IEC 61747-40-1-2013 Liquid crystal display devices - Part 40-1 Mechanical testing of display cover glass for mobile devices - Guidelines《液晶显示设备 第40-1部分 移动设备用显示保护玻璃的机械试验 指南》.pdf

《IEC 61747-40-1-2013 Liquid crystal display devices - Part 40-1 Mechanical testing of display cover glass for mobile devices - Guidelines《液晶显示设备 第40-1部分 移动设备用显示保护玻璃的机械试验 指南》.pdf》由会员分享，可在线阅读，更多相关《IEC 61747-40-1-2013 Liquid crystal display devices - Part 40-1 Mechanical testing of display cover glass for mobile devices - Guidelines《液晶显示设备 第40-1部分 移动设备用显示保护玻璃的机械试验 指南》.pdf（24页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 61747-40-1 Edition 1.0 2013-06 INTERNATIONAL STANDARD NORME INTERNATIONALE Liquid crystal display devices Part 40-1: Mechanical testing of display cover glass for mobile devices Guidelines Dispositifs daffichage cristaux liquides Partie 40-1: Essais mcaniques des verres protecteurs des affichag

2、es pour les dispositifs mobiles Lignes directrices IEC61747-40-1:2013 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2013 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or

3、mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact th

4、e address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la

5、 photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit natio

6、nal de la CEI de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publish

7、es International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Us

8、eful links: IEC publications search - www.iec.ch/searchpub The advanced search enables you to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.c

9、h/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000

10、 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, p

11、lease contact the Customer Service Centre: csciec.ch. A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos

12、 des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub La recherche avance vous perm

13、et de trouver des publications CEI en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications de l

14、a CEI. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et

15、 en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nou

16、s: csciec.ch. IEC 61747-40-1 Edition 1.0 2013-06 INTERNATIONAL STANDARD NORME INTERNATIONALE Liquid crystal display devices Part 40-1: Mechanical testing of display cover glass for mobile devices Guidelines Dispositifs daffichage cristaux liquides Partie 40-1: Essais mcaniques des verres protecteurs

17、 des affichages pour les dispositifs mobiles Lignes directrices INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE K ICS 31.120 PRICE CODE CODE PRIX ISBN 978-2-83220-862-5 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commi

18、ssion Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. 2 61747-40-1 IEC:2013 CONTENTS FOREWORD . 3 INTRODUCTION . 5 1 Scope . 6 2 Term

19、s and definitions . 6 3 Mechanical performance testing guidelines 7 3.1 General . 7 3.2 Mechanical testing guidelines for display cover glass for mobile devices . 8 4 Brief overview of mechanical test methods . 8 Bibliography 10 Table 1 Mechanical attributes and measurement methods . 8 61747-40-1 IE

20、C:2013 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ LIQUID CRYSTAL DISPLAY DEVICES Part 40-1: Mechanical testing of display cover glass for mobile devices Guidelines FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all nation

21、al electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical

22、Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. Int

23、ernational, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The f

24、ormal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations

25、 for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user

26、. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication s

27、hall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent cer

28、tification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal i

29、njury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative reference

30、s cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for iden

31、tifying any or all such patent rights. International Standard IEC 61747-40-1 has been prepared by IEC technical committee 110: Electronic display devices. The text of this standard is based on the following documents: FDIS Report on voting 110/464/FDIS 110/476/RVD Full information on the voting for

32、the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. 4 61747-40-1 IEC:2013 A list of all the parts in the IEC 61747 series, under the general title Liquid crystal display

33、devices, can be found on the IEC website. Future standards in this series will carry the new general title as cited above. Titles of existing standards in this series will be updated at the time of the next edition. The committee has decided that the contents of this publication will remain unchange

34、d until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. 61747-40-1 IEC:2013 5 INTRODUCTION Mobile electronic device

35、s have become increasingly sophisticated and often incorporate displays for the purposes of user interface and viewing. Such displays commonly incorporate a transparent cover glass which aids in protecting the display against the introduction of damage through routine device transport and use, as we

36、ll as occasional or accidental misuse. The purpose of this standard is to provide mechanical testing guidelines for cover glasses utilized in such applications. Such glasses may or may not be strengthened, for example via an ion-exchange process, which acts to increase mechanical strength through th

37、e introduction of a surface compressive layer. It is assumed that all measurements described in detail in individual test method standards are performed by personnel skilled in the general art of mechanical property measurements. Furthermore, it should be assured that all equipment is suitably calib

38、rated as is known to skilled personnel and that records of the calibration data and traceability are kept. 6 61747-40-1 IEC:2013 LIQUID CRYSTAL DISPLAY DEVICES Part 40-1: Mechanical testing of display cover glass for mobile devices Guidelines 1 Scope This part of IEC 61747 is a mechanical performanc

39、e testing guideline for cover glass used in electronic flat panel displays in mobile devices. This document focuses on key mechanical testing performance parameters and covers mainly strength and damage resistance attributes. The test methods will focus on the cover glass level testing only. NOTE Th

40、e glass used for cover glasses for electronic mobile devices can be chemically strengthened by an ion-exchange process. This ion exchange process increases the mechanical strength of the glass. 2 Terms and definitions For the purposes of this document, the following terms and definitions apply. 2.1

41、abraded subjected to a defined process which introduces mechanical abrasive damage to a portion of the specimen to be placed under tension during subsequent flexural strength testing, for example, biaxial flexure via ring-on-ring 2.2 as-received representative of standard sample preparation and hand

42、ling practices, and therefore free of intentional mechanical damage such as abrasion, scratching, or indentation Note 1 to entry: The strength of glass is not an intrinsic material property, and like other brittle elastic materials, is highly dependent upon the surface flaw population. The term “as-

43、received” is meant to represent the surface condition upon specimen receipt and should be distinguished from a condition where damage has been intentionally introduced prior to testing. 2.3 central tension CT tensile stress generated within the interior of a glass article which serves to counteract

44、(i.e., force balance) compressive stress acting at or near the article surface Note 1 to entry: This note applies to the French language only. 2.4 chemically strengthened subjected to a molten salt bath containing alkali ions typically larger than those residing in the glass, resulting in the genera

45、tion of residual compressive stress (2.5) and central tension (2.3) 2.5 compressive stress CS maximum residual stress in compression measured near the glass surface Note 1 to entry: This note applies to the French language only. 61747-40-1 IEC:2013 7 2.6 cover glass cover lens glass that typically p

46、rotects an optical component such as a display from damage 2.7 damage resistance ability to resist certain potential damage-inducing events such as abrasion, indentation or scratching 2.8 depth of layer DOL distance from the surface of a strengthened glass to the depth of zero stress or the depth of

47、 transition from compressive to tensile stress Note 1 to entry: The ability to approximate this depth is dependent upon the measurement methodology chosen. Note 2 to entry: This note applies to the French language only. 2.9 edge strength measured stress at failure in the case where failure is known

48、to have originated from a specimen edge 2.10 mobile device electronic device that includes a battery and is designed to be carried about by consumers 2.11 retained surface strength abraded surface strength measured stress at failure in the case where failure is known to have originated from a specim

49、en surface which has experienced a prescribed abrasion or mechanical damage event 2.12 strength stress at which a specimen fails for a given loading condition 2.13 thermally strengthened subjected to fast cooling of the glass exterior relative to the glass interior, resulting in the generation of residual compressive stress (2.5) and central tension (2.3) 3 Mechanical performance testing guidelines 3.1 General The appropriate a