IEC 62052-21-2004 Electricity metering equipment (a.c.) - General requirements tests and test conditions - Part 21 Tariff and load control equipment《电量测量设备(交流).一般要求、试验和试验条件.第21部分 资费和负荷控制设备》.pdf

《IEC 62052-21-2004 Electricity metering equipment (a.c.) - General requirements tests and test conditions - Part 21 Tariff and load control equipment《电量测量设备(交流).一般要求、试验和试验条件.第21部分 资费和负荷控制设备》.pdf》由会员分享，可在线阅读，更多相关《IEC 62052-21-2004 Electricity metering equipment (a.c.) - General requirements tests and test conditions - Part 21 Tariff and load control equipment《电量测量设备(交流).一般要求、试验和试验条件.第21部分 资费和负荷控制设备》.pdf（50页珍藏版）》请在麦多课文档分享上搜索。

1、 INTERNATIONAL STANDARD IEC 62052-21First edition 2004-05Electricity metering equipment (a.c.) General requirements, tests and test conditions Part 21: Tariff and load control equipment Reference number IEC 62052-21:2004(E) Publication numbering As from 1 January 1997 all IEC publications are issued

2、 with a designation in the 60000 series. For example, IEC 34-1 is now referred to as IEC 60034-1. Consolidated editions The IEC is now publishing consolidated versions of its publications. For example, edition numbers 1.0, 1.1 and 1.2 refer, respectively, to the base publication, the base publicatio

3、n incorporating amendment 1 and the base publication incorporating amendments 1 and 2. Further information on IEC publications The technical content of IEC publications is kept under constant review by the IEC, thus ensuring that the content reflects current technology. Information relating to this

4、publication, including its validity, is available in the IEC Catalogue of publications (see below) in addition to new editions, amendments and corrigenda. Information on the subjects under consideration and work in progress undertaken by the technical committee which has prepared this publication, a

5、s well as the list of publications issued, is also available from the following: IEC Web Site (www.iec.ch) Catalogue of IEC publications The on-line catalogue on the IEC web site (www.iec.ch/searchpub) enables you to search by a variety of criteria including text searches, technical committees and d

6、ate of publication. On-line information is also available on recently issued publications, withdrawn and replaced publications, as well as corrigenda. IEC Just Published This summary of recently issued publications (www.iec.ch/online_news/ justpub) is also available by email. Please contact the Cust

7、omer Service Centre (see below) for further information. Customer Service Centre If you have any questions regarding this publication or need further assistance, please contact the Customer Service Centre: Email: custserviec.ch Tel: +41 22 919 02 11 Fax: +41 22 919 03 00 INTERNATIONAL STANDARD IEC 6

8、2052-21First edition 2004-05Electricity metering equipment (a.c.) General requirements, tests and test conditions Part 21: Tariff and load control equipment IEC 2004 Copyright - all rights reserved No part of this publication may be reproduced or utilized in any form or by any means, electronic or m

9、echanical, including photocopying and microfilm, without permission in writing from the publisher. International Electrotechnical Commission, 3, rue de Varemb, PO Box 131, CH-1211 Geneva 20, Switzerland Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmailiec.ch Web: www.iec.ch X For

10、price, see current catalogue PRICE CODE Commission Electrotechnique Internationale International Electrotechnical Commission 2 62052-21 IEC:2004(E) CONTENTS FOREWORD.4 INTRODUCTION.6 1 Scope.7 2 Normative references.7 3 Terms and definitions .8 3.1 General definitions9 3.2 Definitions related to ele

11、ctronic ripple control receivers.9 3.3 Definitions related to the ripple control code and to the control element 10 3.4 Definitions related to time switches .11 3.5 Definitions related to the output elements12 3.6 Definitions of mechanical elements .13 3.7 Definitions of insulations .14 3.8 Definiti

12、ons of influence quantities 15 3.9 Definition of tests16 4 Standard electrical values 16 4.1 Standard reference voltage (U n )16 4.2 Standard reference frequency (f n ) .16 5 Mechanical requirements and tests 16 5.1 General mechanical requirements .16 5.2 Case.17 5.3 Window.18 5.4 Terminals, termina

13、l block(s), protective earth terminal.18 5.5 Terminal cover(s)19 5.6 Clearance and creepage distances19 5.7 Insulating encased tariff and load control equipment of protective class II .20 5.8 Resistance to heat and fire20 5.9 Protection against penetration of dust and water .21 5.10 Void21 5.11 Void

14、21 5.12 Marking of tariff and load control equipment 22 6 Climatic conditions, requirements and tests22 6.1 Temperature range22 6.2 Relative humidity.23 6.3 Tests of the effect of the climatic environments .23 7 Electrical requirements and tests24 7.1 Supply voltage.24 7.2 Heating.26 7.3 Insulation2

15、6 7.4 Output elements28 7.5 Functional requirements and tests.32 7.6 Electromagnetic compatibility (EMC) .32 7.7 Radio interference suppression.35 62052-21 IEC:2004(E) 3 8 Test conditions and type test35 8.1 Test conditions35 8.2 Type test.35 Annex A (normative) Relationship between ambient air temp

16、erature and relative humidity36 Annex B (normative) Reference and limiting values of the influence quantities37 Annex C (normative) Electromagnet for testing the influence of externally produced magnetic fields .38 Annex D (informative) Test set-up for EMC tests.39 Annex E (informative) Test schedul

17、e.40 Annex F (informative) Acceptance tests 42 Bibliographie.44 Figure A.1 Relationship between ambient air temperature and relative humidity 36 Figure C.1 Electromagnet for testing the influence of externally produced magnetic fields 38 Figure D.1 Test set-up for the test of immunity to electromagn

18、etic RF fields 39 Figure D.2 Test set-up for fast transient burst test .39 Table 1 Clearances and creepage distances for insulating encased tariff and load control equipment of protective class I20 Table 2 Clearances and creepage distances for insulating encased tariff and load control equipment of

19、protective class II.20 Table 3 Temperature range23 Table 4 Relative humidity.23 Table 5 Voltage range24 Table 6 Power consumption.25 Table 7 Rated breaking voltages28 Table 8 Rated breaking currents 29 Table B.1 Reference and limiting values 37 Table E.1 Test schedule 40 Table F.1 Single sample plan

20、.43 Table F.2 Double sample plan43 4 62052-21 IEC:2004(E) INTERNATIONAL ELECTROTECHNICAL COMMISSION _ ELECTRICITY METERING EQUIPMENT (AC) GENERAL REQUIREMENTS, TESTS AND TEST CONDITIONS Part 21: Tariff and load control equipment FOREWORD 1) The International Electrotechnical Commission (IEC) is a wo

21、rldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other

22、 activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the su

23、bject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions

24、determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National C

25、ommittees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in w

26、hich they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publi

27、cation and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure

28、that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any

29、nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the refere

30、nced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. Interna

31、tional Standard IEC 62052-21 has been prepared by IEC technical committee 13: Equipment for electrical energy measurement and load control. This standard, in conjunction with IEC 62054-11 and IEC 62054-21, cancels and replaces IEC 61038:1990, Electricity metering Tariff and load control Particular r

32、equirements for time switches and all amendments.This standard is to be used in conjunction with the relevant parts of the IEC 62054 and the IEC 62059 series. The text of this standard is based on the following documents: FDIS Report on voting 13/1307/FDIS 13/1316/RVD Full information on the voting

33、for the approval of this standard can be found in the report on voting indicated in the above table. 62052-21 IEC:2004(E) 5 This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. The committee has decided that the contents of this publication will remain unchanged until

34、 2013. At this date, the publication will be reconfirmed; withdrawn; replaced by a revised edition, or amended. A bilingual version of this standard may be issued at a later date. 6 62052-21 IEC:2004(E) INTRODUCTION This standard distinguishes between protective class I and protective class II tarif

35、f and load control equipment. The test levels are regarded as minimum values to guarantee the proper functioning of the equipment under normal working conditions. For special application, other test levels might be necessary and should be agreed on between the user and the manufacturer. For informat

36、ion, the relevant parts of IEC 62052, IEC 62054 and IEC 62059 are listed: IEC 62052-21 Electricity metering (a.c.) General requirements, tests and test conditions Part 21: Tariff and load control equipment ( Replaces the general requirements of IEC 61037 and IEC 61038.) IEC 62054-11 Electricity mete

37、ring (a.c.) Tariff and load control Part 11: Particular requirements for electronic ripple control receivers ( Replaces the particular requirements of IEC 61037.) IEC 62054-21 Electricity metering (a.c.) Tariff and load control Part 21: Particular requirements for time switches 1( Replaces the parti

38、cular requirements of IEC 61038.) IEC 62059-11 Electricity metering equipment (a.c.) Dependability Part 11: General concepts IEC 62059-21 Electricity metering equipment (a.c.) Dependability Part 21: Collection of meter dependability data from the field IEC 62059-41 Electricity metering equipment (a.

39、c.) Dependability Part 41: Reliability prediction 2 1To be published. 2To be published. 62052-21 IEC:2004(E) 7 ELECTRICITY METERING EQUIPMENT (AC) GENERAL REQUIREMENTS, TESTS AND TEST CONDITIONS Part 21: Tariff and load control equipment 1 Scope This part of IEC 62052 specifies general requirements

40、for the type test of newly manufactured indoor tariff and load control equipment, like electronic ripple control receivers and time switches that are used to control electrical loads, multi-tariff registers and maximum demand indicator devices. This standard gives no requirements for constructional

41、details internal to the tariff and load control equipment. In the case where tariff and load control functionality is integrated into multifunction electricity metering equipment, the relevant parts of this standard apply. This standard does not cover the acceptance tests and the conformity tests. N

42、evertheless, an example of what could be an acceptance test is given in Annex F. The dependability aspect is covered by the documents of the IEC 62059 series. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only

43、the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60050-300:2001 International Electrotechnical Vocabulary (IEV) Electrical and electronic measurements and measuring instruments Part 311: General terms relating to

44、 measurements Part 312: General terms relating to electrical measurements Part 313: Types of electrical measuring instruments Part 314: Specific terms according to the type of instrument IEC 60060-1:1989, High-voltage test techniques Part 1: General definitions and test requirements IEC 60068-2-1:19

45、90, Environmental testing Part 2: Tests Tests A: Cold IEC 60068-2-2:1974, Environmental testing Part 2: Tests Tests B: Dry heat IEC 60068-2-6:1995, Environmental testing Part 2: Tests Test Fc: Vibration (sinusoidal) IEC 60068-2-27:1987, Environmental testing Part 2: Tests Test Ea and guidance: Shock

46、 IEC 60068-2-30:1980, Environmental testing Part 2: Tests Test Db and guidance: Damp heat, cyclic (12 + 12-hour cycle) IEC 60068-2-75:1997, Environmental testing Part 2-75: Tests Test Eh: Hammer test IEC 60085:1984, Thermal evaluation and classification of electrical insulation 8 62052-21 IEC:2004(E

47、) IEC 60269-3-1:1994, Low-voltage fuses Part 3-1: Supplementary requirements for fuses for use by unskilled persons (fuses mainly for household and similar applications) Sections I to IV IEC 60417-2:1998, Graphical symbols for use on equipment Part 2: Symbol originals Amendment 1(2000) IEC 60529:198

48、9, Degrees of protection provided by enclosures (IP Code) IEC 60695-2-10:2000, Fire Hazard testing Part 2-10: Glowing/hot-wire based test methods Glow-wire apparatus and common test procedures IEC 60695-2-11:2000, Fire hazard testing Part 2-11: Glowing/hot-wire based test methods Glow-wire flammabil

49、ity test method for end-products IEC 60721-3-3:1994, Classification of environmental conditions Part 3: Classification of groups of environmental parameters and their severities Section 3: Stationary use at weather protected locations IEC 61000-4-2:1995, Electromagnetic compatibility (EMC) Part 4-2: Testing and measure- ment techniq