IEC 61969-3-2011 Mechanical structures for electronic equipment - Outdoor enclosures - Part 3 Environmental requirements tests and safety aspects《电子设备的机械结构.户外机壳.第3部分 环境要求 测试和安全性等》.pdf

《IEC 61969-3-2011 Mechanical structures for electronic equipment - Outdoor enclosures - Part 3 Environmental requirements tests and safety aspects《电子设备的机械结构.户外机壳.第3部分 环境要求 测试和安全性等》.pdf》由会员分享，可在线阅读，更多相关《IEC 61969-3-2011 Mechanical structures for electronic equipment - Outdoor enclosures - Part 3 Environmental requirements tests and safety aspects《电子设备的机械结构.户外机壳.第3部分 环境要求 测试和安全性等》.pdf（30页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 61969-3 Edition 2.0 2011-11 INTERNATIONAL STANDARD NORME INTERNATIONALE Mechanical structures for electronic equipment Outdoor enclosures Part 3: Environmental requirements, tests and safety aspects Structures mcaniques pour quipement lectronique Enveloppes de plein air Partie 3: Exigences envi

2、ronnementales, essais et aspects de la scurit IEC61969-3:2011 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2011 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanic

3、al, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the addres

4、s below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photoco

5、pie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de l

6、a CEI de votre pays de rsidence. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all elec

7、trical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch

8、/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publicatio

9、ns. Just Published details twice a month all new publications released. Available on-line and also by email. Electropedia: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equiva

10、lent terms in additional languages. Also known as the International Electrotechnical Vocabulary online. Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact u

11、s: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparente

12、s. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue

13、 en-ligne de la CEI vous permet deffectuer des recherches en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Il donne aussi des informations sur les projets et les publications retires ou remplaces. Just Published CEI: www.iec.ch/online_news/justpub Restez inform sur les nouvel

14、les publications de la CEI. Just Published dtaille deux fois par mois les nouvelles publications parues. Disponible en-ligne et aussi par email. Electropedia: www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 20 000 termes et dfi

15、nitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International en ligne. Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette publication

16、 ou si vous avez des questions, visitez le FAQ du Service clients ou contactez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC 61969-3 Edition 2.0 2011-11 INTERNATIONAL STANDARD NORME INTERNATIONALE Mechanical structures for electronic equipment Outdoor enclosures Part 3: Envi

17、ronmental requirements, tests and safety aspects Structures mcaniques pour quipement lectronique Enveloppes de plein air Partie 3: Exigences environnementales, essais et aspects de la scurit INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE M ICS 31.240 PRICE CODE

18、CODE PRIX ISBN 978-2-88912-761-0 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale 2 61969-3 IEC:2011 CONTENTS FOREWORD . 3 INTRODUCTION . 5 1 Scope . 6 2 Normative references . 6 3 Terms and definitions . 7 4 Classifi

19、cation of environmental conditions 7 5 Test conditions . 8 5.1 General . 8 5.2 Climatic tests 8 5.3 Biological tests 8 5.4 Tests of resistance against chemically active substances 9 5.5 Tests of resistance against mechanically active substances 9 6 Mechanical tests. 9 6.1 General . 9 6.2 Dynamic tes

20、t . 10 6.3 Lifting and stiffness test 10 7 Safety aspects 11 7.1 General . 11 7.2 Locking devices . 11 7.3 Vandalism resistance 11 7.4 Bullet resistance (optional) 12 8 Seismic requirements . 12 9 Electromagnetic shielding performance 12 10 Thermal management . 12 11 Noise emission . 12 Table 1 Clim

21、atic conditions for environmental classes 1 and 2 . 8 Table 2 Biological tests 8 Table 3 Tests of resistance against chemically active substances 9 Table 4 Tests of resistance against mechanically active substances 9 Table 5 Vibration and shock test 10 Table 6 Safety aspects 11 61969-3 IEC:2011 3 IN

22、TERNATIONAL ELECTROTECHNICAL COMMISSION _ MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT OUTDOOR ENCLOSURES Part 3: Environmental requirements, tests and safety aspects FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all nati

23、onal electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technica

24、l Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. I

25、nternational, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The

26、 formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendatio

27、ns for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end us

28、er. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication

29、 shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent c

30、ertification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal

31、 injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative referen

32、ces cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for id

33、entifying any or all such patent rights. International Standard IEC 61969-3 has been prepared by subcommittee 48D: Mechanical structures for electronic equipment, of IEC technical committee 48: Electromechanical components and mechanical structures for electronic equipment. This second edition cance

34、ls and replaces the first edition issued in 2001. It constitutes a technical revision. The main technical changes with regard to the previous edition are as follows. Table 1 and Table 6 have been extended with requirements and tests, relevant for outdoor conditions. 4 61969-3 IEC:2011 The text of th

35、is standard is based on the following documents: FDIS Report on voting 48D/483/FDIS 48D/497/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. A list of all parts of IEC 61969 series, under the general title Mechani

36、cal structures for electronic equipment Outdoor enclosures, can be found on the IEC website. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated o

37、n the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. 61969-3 IEC:2011 5 INTRODUCTION IEC 61969-3 Ed.2.0 provides basic environmental test requirements

38、 to be used in the absence of local regulatory or application specific environmental test requirements. This provides manufacturers and users of generic outdoor enclosure solutions with minimum performance compliance criteria; thermal solutions pending on the environment an outdoor enclosure is subj

39、ected to. Since forced air heat dissipation and acoustic noise are closely related, noise limitations are typically defined by local regulatory limitations. Typically, it becomes the responsibility of the outdoor enclosure vendor to provide a solution for thermal management within the local regulato

40、ry noise limitations. 6 61969-3 IEC:2011 MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT OUTDOOR ENCLOSURES Part 3: Environmental requirements, tests and safety aspects 1 Scope This part of IEC 61969 specifies a set of basic environmental requirements and tests, as well as safety aspects for outdoor

41、enclosures under conditions of non-weatherprotected locations above ground. The purpose of this standard is to define a minimum level of environmental performance in order to meet requirements of storage, transport and final installation. It is the intention to establish basic environmental performa

42、nce criteria for outdoor enclosure compliance. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any

43、amendments) applies. IEC 60068 (all parts), Environmental testing IEC 60417, Graphical symbols for use on equipment IEC 60529, Degrees of protection provided by enclosures (IP code) IEC 60695-11-10, Fire hazard testing Part 11-10: Test flames 50 W horizontal and vertical flame test methods IEC 60721

44、-3-2, Classification of environmental conditions Part 3: Classification of groups of environmental parameters and their severities Section 2: Transportation IEC 60721-3-4, Classification of environmental conditions Part 3: Classification of groups of environmental parameters and their severities Sec

45、tion 4: Stationary use at non-weather-protected locations IEC 60825-1, Safety of laser products Part 1: Equipment specification and requirements IEC 60950 (all parts), Information technology equipment Safety IEC 61010, Safety requirements for electrical equipment for measurement, control, and labora

46、tory use IEC 61140 Protection against electric shock - Common aspects for installation and equipment IEC 61439-5, Low-voltage switchgear and control gear assemblies Part 5: Assemblies for power distribution in public networks IEC 61587-1, Mechanical structures for electronic equipment Tests for IEC

47、60917 and IEC 60297 Part 1, Climatic, mechanical tests and safety aspects for cabinets, racks, subracks and chassis 61969-3 IEC:2011 7 IEC 61587-2, Mechanical structures for electronic equipment Tests for IEC 60917 and 60297 Part 2: Seismic tests for cabinets and racks IEC 61587-3, Mechanical struct

48、ures for electronic equipment Tests for IEC 60917 and IEC 60297 Part 3: Electromagnetic shielding performance tests for cabinets, racks and subracks IEC 62194, Methods of evaluating the thermal performance of enclosures IEC 62262, Degrees of protection provided by enclosures for electrical equipment

49、 against external mechanical impacts (IK code) IEC 62305-4, Protection against lightning Part 4: Electrical and electronic systems within structures ISO 2533, Standard atmosphere ISO 3744, Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engeneering methods for an essentially free field over a reflecting plane