IEC 60947-7-2-2009 Low-voltage switchgear and controlgear - Part 7-2 Ancillary equipment - Protective conductor terminal blocks for copper conductors《低压开关设备和控制设备.第7-2部分 辅助设备.铜导线用接线板的防护导线》.pdf

《IEC 60947-7-2-2009 Low-voltage switchgear and controlgear - Part 7-2 Ancillary equipment - Protective conductor terminal blocks for copper conductors《低压开关设备和控制设备.第7-2部分 辅助设备.铜导线用接线板的防护导线》.pdf》由会员分享，可在线阅读，更多相关《IEC 60947-7-2-2009 Low-voltage switchgear and controlgear - Part 7-2 Ancillary equipment - Protective conductor terminal blocks for copper conductors《低压开关设备和控制设备.第7-2部分 辅助设备.铜导线用接线板的防护导线》.pdf（42页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 60947-7-2Edition 3.0 2009-04INTERNATIONAL STANDARD NORME INTERNATIONALELow-voltage switchgear and controlgear Part 7-2: Ancillary equipment Protective conductor terminal blocks for copper conductors Appareillage basse tension Partie 7-2: Matriels accessoires Blocs de jonction de conducteur de p

2、rotection pour conducteurs en cuivre IEC60947-7-2:2009 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2009 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, inc

3、luding photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below

4、 or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et

5、les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI d

6、e votre pays de rsidence. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical,

7、 electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/search

8、pub The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Jus

9、t Published details twice a month all new publications released. Available on-line and also by email. Electropedia: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent te

10、rms in additional languages. Also known as the International Electrotechnical Vocabulary online. Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Emai

11、l: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A pr

12、opos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue en-lig

13、ne de la CEI vous permet deffectuer des recherches en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Il donne aussi des informations sur les projets et les publications retires ou remplaces. Just Published CEI: www.iec.ch/online_news/justpub Restez inform sur les nouvelles pub

14、lications de la CEI. Just Published dtaille deux fois par mois les nouvelles publications parues. Disponible en-ligne et aussi par email. Electropedia: www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 20 000 termes et dfinitions

15、 en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International en ligne. Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette publication ou si

16、vous avez des questions, visitez le FAQ du Service clients ou contactez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC 60947-7-2Edition 3.0 2009-04INTERNATIONAL STANDARD NORME INTERNATIONALELow-voltage switchgear and controlgear Part 7-2: Ancillary equipment Protective conduc

17、tor terminal blocks for copper conductors Appareillage basse tension Partie 7-2: Matriels accessoires Blocs de jonction de conducteur de protection pour conducteurs en cuivre INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE RICS 29.120.99; 29.130.20 PRICE CODECODE

18、 PRIXISBN 2-8318-1038-1 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale 2 60947-7-2 IEC:2009 CONTENTS FOREWORD.4 1 General 6 1.1 Scope6 1.2 Normative references 6 2 Definitions 7 3 Classification7 4 Characteristics .

19、7 4.1 Summary of characteristics .7 4.2 Type of protective conductor terminal block.7 4.3 Rated and limiting values 8 4.3.1 Void.8 4.3.2 Short-time withstand current8 4.3.3 Standard cross-sections 8 4.3.4 Rated cross-section.8 4.3.5 Rated connecting capacity.8 5 Product information 8 5.1 Marking .8

20、5.2 Additional information9 6 Normal service, mounting and transport conditions.9 7 Constructional and performance requirements9 7.1 Constructional requirements9 7.1.1 Clamping units.9 7.1.2 Connection of support .9 7.1.3 Clearance and creepage distances9 7.1.4 Terminal block identification and mark

21、ing 10 7.1.5 Resistance to abnormal heat and fire.10 7.1.6 Rated cross-section and rated connecting capacity .10 7.1.7 Protective conductor mounting rails .10 7.2 Performance requirements 10 7.2.1 Temperature rise .10 7.2.2 Dielectric properties.10 7.2.3 Short-time withstand current10 7.2.4 Voltage

22、drop10 7.2.5 Electrical performance after ageing (for screwless-type protective conductor terminal blocks only) .11 7.3 Electromagnetic compatibility (EMC) .11 8 Tests 11 8.1 Kinds of test 11 8.2 General .11 8.3 Verification of mechanical characteristics 11 8.4 Verification of electrical characteris

23、tics11 8.4.1 General .11 8.4.2 Void.12 8.4.3 Dielectric tests.12 8.4.4 Verification of the voltage drop 13 8.4.5 Temperature-rise test 14 60947-7-2 IEC:2009 3 8.4.6 Short-time withstand current test .15 8.4.7 Ageing test (for screwless-type terminal blocks only).16 8.5 Verification of thermal charac

24、teristics 17 8.6 Verification of EMC characteristics 17 Annex A (normative) Maximum short-time withstand currents allocated to the rail profile and thermal rated current of a PEN busbar .18 Figure 1 Arrangement for the dielectric test .12 Figure 2 Arrangement for the voltage drop test 13 Figure 3 Ar

25、rangement for the temperature-rise test for test group a) 15 Figure 4 Arrangement for the temperature-rise test for test group b) 15 Figure 5 Arrangement for the thermal short-time withstand current test16 Table 1 Relationship between rated cross-section and rated connecting capacity of protective c

26、onductor terminal blocks .8 Table A.1 Maximum short-time withstand currents allocated to the rail profile and thermal rated current of a PEN busbar18 4 60947-7-2 IEC:2009 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR Part 7-2: Ancillary equipment Protective condu

27、ctor terminal blocks for copper conductors FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all

28、questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publica

29、tion(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC

30、collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opin

31、ion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to e

32、nsure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently

33、 to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendere

34、d responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its

35、technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other

36、 IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the s

37、ubject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60947-7-2 has been prepared by subcommittee 17B: Low-voltage switchgear and controlgear, of IEC technical committee 17: Switchgear and controlgear. This third edition

38、of IEC 60947-7-2 cancels and replaces the second edition, published in 2002, and constitutes a technical revision. The main technical modifications of this standard since this previous publication are listed below: requirements for tightening torques for the tests improved and referenced to Table 4

39、of IEC 60947-1, Annex B deleted; the wording of the short-time withstand current test improved in 8.4.6. 60947-7-2 IEC:2009 5 This standard shall be read in conjunction with IEC 60947-1 and IEC 60947-7-1. The provisions of the general rules dealt with in IEC 60947-1 and the requirements for terminal

40、 blocks of IEC 60947-7-1 are applicable to this standard, where specifically called for. Clauses and subclauses, tables, figures and annexes thus applicable are identified by reference to IEC 60947-1 or IEC 60947-7-1, e.g. 1.2 of IEC 60947-1, Table 4 of IEC 60947-7-1 or Annex A of IEC 60947-1. The t

41、ext of this standard is based on the following documents: FDIS Report on voting 17B/1655/FDIS 17B/1669/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/

42、IEC Directives, Part 2. A list of all the parts in the IEC 60947 series, under the general title Low-voltage switchgear and controlgear, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the maintenance result date indicated

43、on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. 6 60947-7-2 IEC:2009 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR Part 7-2: Ancillary equipment Protec

44、tive conductor terminal blocks for copper conductors 1 General 1.1 Scope This part of IEC 60947 specifies requirements for protective conductor terminal blocks with PE function up to 120 mm2(250 kcmil) and for protective conductor terminal blocks with PEN function equal to and above 10 mm2(AWG 8) wi

45、th screw-type or screwless-type clamping units, primarily intended for industrial applications. NOTE AWG is the abbreviation of “American Wire Gage” Gage (US) = Gauge (UK) kcmil = 1 000 cmil 1 cmil = 1 circular mil = surface of a circle having a diameter of 1 mil 1 mil = 1/1 000 inch Protective cond

46、uctor terminal blocks are used to form the electrical and mechanical connection between copper conductors and the fixing support. lt is applicable to protective conductor terminal blocks for the connection of round copper conductors with or without special preparation having a cross-section between

47、0,2 mm2and 120 mm2(AWG 24 and 250 kcmil), intended to be used in circuits of a rated voltage not exceeding 1 000 V a.c. up to 1 000 Hz or 1 500 V d.c., most commonly in conjunction with terminal blocks according to IEC 60947-7-1. This standard may be used as guide for protective conductor terminal b

48、locks requiring the fixing of special devices to the conductors, for example quick connect terminations or wrapped connections, etc.; protective conductor terminal blocks providing direct contact to the conductors by means of edges or points penetrating the insulation, for example insulation displac

49、ement connections, etc. Where applicable in this standard, the term “clamping unit” has been used instead of the term “terminal”. This is taken into account in case of reference to IEC 60947-1. 1.2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest