IEC 62271-205-2008 High-voltage switchgear and controlgear - Part 205 Compact switchgear assemblies for rated voltages above 52 kV《高压开关装置和控制装置.第205部分 额定电压52kV以上用紧凑开关控制组件》.pdf

《IEC 62271-205-2008 High-voltage switchgear and controlgear - Part 205 Compact switchgear assemblies for rated voltages above 52 kV《高压开关装置和控制装置.第205部分 额定电压52kV以上用紧凑开关控制组件》.pdf》由会员分享，可在线阅读，更多相关《IEC 62271-205-2008 High-voltage switchgear and controlgear - Part 205 Compact switchgear assemblies for rated voltages above 52 kV《高压开关装置和控制装置.第205部分 额定电压52kV以上用紧凑开关控制组件》.pdf（52页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 62271-205 Edition 1.0 2008-01 INTERNATIONAL STANDARD NORME INTERNATIONALE High-voltage switchgear and controlgear Part 205: Compact switchgear assemblies for rated voltages above 52 kV Appareillage haute tension Partie 205: Ensembles dappareillages compacts de tensions assignes suprieures 52 kV

2、 IEC 62271-205:2008 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2008 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm,

3、without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National

4、Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit d

5、e la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Centr

6、al Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologie

7、s. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enabl

8、es you to search by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month a

9、ll new publications released. Available on-line and also by email. Electropedia: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in additional languages. Also k

10、nown as the International Electrotechnical Vocabulary online. Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11

11、 Fax: +41 22 919 03 00 A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le conten

12、u technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue en-ligne de la CEI vous permet deffectuer

13、 des recherches en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Il donne aussi des informations sur les projets et les publications retires ou remplaces. Just Published CEI: www.iec.ch/online_news/justpub Restez inform sur les nouvelles publications de la CEI. Just Published

14、 dtaille deux fois par mois les nouvelles publications parues. Disponible en-ligne et aussi par email. Electropedia: www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 20 000 termes et dfinitions en anglais et en franais, ainsi qu

15、e les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International en ligne. Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le

16、 FAQ du Service clients ou contactez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC 62271-205 Edition 1.0 2008-01 INTERNATIONAL STANDARD NORME INTERNATIONALE High-voltage switchgear and controlgear Part 205: Compact switchgear assemblies for rated voltages above 52 kV Apparei

17、llage haute tension Partie 205: Ensembles dappareillages compacts de tensions assignes suprieures 52 kV INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE T ICS 29.130.10; 29.130.99 PRICE CODE CODE PRIX ISBN 2-8318-9511-1 2 62271-205 IEC:2008 CONTENTS FOREWORD.4 1 G

18、eneral 6 1.1 Scope6 1.2 Normative references 7 2 Normal and special service conditions8 3 Terms and definitions .8 3.1 General terms .8 3.2 Compact switchgear assembly 9 4 Rating 9 4.1 Rated voltage (U r ) .9 4.2 Rated insulation level 10 4.3 Rated frequency (f r ).10 4.4 Rated normal current (I r )

19、 and temperature rise 10 4.5 Rated short-time withstand current (I k ) 10 4.6 Rated peak withstand current (I p ) 10 4.7 Rated duration of short circuit (t k )10 4.8 Rated supply voltage of closing and opening devices and of auxiliary and control circuits (U a )10 4.9 Rated supply frequency of closi

20、ng and opening devices and of auxiliary circuits 10 5 Design and construction .11 5.3 Earthing of switchgear and controlgear.11 5.101 Earthing of compact switchgear assemblies and their controlgear.11 5.102 Pressure relief devices .11 5.10 Nameplates 11 5.12 Position indication 11 5.103 Locking devi

21、ces for maintenance operation 11 5.104 Movement of pressurized devices.12 5.105 Isolating distance for maintenance12 6 Type tests 12 6.1 General 12 6.2 Dielectric tests13 6.3 Radio interference voltage (r.i.v.) test.13 6.4 Measurement of the resistance of circuits.14 6.5 Temperature-rise tests14 6.6

22、 Short-time withstand current and peak withstand current tests14 6.101 Mechanical and environmental tests .15 7 Routine tests 17 7.1 Dielectric test on the main circuit 17 7.2 Tests on auxiliary and control circuits .17 7.3 Measurement of the resistance of the main circuit 17 7.101 Functional tests

23、on auxiliary and control circuits .17 8 Guide to the selection of switchgear and controlgear17 8.101 Guide to the selection of compact switchgear assemblies.17 9 Information to be given with enquiries, tenders and orders .18 62271-205 IEC:2008 3 10 Transport, storage, installation, operation and mai

24、ntenance .18 10.1 Conditions during transport, storage and installation .18 10.2 Installation 18 10.3 Operation 18 10.4 Maintenance18 11 Safety.18 Annex AA (informative) Explanations of compact switchgear assemblies .19 Bibliography23 Figure AA.1 Example for type 1 .21 Figure AA.2 Example for type 2

25、 .21 Figure AA.3 Example for type 3 .22 Figure AA.4 Example for type 3 .22 Table 101 Type tests on the compact switchgear assembly .12 4 62271-205 IEC:2008 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR Part 205: Compact switchgear assemblies for rated voltages a

26、bove 52 kV FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardiza

27、tion in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is

28、entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the I

29、nternational Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects si

30、nce each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical conten

31、t of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible

32、 in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment

33、 declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC Na

34、tional Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention

35、 is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC sh

36、all not be held responsible for identifying any or all such patent rights. International Standard IEC 62271-205 has been prepared by subcommittee 17C: High-voltage switchgear and controlgear assemblies, of IEC technical committee 17: Switchgear and controlgear. This standard should be read in conjun

37、ction with IEC 62271-1, first edition, to which it refers and which is applicable, unless otherwise specified. In order to simplify the indication of corresponding requirements, the same numbering of clauses and subclauses is used as in IEC 62771-1. Amendments to these clauses and subclauses are giv

38、en under the same numbering, whilst additional subclauses are numbered from 101. 62271-205 IEC:2008 5 The text of this standard is based on the following documents: FDIS Report on voting 17C/418/FDIS 17C/423/RVD Full information on the voting for the approval of this standard can be found in the rep

39、ort on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all the parts in the IEC 62271 series, under the general title High-voltage switchgear and controlgear, can be found on the IEC website. The committee has decide

40、d that the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or

41、 amended. 6 62271-205 IEC:2008 HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR Part 205: Compact switchgear assemblies for rated voltages above 52 kV 1 General 1.1 Scope This part of IEC 62271 applies to compact switchgear assemblies consisting of at least one switching device directly connected to, or shar

42、ing components with, one or more other devices such that there is an interaction between the functions of the individual devices. Such assemblies are made up of devices defined in 1.101 and are designed, tested and supplied for use as a single unit. The interaction between devices may be due to prox

43、imity, sharing of components or a combination of both. The assemblies may contain components of air insulated switchgear (AIS) only or a combination of AIS and gas insulated switchgear (GIS), so called mixed technology switchgear (MTS) and may be delivered entirely prefabricated or partially assembl

44、ed. It is not possible to define all potential arrangements of compact switchgear assemblies however four examples are shown for information in Annex A. These compact switchgear assemblies are for indoor and/or outdoor installations in systems having rated voltages above 52 kV and service frequencie

45、s of 50 Hz and 60 Hz. This standard covers the influence on performance of the interactions between devices within compact switchgear assemblies and defines ratings and test procedures for these assemblies. IEC 62271-1 is applicable if not stated otherwise. This standard does not apply to switchgear

46、 assemblies consisting solely of GIS which are covered by 62271-203. 1.101 Objective The objective of this standard is to respond to the increasing use of compact switchgear assemblies that perform the functions of a number of separate devices and their controlgear. Numerous arrangements are possibl

47、e and this standard provides guidance on basic types of assemblies which might be envisaged. As there are potential interactions between devices within such assemblies, it is necessary to consider the standardization requirements for the assembly in its entirety. The devices, defined by IEC standard

48、s, which may form part of a compact switchgear assembly are listed below: 62271-205 IEC:2008 7 Switching devices: Circuit-breakers IEC 62271-100 Disconnectors/Earthing switches IEC 62271-102 Switches IEC 60265-2 Disconnecting circuit-breakers IEC 62271-108 Devices: Instrument transformers Current tr

49、ansformers IEC 60044-1, IEC 60044-8 Voltage transformers IEC 60044-2, IEC 60044-5, IEC 60044-7 Combined transformers IEC 60044-3 Surge arresters IEC 60099-4 Bushings IEC 60137 Insulators IEC 61462, IEC 62155 Cable connections IEC 62271-209 Transformer connections IEC 61639 Each switching device, device and their controlgear forming part of a compact switchgear assembly shall comply with