IEC 61754-1-2013 Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 1 General and guidance《光纤互连设备和无源元件.纤维光学连接器接口.第1部分 总则和导则》.pdf

《IEC 61754-1-2013 Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 1 General and guidance《光纤互连设备和无源元件.纤维光学连接器接口.第1部分 总则和导则》.pdf》由会员分享，可在线阅读，更多相关《IEC 61754-1-2013 Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 1 General and guidance《光纤互连设备和无源元件.纤维光学连接器接口.第1部分 总则和导则》.pdf（30页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 61754-1 Edition 2.0 2013-08 INTERNATIONAL STANDARD NORME INTERNATIONALE Fibre optic interconnecting devices and passive components Fibre optic connector interfaces Part 1: General and guidance Dispositifs dinterconnexion et composants passifs fibres optiques Interfaces de connecteurs fibres opt

2、iques Partie 1: Gnralits et lignes directrices IEC 61754-1:2013 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2013 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechan

3、ical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the addr

4、ess below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photo

5、copie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de

6、 la CEI de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes Int

7、ernational Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Useful l

8、inks: IEC publications search - www.iec.ch/searchpub The advanced search enables you to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/just

9、published Stay up to date on all new IEC publications. Just Published details all new publications released. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms

10、 and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please

11、contact the Customer Service Centre: csciec.ch. A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des p

12、ublications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub La recherche avance vous permet de

13、trouver des publications CEI en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications de la CEI.

14、 Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en fr

15、anais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csc

16、iec.ch. IEC 61754-1 Edition 2.0 2013-08 INTERNATIONAL STANDARD NORME INTERNATIONALE Fibre optic interconnecting devices and passive components Fibre optic connector interfaces Part 1: General and guidance Dispositifs dinterconnexion et composants passifs fibres optiques Interfaces de connecteurs fib

17、res optiques Partie 1: Gnralits et lignes directrices INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE M ICS 33.180.20 PRICE CODE CODE PRIX ISBN 978-2-8322-1050-5 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission E

18、lectrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. 2 61754-1 IEC:2013 CONTENTS FOREWORD . 3 INTRODUCTION . 5 1 Scope 6 2 Normative refere

19、nces 6 3 Terms and definitions 6 4 Dimensioning system . 9 5 Gauges 9 6 Tolerance grades . 9 Annex A (normative) Dimensioning connector interfaces 10 A.1 General 10 A.2 Units 10 A.3 Fundamental rules . 10 Annex B (informative) Using interface standards 12 Bibliography 13 Figure 1 Plug, adaptor, and

20、receptacle for a connector examples 9 61754-1 IEC:2013 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS FIBRE OPTIC CONNECTOR INTERFACES Part 1: General and guidance FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide

21、 organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activi

22、ties, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject d

23、ealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determi

24、ned by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committe

25、es. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which th

26、ey are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication

27、and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not res

28、ponsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical c

29、ommittees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Public

30、ations. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of p

31、atent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61754-1 has been prepared by subcommittee SC86B: Fibre optic interconnecting devices and passive components, of IEC technical committee 86: Fibre optics. This second edition canc

32、els and replaces the first edition, published in 1996, and constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) general reconsideration of performance requirements; b) addition of Figure 1. 4 61754-1 IEC:2013 The

33、 text of this standard is based on the following documents: CDV Report on voting 86B/3503/CDV 86B/3602/RVC Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/

34、IEC Directives, Part 2. A list of all parts in the IEC 61754 series, published under the general title, Fibre optic interconnecting devices and passive components Fibre optic connector interfaces, can be found on the IEC website. The committee has decided that the contents of this publication will r

35、emain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. 61754-1 IEC:2013 5 INTRODUCTION An optical co

36、nnector interface is a collection of physical features on a connector assembly that defines a specified style. It consists of those minimum features that are functionally critical (i.e. work together) during the mechanical mating and unmating sequences of the connector with its counterpart component

37、. The interface defines the size, relative location and tolerance for each of the features. In addition, it defines the location for the optical datum target. This part of IEC 61754 contains those interfaces that have been standardized for international use. It consists of individual sets of plug an

38、d adaptor interfaces. Each set contains at least two counterpart interfaces that mate together. The standards therefore only ensure that the two counterpart interfaces will mate together and that they will mate with a specified fit tolerance between the mating features. It is important to emphasize

39、that the standard interfaces define physical dimensions only and that no guarantee of performance is implied, nor should be assumed, for connectors that comply with the standards. Manufacturers using the standards are responsible for positioning the optical fibre or device port at the optical datum

40、target location with the accuracy necessary to meet their required performance. An optical connector, by definition, mates with another optical component. Typically, the mating component is another optical connector. In many cases, however, the mating component is not another connector but rather an

41、 optical component such as a switch, a branching device or an active device. The portion of the component that contains the mating features to receive and position the connector is called an adaptor. This standard makes a distinction between a connector interface and an adaptor interface. An adaptor

42、 interface may not contain an optical datum target as in the case where two connector plugs are engaged and are aligned by an alignment sleeve. However, the adaptor does contain an optical datum target whenever it positions an optical fibre or optical fibre waveguide, as in an active device or branc

43、hing device. 6 61754-1 IEC:2013 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS FIBRE OPTIC CONNECTOR INTERFACES Part 1: General and guidance 1 Scope This part of IEC 61754 covers general information on the subject of fibre optic connector interfaces. It includes references, definitions a

44、nd rules for creating and interpreting the standard drawings. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the

45、latest edition of the referenced document (including any amendments) applies. IEC 60050-731:1991, International electrotechnical vocabulary Chapter 731: Optical fibre communication IEC 60874-1:2011, Fibre optic interconnecting devices and passive components Connectors for optical fibres and cables P

46、art 1: Generic specification IEC 61754 (all parts), Fibre optic interconnecting devices and passive components Fibre optic connector intefaces 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 adaptor component that permits mating between a con

47、nector and another optical component such as a connector, an active device, a switch, a branching device, etc. 3.2 adaptor interface features involved in the mating and unmating sequences of the adaptor with the mating connector Note 1 to entry: This takes into account their size and relative locati

48、ons. Note 2 to entry: It may also include an optical datum target. 3.3 alignment device mechanical device that aligns at least one connector plug ferrule Note 1 to entry: It is generally contained in an adaptor for the purpose of aligning one or two mating connector plug ferrules coincident to a com

49、mon optical datum target. 61754-1 IEC:2013 7 3.4 basic dimension numerical value used to describe the theoretically exact size, profile, orientation, or location of a feature or datum target Note 1 to entry: It is the basis from which permissible variations are established by tolerances on other dimensions in notes, or in feature control frames. 3.5 connector interface features involved in the mating and unmating