IEC 61558-2-16 Edition 1.1-2013 Safety of transformers reactors power supply units and similar products for voltages up to 1100 V - Part 2-16 Particular requirements and tests for .pdf

《IEC 61558-2-16 Edition 1.1-2013 Safety of transformers reactors power supply units and similar products for voltages up to 1100 V - Part 2-16 Particular requirements and tests for .pdf》由会员分享，可在线阅读，更多相关《IEC 61558-2-16 Edition 1.1-2013 Safety of transformers reactors power supply units and similar products for voltages up to 1100 V - Part 2-16 Particular requirements and tests for .pdf（194页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 61558-2-16 Edition 1.1 2013-08 CONSOLIDATED VERSION VERSION CONSOLIDE Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V Part 2-16: Particular requirements and tests for switch mode power supply units and transformers for switch mode powe

2、r supply units Scurit des transformateurs, bobines dinductance, blocs dalimentation et produits analogues pour des tensions dalimentation jusqu 1 100 V Partie 2-16: Rgles particulires et essais pour les blocs dalimentation dcoupage et les transformateurs pour blocs dalimentation dcoupage IEC61558-2-

3、16:2009+A1:2013GROUP SAFETY PUBLICATION PUBLICATION GROUPE DE SCURIT colourinsideTHIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2013 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, ele

4、ctronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please

5、 contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y

6、 compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le

7、Comit national de la CEI de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares

8、and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been pu

9、blished. Useful links: IEC publications search - www.iec.ch/searchpub The advanced search enables you to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - web

10、store.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more

11、than 30 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further as

12、sistance, please contact the Customer Service Centre: csciec.ch. A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparente

13、s. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub La recherche avanc

14、e vous permet de trouver des publications CEI en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform sur les nouvelles public

15、ations de la CEI. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en

16、 anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions co

17、ntactez-nous: csciec.ch. IEC 61558-2-16 Edition 1.1 2013-08 CONSOLIDATED VERSION VERSION CONSOLIDE Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V Part 2-16: Particular requirements and tests for switch mode power supply units and transform

18、ers for switch mode power supply units Scurit des transformateurs, bobines dinductance, blocs dalimentation et produits analogues pour des tensions dalimentation jusqu 1 100 V Partie 2-16: Rgles particulires et essais pour les blocs dalimentation dcoupage et les transformateurs pour blocs dalimentat

19、ion dcoupage INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE ICS 29.180 ISBN 978-2-8322-1043-7 GROUP SAFETY PUBLICATION PUBLICATION GROUPE DE SCURIT Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechniq

20、ue Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. colourinsideIEC 61558-2-16 Edition 1.1 2013-08 REDLINE VERSION VERSION REDLINE Safety of transforme

21、rs, reactors, power supply units and similar products for supply voltages up to 1 100 V Part 2-16: Particular requirements and tests for switch mode power supply units and transformers for switch mode power supply units Scurit des transformateurs, bobines dinductance, blocs dalimentation et produits

22、 analogues pour des tensions dalimentation jusqu 1 100 V Partie 2-16: Rgles particulires et essais pour les blocs dalimentation dcoupage et les transformateurs pour blocs dalimentation dcoupage IEC61558-2-16:2009+A1:2013GROUP SAFETY PUBLICATION PUBLICATION GROUPE DE SCURIT colourinside 2 61558-2-16

23、IEC:2009+A1:2013 CONTENTS FOREWORD . 4 INTRODUCTION TO THE AMENDMENT . 6 1 Scope . 7 2 Normative references 9 3 Terms and definitions . 10 4 General requirements . 11 5 General notes on tests 11 6 Ratings . 11 7 Classification 11 8 Marking and other information . 11 9 Protection against electric sho

24、ck . 13 10 Change of input voltage setting . 14 11 Output voltage and output current under load 14 12 No-load output voltage 14 13 Short circuit voltage 15 14 Heating . 15 15 Short-circuit and overload protection . 15 16 Mechanical strength 16 17 Protection against harmful ingress of dust, solid obj

25、ects and moisture . 16 18 Insulation resistance, dielectric strength and leakage current 16 19 Construction . 17 20 Components . 24 21 Internal wiring . 24 22 Supply connection and other external flexible cables or cords 24 23 Terminals for external conductors . 24 24 Provisions for protective earth

26、ing 24 25 Screws and connections . 24 26 Creepage distances, clearances and distances through insulation . 24 27 Resistance to heat, fire and tracking . 40 28 Resistance to rusting 40 Annexes 41 Annex K (normative) Insulated winding wires 41 Annex AA (informative) Partial discharge (PD) test . 44 An

27、nex BB (normative) Particular requirements for associated transformers for use in switch mode power supplies with internal frequencies 500 Hz . 44 Bibliography 46 Figure 101 Diagram for dimensioning of clearances 26 Figure 102 Diagram of dimensioning creepage distances 29 61558-2-16 IEC:2009+A1:2013

28、 3 Figure 103 Permissible field strength for dimensioning of solid insulation according to Equation (1) 37 Figure 104 Test voltages 17 Table 101 Output voltages ratio 15 Table 102 Values of clearances for frequencies 30 kHz with approximately homogeneous field condition according to 4.3 of IEC 60664

29、-4 . 26 Table 103 Values of clearances for transient overvoltages or recurring peak voltages produced in the primary circuit of the SMPS for frequencies 30 kHz . 27 Table 105 Basic or supplementary insulation Minimum values of creepage distances for different frequency ranges (pollution degree 1) .

30、30 Table 106 Basic or supplementary insulation Minimum values of creepage distances for different frequency ranges (pollution degree 2) . 31 Table 107 Basic or supplementary insulation Minimum values of creepage distances for different frequency ranges (pollution degree 3) . 32 Table 108 Double or r

31、einforced insulation Minimum values of creepage distances for different frequency ranges (pollution degree 1) 33 Table 109 Double or reinforced insulation Minimum values of creepage distances for different frequency ranges (pollution degree 2) 34 Table 110 Double or reinforced insulation Minimum val

32、ues of creepage distances for different frequency ranges (pollution degree 3) 35 Table 111 Values of FIW wires with maximum overall diameter and minimum test voltages according to enamel increase 39 Table K.1 Mandrel diameter 42 Table K.2 Oven temperature . 42 4 61558-2-16 IEC:2009+A1:2013 INTERNATI

33、ONAL ELECTROTECHNICAL COMMISSION _ SAFETY OF TRANSFORMERS, REACTORS, POWER SUPPLY UNITS AND SIMILAR PRODUCTS FOR SUPPLY VOLTAGES UP TO 1 100 V Part 2-16: Particular requirements and tests for switch mode power supply units and transformers for switch mode power supply units FOREWORD 1) The Internati

34、onal Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electroni

35、c fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; a

36、ny IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also Participate in this preparation. IEC collaborates closely with the International Organization for Standar

37、dization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has repr

38、esentation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IE

39、C cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publi

40、cations. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an

41、 IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal in

42、jury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the normative references

43、 cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for ident

44、ifying any or all such patent rights. This Consolidated version of IEC 61558-2-16 bears the edition number 1.1. It consists of the first edition (2009) documents 96/330/FDIS and 96/333/RVD and its amendment 1 (2013) documents 96/401/FDIS and 96/405/RVD. The technical content is identical to the base

45、 edition and its amendment. In this Redline version, a vertical line in the margin shows where the technical content is modified by amendment 1. Additions and deletions are displayed in red, with deletions being struck through. A separate Final version with all changes accepted is available in this

46、publication. This publication has been prepared for user convenience. 61558-2-16 IEC:2009+A1:2013 5 International Standard IEC 61558-2-16 has been prepared by IEC technical committee 96: Transformers, reactors, power supply units and similar products for low voltage up to 1 100 V. This part has the

47、status of a group safety publication in accordance with IEC Guide 104 (1997): The preparation of safety publications and the use of basic safety publications and group safety publications. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. This Part 2-16 is intended

48、 to be used in conjunction with the latest edition of IEC 61558-1 and its amendments. It is based on the second edition (2005) of that standard. This part supplements or modifies the corresponding clauses in IEC 61558-1, so as to convert that publication into the IEC standard: Particular requirement

49、s and tests for switch mode power supply units and transformers for switch mode power supply units. A list of all parts of the IEC 61558 series can be found on the IEC website under the title: Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V. Future standards in this series will carry the new general tit