IEC 61755-3-32-2015 Fibre optic interconnecting devices and passive components - Connector optical interfaces - Part 3-32 Connector parameters of non-dispersion shifted single mode.pdf

《IEC 61755-3-32-2015 Fibre optic interconnecting devices and passive components - Connector optical interfaces - Part 3-32 Connector parameters of non-dispersion shifted single mode.pdf》由会员分享，可在线阅读，更多相关《IEC 61755-3-32-2015 Fibre optic interconnecting devices and passive components - Connector optical interfaces - Part 3-32 Connector parameters of non-dispersion shifted single mode.pdf（42页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 61755-3-32 Edition 1.0 2015-06 INTERNATIONAL STANDARD NORME INTERNATIONALE Fibre optic interconnecting devices and passive components Connector optical interfaces Part 3-32: Connector parameters of non-dispersion shifted single mode physically contacting fibres Angled thermoset epoxy rectangula

2、r ferrules Dispositifs dinterconnexion et composants passifs fibres optiques Interfaces optiques de connecteurs Partie 3-32: Paramtres de connecteurs pour fibres unimodales dispersion non dcale, en contact physique Frules rectangulaires avec angle en poxy thermodurcissable IEC 61755-3-32:2015-06(en-

3、fr) colour inside THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2015 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, wi

4、thout permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Co

5、mmittee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de

6、lIEC ou du Comit national de lIEC du pays du demandeur. Si vous avez des questions sur le copyright de lIEC ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de lIEC de votre pays de rsidence. IEC Central Office

7、Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic an

8、d related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. IEC Catalogue - webstore.iec.ch/catalogue The stand-alone appl

9、ication for consulting the entire bibliographical information on IEC International Standards, Technical Specifications, Technical Reports and other documents. Available for PC, Mac OS, Android Tablets and iPad. IEC publications search - www.iec.ch/searchpub The advanced search enables to find IEC pu

10、blications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications

11、released. Available online and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms in 15 additional languages. Also known

12、 as the International Electrotechnical Vocabulary (IEV) online. IEC Glossary - std.iec.ch/glossary More than 60 000 electrotechnical terminology entries in English and French extracted from the Terms and Definitions clause of IEC publications issued since 2002. Some entries have been collected from

13、earlier publications of IEC TC 37, 77, 86 and CISPR. IEC Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. A propos de lIEC La Commission Electrotechnique Internati

14、onale (IEC) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications IEC Le contenu technique des publications IEC est constamment revu. Veuillez vous assurer que v

15、ous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue IEC - webstore.iec.ch/catalogue Application autonome pour consulter tous les renseignements bibliographiques sur les Normes internationales, Spcifications techniques, Rapports techniques et autres document

16、s de lIEC. Disponible pour PC, Mac OS, tablettes Android et iPad. Recherche de publications IEC - www.iec.ch/searchpub La recherche avance permet de trouver des publications IEC en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets

17、 et les publications remplaces ou retires. IEC Just Published - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications IEC. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le p

18、remier dictionnaire en ligne de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans 15 langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (IEV) en ligne. Glossaire IEC - std.

19、iec.ch/glossary Plus de 60 000 entres terminologiques lectrotechniques, en anglais et en franais, extraites des articles Termes et Dfinitions des publications IEC parues depuis 2002. Plus certaines entres antrieures extraites des publications des CE 37, 77, 86 et CISPR de lIEC. Service Clients - web

20、store.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 61755-3-32 Edition 1.0 2015-06 INTERNATIONAL STANDARD NORME INTERNATIONALE Fibre optic interconnecting devices and passive components Connector optical inte

21、rfaces Part 3-32: Connector parameters of non-dispersion shifted single mode physically contacting fibres Angled thermoset epoxy rectangular ferrules Dispositifs dinterconnexion et composants passifs fibres optiques Interfaces optiques de connecteurs Partie 3-32: Paramtres de connecteurs pour fibres

22、 unimodales dispersion non dcale, en contact physique Frules rectangulaires avec angle en poxy thermodurcissable INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE ICS 33.180.20 ISBN 978-2-8322-2713-8 Registered trademark of the International Electrotechnical Commis

23、sion Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. colour inside 2 IEC 61755-3-32:2015 IEC 2015 CONTE

24、NTS FOREWORD . 3 1 Scope 5 2 Normative references. 5 3 Description 6 4 Interface parameters 6 Annex A (informative) Theoretical worst-case connector attenuation yield percentage . 12 Annex B (informative) Minus coplanarity . 14 Annex C (informative) Minimum normal force required to achieve physical

25、contact 15 Bibliography . 19 Figure 1 Fibre numbering conventions 7 Figure 2 Interface dimensions related to lateral and angular offset 7 Figure 3 Alignment pin geometry 8 Figure 4 Interface dimensions related to longitudinal offset . 9 Figure A.1 Monte Carlo simulation of Grade C performance for 12

26、-fibre connectors . 12 Figure B.1 Illustration of fibre line and minus coplanarity parameters 14 Figure C.1 Geometry limit (GL), needed to mate 12 fibres, as a function of absolute X-angle, SX for different magnitudes of minus coplanarity and flat fibre tips 16 Figure C.2 Geometry limit (GL), needed

27、 to mate 12 fibres, as a function of absolute X-angle, SX for different magnitudes of minus coplanarity and 1 mm fibre tips 16 Table 1 Optical interface variant information . 7 Table 2 Optical interface dimensions related to lateral and angular offset for optical interface variant 2112 . 10 Table 3

28、Optical interface end face geometry dimensions related to physical contact for optical interface variant 2112 . 11 Table A.1 Grade C single channel vs. multi-fibre connector performance . 13 Table C.1 Parameter constants for 4-fibre optical interface variant K2 . 18 Table C.2 Parameter constants for

29、 8-fibre optical interface variant K3 . 18 Table C.3 Parameter constants for 12-fibre optical interface variant K4 . 18 IEC 61755-3-32:2015 IEC 2015 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS CONNECTOR OPTICAL INTERFACES Part 3-32: Connec

30、tor parameters of non-dispersion shifted single mode physically contacting fibres Angled thermoset epoxy rectangular ferrules FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC Natio

31、nal Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Public

32、ly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governm

33、ental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on

34、technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted

35、by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international u

36、niformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.

37、 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should e

38、nsure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage o

39、f any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the

40、referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. I

41、nternational Standard IEC 61755-3-32 has been prepared by subcommittee 86B: Fibre optic interconnecting devices and passive components, of IEC technical committee 86: Fibre optics. This first edition cancels and replaces IEC PAS 61755-3-32 published in 2007. This edition constitutes a technical revi

42、sion. The text of this standard is based on the following documents: FDIS Report on voting 86B/3889/FDIS 86B/3915/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. 4 IEC 61755-3-32:2015 IEC 2015 This publication ha

43、s been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts of the IEC 61755 series, under the general title Fibre optic interconnecting devices and passive components Connector optical interfaces, can be found on the IEC website. Future standards in this series will carry

44、the new general title as cited above. Titles of existing standards in this series will be updated at the time of the next edition. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch

45、“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. IMPORTANT The colour inside logo on the cover page of this publication indicates that it contains colours which are considered to be useful for

46、the correct understanding of its contents. Users should therefore print this document using a colour printer. IEC 61755-3-32:2015 IEC 2015 5 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS CONNECTOR OPTICAL INTERFACES Part 3-32: Connector parameters of non-dispersion shifted single mode p

47、hysically contacting fibres Angled thermoset epoxy rectangular ferrules 1 Scope This part of IEC 61755 defines certain dimensional limits of an angled PC rectangular thermoset (TS) ferrule optical interface in order to meet specific requirements for fibre-to-fibre interconnection. Ferrules made from

48、 the material specified in this standard are suitable for use in categories C, U, E, and O as defined in IEC 61753-1. Ferrule interface dimensions and features are contained in the IEC 61754 series, which deals with fibre optic connector interfaces. 2 Normative references The following documents, in

49、 whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60793-2-50, Optical fibres Part 2-50: Product specifications Sectional specification for class