IEC 61196-1-1-2007 Coaxial communication cables - Part 1-1 Capability approval for coaxial communication cables《同轴通信电缆.第1-1部分 同轴通信电缆的能力鉴定》.pdf

《IEC 61196-1-1-2007 Coaxial communication cables - Part 1-1 Capability approval for coaxial communication cables《同轴通信电缆.第1-1部分 同轴通信电缆的能力鉴定》.pdf》由会员分享，可在线阅读，更多相关《IEC 61196-1-1-2007 Coaxial communication cables - Part 1-1 Capability approval for coaxial communication cables《同轴通信电缆.第1-1部分 同轴通信电缆的能力鉴定》.pdf（24页珍藏版）》请在麦多课文档分享上搜索。

1、 INTERNATIONAL STANDARD IECCEINORME INTERNATIONALE61196-1-1First editionPremire dition2007-04Coaxial communication cables Part 1-1: Capability approval for coaxial cables Cbles coaxiaux de communication Partie 1-1: Agrment de savoir-faire pour cbles coaxiaux Reference number Numro de rfrence IEC/CEI

2、 61196-1-1:2007 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2007 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, with

3、out permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Comm

4、ittee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la

5、 CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central O

6、ffice 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. A

7、bout IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables y

8、ou to search by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month all n

9、ew publications released. Available on-line and also by email. Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 1

10、1 Fax: +41 22 919 03 00 A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le conte

11、nu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue en-ligne de la CEI vous permet deffectue

12、r des recherches en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Il donne aussi des informations sur les projets et les publications retires ou remplaces. Just Published CEI: www.iec.ch/online_news/justpub Restez inform sur les nouvelles publications de la CEI. Just Publishe

13、d dtaille deux fois par mois les nouvelles publications parues. Disponible en-ligne et aussi par email. Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du Service client

14、s ou contactez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 INTERNATIONAL STANDARD IECCEINORME INTERNATIONALE61196-1-1First editionPremire dition2007-04Coaxial communication cables Part 1-1: Capability approval for coaxial cables Cbles coaxiaux de communication Partie 1-1: Agrm

15、ent de savoir-faire pour cbles coaxiaux For price, see current cataloguePour prix, voir catalogue en vigueur PRICE CODE CODE PRIX L Commission Electrotechnique InternationaleInternational Electrotechnical Commission 2 61196-1-1 IEC:2007 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ COAXIAL COMMUNICATI

16、ON CABLES Part 1-1: Capability approval for coaxial cables FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-o

17、peration on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to

18、 as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this p

19、reparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international c

20、onsensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable effor

21、ts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publicatio

22、ns transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and c

23、annot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and

24、 members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publicat

25、ion or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publicat

26、ion may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61196-1-1 has been prepared by subcommittee 46A: Coaxial cables, of IEC technical committee 46: Cables, wires, waveguides, r.f. connectors, r.f. and mi

27、crowave passive components and accessories. The text of this standard is based on the following documents: FDIS Report on voting 46A/779/FDIS 46A/791/RVDFull information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publicatio

28、n has been drafted in accordance with the ISO/IEC Directives, Part 2. 61196-1-1 IEC:2007 3 This part of IEC 61196 is one of a series of standards being developed for coaxial communication cables. The series will comprise the following parts: Part 1: Generic specification General, definitions and req

29、uirements Part 1-1: Capability approval for coaxial cables Part 1-1XX: Electrical test methods Part 1-2XX: Environmental test methods Part 1-3XX: Mechanical test methods Part 1-4XX: Electromagnetic compatibility test methods Part 4: Sectional specification for radiating cables Part 5: Sectional spec

30、ification for CATV trunk and distribution cables Part 5-1: Blank detail specification for CATV trunk distribution cables Part 6: Sectional specification for drop cables Part 6-1: Blank detail specification for CATV drop cables The committee has decided that the contents of this publication will rema

31、in unchanged until the maintenance result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed; withdrawn; replaced by a revised edition, or amended. 4 61196-1-1 IEC:2007 INTRODUCTION Quali

32、ty systems are intended to give confidence to the customers. It is presumed that a supplier whose full organization complies with ISO 9000 is able to assess the quality of his services (services can be a product). However, to assess the quality of the services is obviously not sufficient from a cust

33、omer point of view. The customers concern is the quality of the product. That means the compliance to a given specification. The IEC Quality Assessment System for Electronic Components (IECQ) product/process approval procedures Qualification Approval (QA), Capability Approval (CA) and Technology App

34、roval (TA) are intended to ensure that all products delivered under one of them will comply to a given specification. These procedures are described in QC 001002-3. As a first step, to achieve this task, the three procedures just mentioned require as a prerequisite the manufacturers approval (descri

35、bed in Clause 2 of QC 001002-3 and which is basically an ISO 9000 approval with the relevant technical scope, plus IECQ requirements as defined in 2.3.2 of QC 001002-3). Manufacturers Approval ensures that all the actions taken for QA, CA or TA will be under control and well documented. The second s

36、tep is the qualifying stage, which is sometimes called type Approval. In case of Qualification Approval (QA), the purpose of this stage is to demonstrate the validity of the design file of a given product. (Ideally, the design file should contain the process and the control files). In case of Capabi

37、lity Approval (CA) or Technology Approval (TA), this stage is intended to demonstrate the ability of the supplier to design, manufacture, control and supply any product within declared boundaries. The third step is the maintainability of the approval. In case of Qualification Approval, it is based o

38、n final tests, lot by lot tests and periodic tests. These tests achieved on final products are intended to demonstrate that there is not any major deviation from the characteristics of the delivered product. They are independent of the eventual deviation of the process manufacture. In case of Capabi

39、lity or Technology Approval, this third step is based on the observation of the process by itself. The Capability Approval policy is based on the relationship which exists between each step of the process and the characteristics of a capability qualifying component (CQC), which may be specially desi

40、gned for this purpose, or taken from production. The tests achieved on these CQC are intended to demonstrate that the process does not deviate and therefore that the final product will be in the expected limits. The Technology Approval assumes that the assessment of the process line parameters is su

41、fficient to guarantee that the final product will be in the expected limits. The advantage of TA and CA comes from the assumption that all the relationships between the deviation of each parameter all along the process line are well known and controlled. This assumption is not wrong if the different

42、 steps of manufacture are independent (electronic components as discrete devices), but for the cable manufacture, these steps are interdependent and the influence on the final product of any deviation of any parameters is not obvious. Therefore, though the TA certainly brings some improvement to CA,

43、 the approval for communication cables should be based on CA in that it uses CQCs to ensure that the process does not deviate. These CQCs should, together, cover the full technology within the declared limits. 61196-1-1 IEC:2007 5 COAXIAL COMMUNICATION CABLES Part 1-1: Capability approval for coaxia

44、l cables 1 Scope This International standard applies to Capability Approval requirements for coaxial communi-cation cables as specified in generic specification IEC 61196-1. It specifies the requirements for a manufacturer seeking approval of his capability to design (if applicable), manufacture, in

45、spect, test and release coaxial communication cables as defined in his capability manual. Manufacturers Approval, which embodies all the relevant requirements of ISO 9001, is a prerequisite for granting Capability Approval but a manufacturer may apply for Manufacturers Approval and Capability Approv

46、al concurrently. NOTE 1 This document was written in order to be used in case of third party certification; however, it may be used as the basis for second party or self certification. NOTE 2 When certification is required, CA should be used according to the following. CA may also be used for second

47、 party or self-assessment. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.

48、 IEC 60027 (all parts), Letter symbols to be used in electrical technology IEC 60050 (all parts), International Electrotechnical vocabulary IEC 60617-DB:20011), Graphical symbols for diagrams IEC 61196-1, Coaxial communication cables Part 1: Generic specification General, definitions and requirement

49、s ISO 1000, SI Units and recommendations for the use of their multiples and of certain other units ISO 9000, Quality management systems Fundamentals and vocabulary ISO 9001, Quality management systems Requirements IECQ 001002-3:1998, IEC Quality Assessment System for Electronic Components (IECQ) Rules of Procedure. Part 3: Approval procedures 1)“DB” refers to the IEC on-line databas