IEC 61869-2-2012 Instrument transformers - Part 2 Additional requirements for current transformers《仪表变压器.第2部分 电流变压器用附加要求》.pdf

《IEC 61869-2-2012 Instrument transformers - Part 2 Additional requirements for current transformers《仪表变压器.第2部分 电流变压器用附加要求》.pdf》由会员分享，可在线阅读，更多相关《IEC 61869-2-2012 Instrument transformers - Part 2 Additional requirements for current transformers《仪表变压器.第2部分 电流变压器用附加要求》.pdf（144页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 61869-2 Edition 1.0 2012-09 INTERNATIONAL STANDARD NORME INTERNATIONALE Instrument transformers Part 2: Additional requirements for current transformers Transformateurs de mesure Partie 2: Exigences supplmentaires concernant les transformateurs de courant IEC61869-2:2012 THIS PUBLICATION IS COP

2、YRIGHT PROTECTED Copyright 2012 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either I

3、EC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits d

4、e reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du

5、pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de

6、Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC

7、 publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Useful links: IEC publications search - www.iec.ch/searchpub The advanced search enables you to

8、 find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new p

9、ublications released. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms in additional languages.

10、Also known as the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. A propos de la CEI La Commission Electr

11、otechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. V

12、euillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub La recherche avance vous permet de trouver des publications CEI en utilisant diffrents critres (numro de rfrence, texte, c

13、omit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications de la CEI. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi

14、 une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel

15、 Vocabulaire Electrotechnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 61869-2 Edition 1.0 2012-09 INTERNATIONAL STANDARD NORME INTERNATIONALE Ins

16、trument transformers Part 2: Additional requirements for current transformers Transformateurs de mesure Partie 2: Exigences supplmentaires concernant les transformateurs de courant INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE XB ICS 17.220.20 PRICE CODE CODE P

17、RIX ISBN 978-2-83220-293-7 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu c

18、ette publication via un distributeur agr. 2 61869-2 IEC:2012 CONTENTS FOREWORD . 5 1 Scope . 8 2 Normative references . 8 3 Terms and definitions . 8 3.1 General definitions 8 3.3 Definitions related to current ratings 9 3.4 Definitions related to accuracy 10 3.7 Index of abbreviations . 18 5 Rating

19、s . 20 5.3 Rated insulation levels 20 5.3.2 Rated primary terminal insulation level . 20 5.3.5 Insulation requirements for secondary terminals . 20 5.3.201 Inter-turn insulation requirements . 20 5.5 Rated output . 20 5.5.201 Rated output values . 20 5.5.202 Rated resistive burden values 20 5.6 Rate

20、d accuracy class 21 5.6.201 Measuring current transformers 21 5.6.202 Protective current transformers 22 5.6.203 Class assignments for selectable-ratio current transformers . 26 5.201 Standard values for rated primary current . 26 5.202 Standard values for rated secondary current . 27 5.203 Standard

21、 values for rated continuous thermal current . 27 5.204 Short-time current ratings . 27 5.204.1 Rated short-time thermal current (Ith) . 27 5.204.2 Rated dynamic current (Idyn) 27 6 Design and construction . 27 6.4 Requirements for temperature rise of parts and components 27 6.4.1 General 27 6.13 Ma

22、rkings . 27 6.13.201 Terminal markings 27 6.13.202 Rating plate markings . 28 7 Tests 30 7.1 General 30 7.1.2 Lists of tests . 30 7.2 Type tests . 31 7.2.2 Temperature-rise test . 31 7.2.3 Impulse voltage withstand test on primary terminals . 33 7.2.6 Tests for accuracy 33 7.2.201 Short-time current

23、 tests 35 7.3 Routine tests 36 7.3.1 Power-frequency voltage withstand tests on primary terminals . 36 7.3.5 Tests for accuracy 36 7.3.201 Determination of the secondary winding resistance (Rct) . 38 7.3.202 Determination of the secondary loop time constant (Ts) 38 61869-2 IEC:2012 3 7.3.203 Test fo

24、r rated knee point e.m.f. (Ek) and exciting current at Ek39 7.3.204 Inter-turn overvoltage test 39 7.4 Special tests . 40 7.4.3 Measurement of capacitance and dielectric dissipation factor . 40 7.4.6 Internal arc fault test 40 7.5 Sample tests . 41 7.5.1 Determination of the remanence factor . 41 7.

25、5.2 Determination of the instrument security factor (FS) of measuring current transformers 41 Annex 2A (normative) Protective current transformers classes P, PR . 42 Annex 2B (normative) Protective current transformer classes for transient performance . 47 Annex 2C (normative) Proof of low-leakage r

26、eactance type . 63 Annex 2D (informative) Technique used in temperature rise test of oil-immersed transformers to determine the thermal constant by an experimental estimation . 64 Annex 2E (informative) Alternative measurement of the ratio error () 66 Annex 2F (normative) Determination of the turns

27、ratio error . 68 Figure 201 Duty cycles 15 Figure 202 Primary time constant TP16 Figure 203 Secondary linked flux for different fault inception angles 17 Figure 2A.1 Vector Diagram . 42 Figure 2A.2 Error triangle . 43 Figure 2A.3 Typical current waveforms 44 Figure 2A.4 Basic circuit for 1:1 current

28、 transformer 44 Figure 2A.5 Basic circuit for current transformer with any ratio. 45 Figure 2A.6 Alternative test circuit . 45 Figure 2B.1 Short-circuit current for two different fault inception angles . 48 Figure 2B.2 max(t) as the curve of the highest flux values, considering all relevant fault in

29、ception angles . 48 Figure 2B.3 Relevant time ranges for calculation of transient factor . 49 Figure 2B.4 Determination of Ktf in time range 1 at 50 Hz for Ts = 1,8 s . 50 Figure 2B.5 Determination of Ktf in time range 1 at 60 Hz for Ts = 1,5 s . 50 Figure 2B.6 Determination of Ktf in time range 1 a

30、t 16,7 Hz for Ts = 5.5 s . 50 Figure 2B.7 Limiting the magnetic flux by considering core saturation 52 Figure 2B.8 Basic circuit 53 Figure 2B.9 Determination of remanence factor by hysteresis loop 55 Figure 2B.10 Circuit for d.c. method . 56 Figure 2B.11 Time-amplitude and flux-current diagrams 56 F

31、igure 2B.12 Recordings with shifted flux base line . 57 Figure 2B.13 Circuit for capacitor discharge method 58 Figure 2B.14 Typical records for capacitor discharge method 59 Figure 2B.15 Measurement of error currents 60 Figure 2D.1 Graphical extrapolation to ultimate temperature rise . 65 Figure 2E.

32、1 Simplified equivalent circuit of the current transformer 66 4 61869-2 IEC:2012 Table 201 Limits of ratio error and phase displacement for measuring current transformers (classes 0,1 to 1) 21 Table 202 Limits of ratio error and phase displacement for measuring current transformers (classes 0,2S and

33、 0,5S) . 22 Table 203 Limits of ratio error for measuring current transformers (classes 3 and 5) 22 Table 204 Characterisation of protective classes . 23 Table 205 Error limits for protective current transformers class P and PR 23 Table 206 Error limits for TPX, TPY and TPZ current transformers. 25

34、Table 207 Specification Methods for TPX, TPY and TPZ current transformers . 26 Table 208 Marking of terminals 28 Table 10 List of tests . 31 61869-2 IEC:2012 5 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ INSTRUMENT TRANSFORMERS Part 2: Additional requirements for current transformers FOREWORD 1) The

35、 International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and

36、 electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical com

37、mittees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization f

38、or Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as closely as possible, an international consensus of opinion on the relevant subjects since each technical committ

39、ee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is a

40、ccurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and reg

41、ional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, i

42、n some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or age

43、nts including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of,

44、 or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some

45、of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. This International Standard IEC 61869-2 Ed.1.0 has been prepared by committee 38: Instrument transformers. This first edition of IEC 61869-2 c

46、ancels and replaces the first edition of IEC 60044-1, published in 1996, and its Amendment 1 (2000) and Amendment 2 (2002), and the first edition of IEC 60044-6, published in 1992. Additionally it introduces technical innovations in the standardization and adaptation of the requirements for current

47、transformers for transient performance. The text of this standard is based on the following documents: FDIS Report on voting 38/435/FDIS 38/437/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. 6 61869-2 IEC:2012 T

48、his publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all the parts in the IEC 61869 series, published under the general title Instrument transformers, can be found on the IEC website. This Part 2 is to be used in conjunction with, and is based on, IEC 61869-1

49、:2007, General Requirements however the reader is encouraged to use its most recent edition. This Part 2 follows the structure of IEC 61869-1:2007 and supplements or modifies its corresponding clauses. When a particular clause/subclause of Part 1 is not mentioned in this Part 2, that clause/subclause applies as far as is reasonable. When this standard states “addition”, “modification” or “re