IEC 61158-5-8-2007 Industrial communication networks - Fieldbus specifications - Part 5-8 Application layer service definition - Type 8 elements《工业通讯网络.数据总线规范.第5-8部分 应用层设备定义.8型元件》.pdf

《IEC 61158-5-8-2007 Industrial communication networks - Fieldbus specifications - Part 5-8 Application layer service definition - Type 8 elements《工业通讯网络.数据总线规范.第5-8部分 应用层设备定义.8型元件》.pdf》由会员分享，可在线阅读，更多相关《IEC 61158-5-8-2007 Industrial communication networks - Fieldbus specifications - Part 5-8 Application layer service definition - Type 8 elements《工业通讯网络.数据总线规范.第5-8部分 应用层设备定义.8型元件》.pdf（98页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 61158-5-8 Edition 1.0 2007-12 INTERNATIONAL STANDARD Industrial communication networks Fieldbus specifications Part 5-8: Application layer service definition Type 8 elements IEC 61158-5-8:2007(E) THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2007 IEC, Geneva, Switzerland All rights reserved

2、. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you

3、 have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.c

4、h Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept

5、 under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technica

6、l committee,). It also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available on-line and also by email. Electrop

7、edia: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary online. Customer Serv

8、ice Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC 61158-5-8 Edition 1.0 2007-12 INTERNATIONAL STAN

9、DARD Industrial communication networks Fieldbus specifications Part 5-8: Application layer service definition Type 8 elements INTERNATIONAL ELECTROTECHNICAL COMMISSION XD ICS 35.100.70; 25.040.40 PRICE CODE ISBN 2-8318-9456-5 2 61158-5-8 IEC:2007(E) CONTENTS FOREWORD.4 INTRODUCTION.6 1 Scope.7 1.1 O

10、verview.7 1.2 Specifications8 1.3 Conformance.8 2 Normative references .8 3 Terms and definitions .9 3.1 ISO/IEC 7498-1 terms .9 3.2 ISO/IEC 8822 terms 9 3.3 ISO/IEC 9545 terms 9 3.4 ISO/IEC 8824 terms 9 3.5 Fieldbus data-link layer terms9 3.6 Fieldbus application layer specific definitions 10 3.7 A

11、bbreviations and symbols16 3.8 Conventions 16 4 Concepts20 4.1 Overview.20 4.2 Architectural relationships .20 4.3 Fieldbus Application Layer structure22 4.4 FAL naming and addressing 32 4.5 Architecture summary33 4.6 FAL service procedures.33 4.7 Notional FAL service procedures INFORMATIVE.33 4.8 C

12、ommon FAL attributes.34 4.9 Common FAL service parameters35 4.10 APDU size.36 5 Data type ASE36 5.1 General .36 5.2 Formal definition of data type objects 38 5.3 FAL defined data types38 5.4 Data type ASE service specification 42 6 Communication model specification42 6.1 ASEs.42 6.2 ARs.85 6.3 Summa

13、ry of FAL classes.91 6.4 Permitted FAL services by AREP role91 Bibliography93 Figure 1 Relationship to the OSI basic reference model.20 Figure 2 Architectural positioning of the Type 8 FAL 21 Figure 3 Client/server interactions .23 Figure 4 Push model interactions.24 Figure 5 APOs services conveyed

14、by the FAL25 Figure 6 Application entity structure.27 61158-5-8 IEC:2007(E) 3 Figure 7 Example FAL ASEs28 Figure 8 FAL management of objects.29 Figure 9 ASE service conveyance30 Figure 10 Defined and established AREPs.32 Figure 11 FAL architectural components 33 Figure 12 Data type class hierarchy e

15、xample.36 Figure 13 The AR ASE conveys APDUs between APs58 Figure 14 1-to-1 AR establishment.65 Table 1 Get attributes service parameters43 Table 2 Identify50 Table 3 Get status .51 Table 4 Initiate.53 Table 5 Terminate55 Table 6 Reject .57 Table 7 Conveyance of service primitives by AREP role 59 Ta

16、ble 8 Valid combinations of AREP roles involved in an AR .59 Table 9 AR-unconfirmed send63 Table 10 AR-establish service64 Table 11 Valid combinations of AREP classes to be related.66 Table 12 AR-abort .67 Table 13 AR-Data-Send-Acknowledge service parameters.68 Table 14 Read service parameters.73 Ta

17、ble 15 Write service parameters.74 Table 16 Information report service75 Table 17 Start service parameters .79 Table 18 Stop service parameters80 Table 19 Resume service parameters 81 Table 20 Reset service parameters82 Table 21 State transitions for a function invocation object84 Table 22 FAL class

18、 summary.91 Table 23 Services by AREP role 92 4 61158-5-8 IEC:2007(E) INTERNATIONAL ELECTROTECHNICAL COMMISSION _ INDUSTRIAL COMMUNICATION NETWORKS FIELDBUS SPECIFICATIONS Part 5-8: Application layer service definition Type 8 elements FOREWORD 1) The International Electrotechnical Commission (IEC) i

19、s a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to

20、 other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in

21、the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with condi

22、tions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC Nati

23、onal Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the wa

24、y in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC

25、 Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should e

26、nsure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage o

27、f any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the

28、referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. N

29、OTE Use of some of the associated protocol types is restricted by their intellectual-property-right holders. In all cases, the commitment to limited release of intellectual-property-rights made by the holders of those rights permits a particular data-link layer protocol type to be used with physical

30、 layer and application layer protocols in Type combinations as specified explicitly in the IEC 61784 series. Use of the various protocol types in other combinations may require permission from their respective intellectual-property-right holders. International Standard IEC 61158-5-8 has been prepare

31、d by subcommittee 65C: Industrial networks, of IEC technical committee 65: Industrial-process measurement, control and automation. This first edition and its companion parts of the IEC 61158-5 subseries cancel and replace IEC 61158-5:2003. This edition of this part constitutes a technical revision.

32、This edition of IEC 61158-5 includes the following significant changes from the previous edition: a) deletion of the former Type 6 fieldbus for lack of market relevance; b) addition of new types of fieldbuses; c) partition of part 5 of the third edition into multiple parts numbered -5-2, -5-3, 61158

33、-5-8 IEC:2007(E) 5 The text of this standard is based on the following documents: FDIS Report on voting 65C/475/FDIS 65C/486/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in ac

34、cordance with ISO/IEC Directives, Part 2. The committee has decided that the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC web site under http:/webstore.iec.ch in the data related to the specific publication. At this date, the publication w

35、ill be: reconfirmed; withdrawn; replaced by a revised edition, or amended. NOTE The revision of this standard will be synchronized with the other parts of the IEC 61158 series. The list of all the parts of the IEC 61158 series, under the general title Industrial communication networks Fieldbus speci

36、fications, can be found on the IEC web site. 6 61158-5-8 IEC:2007(E) INTRODUCTION This part of IEC 61158 is one of a series produced to facilitate the interconnection of automation system components. It is related to other standards in the set as defined by the “three-layer” fieldbus reference model

37、 described in IEC/TR 61158-1. The application service is provided by the application protocol making use of the services available from the data-link or other immediately lower layer. This standard defines the application service characteristics that fieldbus applications and/or system management ma

38、y exploit. Throughout the set of fieldbus standards, the term “service” refers to the abstract capability provided by one layer of the OSI Basic Reference Model to the layer immediately above. Thus, the application layer service defined in this standard is a conceptual architectural service, indepen

39、dent of administrative and implementation divisions. 61158-5-8 IEC:2007(E) 7 INDUSTRIAL COMMUNICATION NETWORKS FIELDBUS SPECIFICATIONS Part 5-8: Application layer service definition Type 8 elements 1 Scope 1.1 Overview The fieldbus application layer (FAL) provides user programs with a means to acces

40、s the fieldbus communication environment. In this respect, the FAL can be viewed as a “window between corresponding application programs.” This standard provides common elements for basic time-critical and non-time-critical messaging communications between application programs in an automation envir

41、onment and material specific to Type 8 fieldbus. The term “time-critical” is used to represent the presence of a time-window, within which one or more specified actions are required to be completed with some defined level of certainty. Failure to complete specified actions within the time window ris

42、ks failure of the applications requesting the actions, with attendant risk to equipment, plant and possibly human life. This standard defines in an abstract way the externally visible service provided by the Type 8 fieldbus application layer in terms of a) an abstract model for defining application

43、resources (objects) capable of being manipulated by users via the use of the FAL service, b) the primitive actions and events of the service; c) the parameters associated with each primitive action and event, and the form which they take; and d) the interrelationship between these actions and events

44、, and their valid sequences. The purpose of this standard is to define the services provided to 1) the FAL user at the boundary between the user and the application layer of the fieldbus reference model, and 2) Systems Management at the boundary between the application layer and Systems Management o

45、f the fieldbus reference model. This standard specifies the structure and services of the Type 8 fieldbus application layer, in conformance with the OSI Basic Reference Model (ISO/IEC 7498) and the OSI application layer structure (ISO/IEC 9545). FAL services and protocols are provided by FAL applica

46、tion-entities (AE) contained within the application processes. The FAL AE is composed of a set of object-oriented application service elements (ASEs) and a layer management entity (LME) that manages the AE. The ASEs provide communication services that operate on a set of related application process

47、object (APO) classes. One of the FAL ASEs is a management ASE that provides a common set of services for the management of the instances of FAL classes. Although these services specify, from the perspective of applications, how request and responses are issued and delivered, they do not include a sp

48、ecification of what the requesting and responding applications are to do with them. That is, the behavioral aspects of the applications are not specified; only a definition of what requests and responses they can send/receive is specified. This permits greater flexibility to the FAL users in standar

49、dizing 8 61158-5-8 IEC:2007(E) such object behavior. In addition to these services, some supporting services are also defined in this standard to provide access to the FAL to control certain aspects of its operation. 1.2 Specifications The principal objective of this standard is to specify the characteristics of conceptual application layer services suitable for time-critical communications, and thus supplement