IEC 61337-1-2004 Filters using waveguide type dielectric resonators - Part 1 Generic specification《采用波导型介电谐振器的滤波器.第1部分 通用规范》.pdf

《IEC 61337-1-2004 Filters using waveguide type dielectric resonators - Part 1 Generic specification《采用波导型介电谐振器的滤波器.第1部分 通用规范》.pdf》由会员分享，可在线阅读，更多相关《IEC 61337-1-2004 Filters using waveguide type dielectric resonators - Part 1 Generic specification《采用波导型介电谐振器的滤波器.第1部分 通用规范》.pdf（54页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 61337-1 Edition 1.0 2004-11 INTERNATIONAL STANDARD NORME INTERNATIONALE Filters using waveguide type dielectric resonators Part 1: Generic specification Filtres utilisant des rsonateurs dilectriques modes guids Partie 1: Spcification gnrique IEC 61337-1:2004 THIS PUBLICATION IS COPYRIGHT PROTEC

2、TED Copyright 2004 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs me

3、mber National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproductio

4、n rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du deman

5、deur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +

6、41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications

7、 The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Useful links: IEC publications search - www.iec.ch/searchpub The advanced search enables you to find IEC pub

8、lications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications r

9、eleased. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as

10、 the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. A propos de la CEI La Commission Electrotechnique In

11、ternationale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous

12、assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub La recherche avance vous permet de trouver des publications CEI en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,)

13、. Elle donne aussi des informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications de la CEI. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par

14、 mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire

15、Electrotechnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 61337-1 Edition 1.0 2004-11 INTERNATIONAL STANDARD NORME INTERNATIONALE Filters using wa

16、veguide type dielectric resonators Part 1: Generic specification Filtres utilisant des rsonateurs dilectriques modes guids Partie 1: Spcification gnrique INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE T ICS 31.140 PRICE CODE CODE PRIX ISBN 978-2-8322-0999-8 Regi

17、stered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distrib

18、uteur agr. 2 61337-1 IEC:2004 CONTENTS FOREWORD . 3 1 General 5 1.1 Scope 5 1.2 Normative references 5 1.3 Order of precedence . 6 2 Terminology and general requirements . 6 2.1 General . 6 2.2 Terms and definitions 6 2.3 Preferred ratings and characteristics . 13 2.4 Marking . 14 3 Quality assessme

19、nt procedures 14 3.1 Primary stage of manufacture 14 3.2 Structurally similar components . 14 3.3 Sub-contracting . 14 3.4 Incorporated components 14 3.5 Manufacturers approval 14 3.6 Approval procedures . 14 3.7 Procedures for capability approval 15 3.8 Procedures for qualification approval . 16 3.

20、9 Test procedures 16 3.10 Screening requirements 16 3.11 Rework and repair work . 16 3.12 Certified records of released lots . 16 3.13 Validity of release 17 3.14 Release for delivery 17 3.15 Unchecked parameters 17 4 Test and measurement procedures . 17 4.1 General . 17 4.2 Test and measurement con

21、ditions . 17 4.3 Visual inspection . 18 4.4 Dimensions and gauging procedures . 18 4.5 Electrical test procedures 18 4.6 Mechanical and environmental test procedures . 22 Figure 1 Equivalent circuit 7 Figure 2 Typical frequency characteristics of a band-pass filter . 10 Figure 3 Typical frequency ch

22、aracteristics of a band-stop filter 11 Figure 4 Insertion attenuation and group delay measurement 20 Figure 5 Return attenuation measurement . 20 61337-1 IEC:2004 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ FILTERS USING WAVEGUIDE TYPE DIELECTRIC RESONATORS Part 1: Generic specification FOREWORD 1

23、) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrica

24、l and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technica

25、l committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organiza

26、tion for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical co

27、mmittee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications

28、 is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national an

29、d regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in co

30、nformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for

31、 any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Norm

32、ative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held respo

33、nsible for identifying any or all such patent rights. International Standard IEC 61337-1 has been prepared by IEC technical committee 49: Piezoelectric and dielectric devices for frequency control and selection. This part of IEC 61337 cancels and replaces IEC 61337-1-1:1995 and IEC 61337-1-2:1999. T

34、his bilingual version (2013-08) corresponds to the monolingual English version, published in 2004-11. The text of this standard is based on the following documents: FDIS Report on voting 49/685/FDIS 49/695/RVD Full information on the voting for the approval of this standard can be found in the repor

35、t on voting indicated in the above table. 4 61337-1 IEC:2004 The French version of this standard has not been voted upon. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. IEC 61337 consists of the following parts, under the general title Filters using waveguide ty

36、pe dielectric resonators: Part 1: Generic specification Part 2: Guidance for use The committee has decided that the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific pub

37、lication. At this date, the publication will be reconfirmed; withdrawn; replaced by a revised edition, or amended. 61337-1 IEC:2004 5 FILTERS USING WAVEGUIDE TYPE DIELECTRIC RESONATORS Part 1: Generic specification 1 General 1.1 Scope This part of IEC 61337 applies to filters using waveguide type di

38、electric resonators of assessed quality using either capability approval or qualification approval procedures. It also lists the test and measurement procedures which may be selected for use in detail specifications for such filters. 1.2 Normative references The following referenced documents are in

39、dispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60027 (all parts), Letter symbols to be used in electrical technology IEC 60050(561):1

40、991, International Electrotechnical Vocabulary (IEV) Chapter 561: Piezo- electric devices for frequency control and selection IEC 60068-1:1988, Environmental testing Part 1: General and guidance IEC 60068-2-1:1990, Environmental testing Part 2: Tests Test A: Cold IEC 60068-2-2:1974, Environmental te

41、sting Part 2: Tests Test B: Dry Heat IEC 60068-2-6:1995, Environmental testing Part 2: Tests Test Fc: Vibration (sinusoidal) IEC 60068-2-7:1983, Environmental testing Part 2: Tests Test Ga: Acceleration, steady state IEC 60068-2-13:1983, Environmental testing Part 2: Tests Test M: Low air pressure I

42、EC 60068-2-14:1984, Environmental testing Part 2: Tests Test N: Change of temperature IEC 60068-2-20:1979, Environmental testing Part 2: Tests Test T: Soldering IEC 60068-2-21:1999, Environmental testing Part 2-21: Tests Test U: Robustness of terminations and integral mounting devices IEC 60068-2-27

43、:1987, Environmental testing Part 2: Tests Test Ea and guidance: Shock IEC 60068-2-29:1987, Environmental testing Part 2: Tests Test Eb and guidance: Bump IEC 60068-2-30:1980, Environmental testing Part 2: Tests Test Db and guidance: Damp heat, cyclic (12 + 12 hour cycle) 6 61337-1 IEC:2004 IEC 6006

44、8-2-58:1999, Environmental testing Part 2-58: Tests Tests Td: Test methods for solderability, resistance to dissolution of metalization and to soldering heat of surface mounting devices (SMD) IEC 60068-2-78:2001, Environmental testing Part 2-78: Tests Test Cab: Damp heat, steady state IEC 60617 (all

45、 parts) DB 1 , Graphical symbols for diagrams QC 001001:2000, IEC Quality Assessment System for Electronic Components (IECQ) Basic Rules QC 001002-2:1998, IEC Quality Assessment System for Electronic Components (IECQ) Rules of Procedure Part 2: Documentation QC 001002-3:1998, IEC Quality Assessment

46、System for Electronic Components (IECQ) Rules of Procedure Part 3: Approval Procedures QC 001005:2000, Register of Firms, Products and Services approved under the IECQ System, including ISO 9000 ISO 1000:1992, SI units and recommendation for the use of their multiples and of certain other units 1.3

47、Order of precedence Where any discrepancies occur for any reason, documents shall rank in the following order of authority: detail specification; sectional specification; generic specification; any other international documents (for example, of the IEC) to which reference is made. The same order of

48、precedence shall apply to equivalent national documents. 2 Terminology and general requirements 2.1 General Units, graphical symbols, letter symbols and terminology shall whenever possible, be taken from IEC 60617, IEC 60027, IEC 60050(561) and ISO 1000. Any other units, symbols and terminology pecu

49、liar to one of the components covered by the Generic Specification, shall be taken from the relevant IEC or ISO documents listed under 1.2. 2.2 Terms and definitions For the purposes of this part of IEC 61337, the following terms and definitions apply. Further detailed information may be provided in IEC 61994-1 for some of the following terms. _ 1