IEC 61439-6-2012 Low-voltage switchgear and controlgear assemblies - Part 6 Busbar trunking systems (busways)《低压开关设备和控制设备配件.第6部分 中继系统(母线槽)》.pdf

《IEC 61439-6-2012 Low-voltage switchgear and controlgear assemblies - Part 6 Busbar trunking systems (busways)《低压开关设备和控制设备配件.第6部分 中继系统(母线槽)》.pdf》由会员分享，可在线阅读，更多相关《IEC 61439-6-2012 Low-voltage switchgear and controlgear assemblies - Part 6 Busbar trunking systems (busways)《低压开关设备和控制设备配件.第6部分 中继系统(母线槽)》.pdf（90页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 61439-6 Edition 1.0 2012-05 INTERNATIONAL STANDARD NORME INTERNATIONALE Low-voltage switchgear and controlgear assemblies Part 6: Busbar trunking systems (busways) Ensembles dappareillage basse tension Partie 6: Systmes de canalisation prfabrique IEC 61439-6:2012 THIS PUBLICATION IS COPYRIGHT P

2、ROTECTED Copyright 2012 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IE

3、Cs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reprod

4、uction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du

5、demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb F

6、ax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publica

7、tions The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Useful links: IEC publications search - www.iec.ch/searchpub The advanced search enables you to find IE

8、C publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publicati

9、ons released. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms in additional languages. Also kno

10、wn as the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. A propos de la CEI La Commission Electrotechniq

11、ue Internationale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez

12、vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub La recherche avance vous permet de trouver des publications CEI en utilisant diffrents critres (numro de rfrence, texte, comit dtu

13、des,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications de la CEI. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une foi

14、s par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabul

15、aire Electrotechnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 61439-6 Edition 1.0 2012-05 INTERNATIONAL STANDARD NORME INTERNATIONALE Low-voltage

16、 switchgear and controlgear assemblies Part 6: Busbar trunking systems (busways) Ensembles dappareillage basse tension Partie 6: Systmes de canalisation prfabrique INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE X ICS 29.130.20 PRICE CODE CODE PRIX ISBN 978-2-832

17、20-084-1 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication v

18、ia un distributeur agr. 2 61439-6 IEC:2012 CONTENTS FOREWORD . 3 1 Scope . 5 2 Normative references . 5 3 Terms and definitions . 6 4 Symbols and abbreviations . 8 5 Interface characteristics . 8 6 Information . 12 7 Service conditions 12 8 Constructional requirements . 13 9 Performance requirements

19、 . 14 10 Design verifications 15 11 Routine verifications . 27 Annexes . 28 Annex C (informative) Specification schedule 29 Annex D (informative) Design verification 33 Annex AA (informative) Voltage drop of the system 34 Annex BB (informative) Phase conductor characteristics 35 Annex CC (informativ

20、e) Fault-loop zero-sequence impedances 37 Annex DD (informative) Fault-loop resistances and reactances 39 Annex EE (informative) Determination of the magnetic field in the vicinity of the BTS 41 Bibliography 42 Figure 101 Mechanical load test of a straight unit 16 Figure 102 Mechanical load test of

21、a joint 16 Figure 103 Test arrangement for verification of a fire-barrier BTU 27 Figure BB.1 Phase conductors characteristics determination . 35 Figure CC.1 Fault loop zero-sequence impedances determination . 37 Figure DD.1 Fault loop resistances and reactances determination . 39 Figure EE.1 Magneti

22、c field measurement arrangement 41 Table 101 Rated diversity factor for a tap-off unit . 10 Table 102 Phase conductor characteristics 11 Table 103 Fault-loop characteristics 11 Table 104 Characteristics to be used for fault currents calculations . 12 Table 105 Conditioning for the thermal cycling te

23、st 18 Table C.1 User specification schedule . 29 Table D.1 Design verifications . 33 61439-6 IEC:2012 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES Part 6: Busbar trunking systems (busways) FOREWORD 1) The International Electrotechnical Commission (I

24、EC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in additi

25、on to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee intereste

26、d in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with

27、conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC

28、 National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for t

29、he way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between an

30、y IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformi

31、ty. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members

32、of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or an

33、y other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may b

34、e the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61439-6 has been prepared by subcommittee 17D: Low-voltage switchgear and controlgear assemblies, of IEC technical committee 17: Switchgear and controlgear. Thi

35、s first edition of IEC 61439-6 cancels and replaces the third edition of IEC 60439-2 (2000) and its Amendment 1 (2005), and constitutes a technical revision. This edition of IEC 61439-6 includes the following significant technical changes with respect to the latest edition of IEC 60439-2: alignment

36、on the second edition of IEC 61439-1 (2011) regarding the structure and technical content, as applicable; introduction of new verifications, accordingly; correction of inconsistencies in resistance, reactance and impedance measurements and calculations; numerous editorial improvements. 4 61439-6 IEC

37、:2012 The text of this standard is based on the following documents: FDIS Report on voting 17D/452/FDIS 17D/454/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with

38、 the ISO/IEC Directives, Part 2. This standard is to be read in conjunction with the second edition of IEC 61439-1. The provisions of the general rules dealt with in IEC 61439-1 (hereinafter referred to as Part 1) are only applicable to this standard insofar as they are specifically cited. When this

39、 standard states “addition”, “modification” or “replacement”, the relevant text in Part 1 is to be adapted accordingly. Subclauses that are numbered with a 101 (102, 103 etc.) suffix are additional to the same subclause in Part 1. Tables and figures in this Part 6 that are new are numbered starting

40、with 101. New annexes in this Part 6 are lettered AA, BB, etc. The “in some countries” notes regarding differing national practices are contained in the following subclauses: 5.4 A list of all parts of the IEC 61439 series, under the general title Low-voltage switchgear and controlgear assemblies ca

41、n be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed

42、, withdrawn, replaced by a revised edition, or amended. 61439-6 IEC:2012 5 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES Part 6: Busbar trunking systems (busways) 1 Scope NOTE 1 Throughout this part, the abbreviation BTS is used for a busbar trunking system. Where reference to Part 1 is made, th

43、e term ASSEMBLY therefore reads as “BTS”. This part of IEC 61439 lays down the definitions and states the service conditions, construction requirements, technical characteristics and verification requirements for low voltage BTS (see 3.101) as follows: BTS for which the rated voltage does not exceed

44、 1 000 V in case of a.c. or 1 500 V in case of d.c.; BTS intended for use in connection with the generation, transmission, distribution and conversion of electric energy, and for the control of electric energy consuming equipment; BTS designed for use under special service conditions, for example in

45、 ships, in rail vehicles, and for domestic applications (operated by unskilled persons), provided that the relevant specific requirements are complied with; NOTE 2 Supplementary requirements for BTS in ships are covered by IEC 60092-302. BTS designed for electrical equipment of machines. Supplementa

46、ry requirements for BTS forming part of a machine are covered by the IEC 60204 series. This standard applies to all BTS whether they are designed, manufactured and verified on a one-off basis or fully standardized and manufactured in quantity. The manufacture and/or assembly may be carried out by a

47、manufacturer other than the original manufacturer (see 3.10.1 and 3.10.2 of Part 1). This standard does not apply to individual devices and self-contained components, such as motor starters, fuse switches, electronic equipment, etc. which will comply with the relevant product standard. This standard

48、 does not apply to the specific types of ASSEMBLIES covered by other parts of the IEC 61439 series, to supply track systems in accordance with IEC 60570, to cable trunking and ducting systems in accordance with the IEC 61084 series, nor to power track systems in accordance with the IEC 61534 series.

49、 2 Normative references This clause of Part 1 is applicable except as follows. Addition: IEC 60332-3-10:2000, Tests on electric and optical fibre cables under fire conditions Part 3-10: Test for vertical flame spread of vertically-mounted bunched wires or cables Apparatus IEC 60439-2:2000, Low-voltage switchgear and controlgear assemblies Part 2: Particular requirements for busbar trunking systems (busw