingual English version, published in 2010-12. The text of this standard is based on the following documents: FDIS Report on voting 81/373/FDIS 81/383/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in th