IEC 62272-2-2007 Digital radio mondiale (DRM) - Part 2 Digital radio in the bands below 30 MHz - Methods of measurement for DRM transmitters《全球数字无线广播(DRM).第2部分 波段小于30MHz的无线广播.DRM发射机的测量方法》.pdf

《IEC 62272-2-2007 Digital radio mondiale (DRM) - Part 2 Digital radio in the bands below 30 MHz - Methods of measurement for DRM transmitters《全球数字无线广播(DRM).第2部分 波段小于30MHz的无线广播.DRM发射机的测量方法》.pdf》由会员分享，可在线阅读，更多相关《IEC 62272-2-2007 Digital radio mondiale (DRM) - Part 2 Digital radio in the bands below 30 MHz - Methods of measurement for DRM transmitters《全球数字无线广播(DRM).第2部分 波段小于30MHz的无线广播.DRM发射机的测量方法》.pdf（44页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 62272-2 Edition 1.0 2007-03 INTERNATIONAL STANDARD NORME INTERNATIONALE Digital radio mondiale (DRM) Part 2: Digital radio in the bands below 30 MHz Methods of measurement for DRM transmitters Digital radio mondiale (DRM) Partie 2: Radiodiffusion numrique sur des bandes infrieures 30 MHz Mthode

2、s de mesure applicables aux metteurs DRM IEC 62272-2:2007 colour inside THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2007 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic o

3、r mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact

4、the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris

5、la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit nat

6、ional de la CEI de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publi

7、shes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published.

8、Useful links: IEC publications search - www.iec.ch/searchpub The advanced search enables you to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec

9、.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 0

10、00 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance,

11、 please contact the Customer Service Centre: csciec.ch. A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A prop

12、os des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub La recherche avance vous pe

13、rmet de trouver des publications CEI en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications de

14、 la CEI. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais

15、et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-n

16、ous: csciec.ch. IEC 62272-2 Edition 1.0 2007-03 INTERNATIONAL STANDARD NORME INTERNATIONALE Digital radio mondiale (DRM) Part 2: Digital radio in the bands below 30 MHz Methods of measurement for DRM transmitters Digital radio mondiale (DRM) Partie 2: Radiodiffusion numrique sur des bandes infrieure

17、s 30 MHz Mthodes de mesure applicables aux metteurs DRM INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE R ICS 33.060.20 PRICE CODE CODE PRIX ISBN 978-2-88912-904-1 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission

18、 Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. colour inside 2 62272-2 IEC:2007 CONTENTS FOREWORD . 3 1 Scope . 5 2 Normative refer

19、ences 5 3 Terms, definitions and abbreviations . 6 3.1 Terms and definitions 6 3.2 Abbreviations . 6 4 General conditions of operation . 7 5 General conditions of measurement 7 5.1 Input and output measurement arrangements 7 5.2 Temperature and humidity . 8 5.3 Conditions for primary power supply .

20、8 5.4 Output power . 8 6 General characteristics . 8 6.1 Output power . 8 6.2 Frequency . 9 7 Transmission performance characteristics 11 7.1 Spurious emissions 11 7.2 Out-of-band emissions (spectrum mask) 12 7.3 Modulation error ratio (MER) 13 7.4 Bit error ratio (BER) . 13 8 Protection against atm

21、ospheric discharge . 14 9 Acoustic noise 14 10 Safety . 15 Annex A (informative) Measuring arrangements 16 Annex B (informative) Out-of-band emission limits for DRM transmitters . 18 Annex C (informative) Additional measuring details 20 Figure 1 Spectrum occupancy for 9 kHz channels . 10 Figure 2 Sp

22、ectrum occupancy for 10 kHz channels . 10 Figure 3 PRBS generator . 14 Figure A.1 Arrangement A 16 Figure A.2 Arrangement B 16 Figure A.3 Arrangement C 17 Figure A.4 Arrangement D 17 Figure B.1 Out-of-band emission limits (upper half only of a symmetrical spectrum mask shown) . 18 Table B.1 Out-of-b

23、and emission limits 18 62272-2 IEC:2007 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ DIGITAL RADIO MONDIALE (DRM) Part 2: Digital radio in the bands below 30 MHz Methods of measurement for DRM transmitters FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization f

24、or standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publi

25、shes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may p

26、articipate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreemen

27、t between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publ

28、ications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or

29、for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresp

30、onding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the lat

31、est edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whe

32、ther direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is i

33、ndispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 62

34、272-2 has been prepared by IEC technical committee 103: Transmitting equipment for radiocommunication. This bilingual version (2012-05) corresponds to the monolingual English version, published in 2007-03. The text of this standard is based on the following documents: FDIS Report on voting 103/64/FD

35、IS 103/66/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. 4 62272-2 IEC:2007 The committee has decided that the contents of thi

36、s publication will remain unchanged until the maintenance result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed; withdrawn; replaced by a revised edition, or amended. IMPORTANT The co

37、lour inside logo on the cover page of this publication indicates that it contains colours which are considered to be useful for the correct understanding of its contents. Users should therefore print this document using a colour printer. 62272-2 IEC:2007 5 DIGITAL RADIO MONDIALE (DRM) Part 2: Digita

38、l radio in the bands below 30 MHz Methods of measurement for DRM transmitters 1 Scope This part of IEC 62272 describes the methods of measurement to assess the performance characteristics of digital modulated radio transmitters in the bands below 30 MHz for sound and/or data broadcasting in the LF,

39、MF and HF bands, and to facilitate the comparison of measurements which are carried out by different personnel. It contains details of specially selected methods for determining the most important performance parameters of digital radio transmitters. The measurement methods described apply to a limi

40、ted number of performance parameters, i.e. those which can give rise to ambiguous interpretation due to the use of different methods and conditions. They are neither restrictive nor mandatory: measurements can be chosen for each particular case. The measurement methods described in this standard are

41、 intended to be used for type approval tests, quality control tests or acceptance test measurements in factories and on site. Fewer or additional measurements may be carried out by agreement between customer and supplier. Any additional test should comply with standards which have been established b

42、y other study groups, subcommittees of the IEC or other international or suitably accredited organizations. This standard does not specify limiting values for acceptable performance as these are usually given in the equipment specification or in requirements laid down by the responsible regulation b

43、odies. However, some values are quoted, where appropriate, for guidance in the presentation of the results. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references,

44、the latest edition of the referenced document (including any amendments) applies. IEC 60244-1, Methods of measurement for radio transmitters Part 1: General characteristics for broadcast transmitters IEC 60244-15, Methods of measurement for radio transmitters Part 15: Amplitude-modulated transmitter

45、s for sound broadcasting IEC 60215, Safety requirements for radio transmitting equipment ITU Radio Regulations ITU-R Recommendation V.663, Use of certain terms linked with physical quantities 6 62272-2 IEC:2007 3 Terms, definitions and abbreviations 3.1 Terms and definitions For the purposes of this

46、 document, the following terms and definitions apply. 3.1.1 DRM standard digital modulation standard for frequencies in the bands below 30 MHz for the purposes of audio and data broadcasting 3.1.2 DRM transmitters sound broadcasting transmitters operating in the bands below 30 MHz and incorporating

47、digital modulation in accordance with IEC 62272-1 13.1.3 power definitions nominal output power is the continuous DRM mean power for which the transmitter is designed maximum output power is the maximum possible continuous DRM mean power which the transmitter can deliver. The maximum output power mi

48、ght be concordant with the nominal output power minimum output power is the minimum possible continuous DRM mean power for which the transmitter is designed 3.1.4 necessary bandwidth for a given class of emission, the width of a frequency band which is just sufficient to ensure the transmission of i

49、nformation at the rate and with the quality required under specified conditions (ITU definition) For the practical purposes of this standard, the necessary bandwidth for a DRM signal can be considered to be the same as the allocated channel bandwidth, for example, 10 Hz for a standard HF channel. 3.2 Abbreviations BER Bit Error Ratio BS Broadcasting Service DRM Digital Radio Mondiale FAC Fast Access Channel H