IEC 60869-1-2012 Fibre optic interconnecting devices and passive components - Fibre optic passive power control devices - Part 1 Generic specification《光纤互连设备和无源组件.光纤无源功率控制装置.第1部分 总规范》.pdf

《IEC 60869-1-2012 Fibre optic interconnecting devices and passive components - Fibre optic passive power control devices - Part 1 Generic specification《光纤互连设备和无源组件.光纤无源功率控制装置.第1部分 总规范》.pdf》由会员分享，可在线阅读，更多相关《IEC 60869-1-2012 Fibre optic interconnecting devices and passive components - Fibre optic passive power control devices - Part 1 Generic specification《光纤互连设备和无源组件.光纤无源功率控制装置.第1部分 总规范》.pdf（74页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 60869-1 Edition 4.0 2012-12 INTERNATIONAL STANDARD NORME INTERNATIONALE Fibre optic interconecting devices and passive components Fibre optic passive power control devices Part 1: Generic specification Dispositifs dinterconnexion et composants passifs fibres optiques Dispositifs fibres optiques

2、 passifs de contrle de la puissance Partie 1: Spcification gnrique IEC60869-1:2012 colourinsideTHIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2012 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by

3、any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publi

4、cation, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique

5、ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou

6、 contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization

7、that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment migh

8、t have been published. Useful links: IEC publications search - www.iec.ch/searchpub The advanced search enables you to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just P

9、ublished - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms co

10、ntaining more than 30 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or n

11、eed further assistance, please contact the Customer Service Centre: csciec.ch. A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technolo

12、gies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub La r

13、echerche avance vous permet de trouver des publications CEI en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform sur les no

14、uvelles publications de la CEI. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 termes et

15、 dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez de

16、s questions contactez-nous: csciec.ch. IEC 60869-1 Edition 4.0 2012-12 INTERNATIONAL STANDARD NORME INTERNATIONALE Fibre optic interconecting devices and passive components Fibre optic passive power control devices Part 1: Generic specification Dispositifs dinterconnexion et composants passifs fibre

17、s optiques Dispositifs fibres optiques passifs de contrle de la puissance Partie 1: Spcification gnrique INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE V ICS 33.180.20 PRICE CODE CODE PRIX ISBN 978-2-83220-544-0 Registered trademark of the International Electrot

18、echnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. colourinside 2 60869-1 IEC:2012 CON

19、TENTS FOREWORD . 4 1 Scope . 6 2 Normative references . 6 3 Terms and definitions . 7 3.1 Basic terms . 7 3.2 Component terms 7 3.3 Performance terms 8 4 Description of devices 9 4.1 Optical attenuator 9 4.2 Variable optical attenuator (VOA) 10 4.3 Optical fuse . 10 4.4 Optical power limiter 10 5 Re

20、quirements . 11 5.1 Classification . 11 5.1.1 General . 11 5.1.2 Type 11 5.1.3 Wavelength band . 12 5.1.4 Style 12 5.1.5 Variant. 13 5.1.6 Assessment level . 13 5.1.7 Normative reference extensions 13 5.2 Documentation 14 5.2.1 Symbols 14 5.2.2 Specification system 14 5.2.3 Drawings . 16 5.2.4 Tests

21、 and measurements . 16 5.2.5 Test data sheets 16 5.2.6 Instructions for use 17 5.3 Standardization system . 17 5.3.1 Interface standards 17 5.3.2 Performance standards 17 5.3.3 Reliability standards 18 5.3.4 Interlinking. 18 5.4 Design and construction 20 5.4.1 Materials . 20 5.4.2 Workmanship . 20

22、5.5 Quality 20 5.6 Performance 20 5.7 Identification and marking . 20 5.7.1 General . 20 5.7.2 Variant identification number . 20 5.7.3 Component marking. 20 5.7.4 Package marking . 21 5.8 Packaging . 21 5.9 Storage conditions. 21 5.10 Safety 21 60869-1 IEC:2012 3 Annex A (informative) Optical fuse

23、configuration and performance examples . 22 Annex B (informative) Optical fuse application notes 24 Annex C (informative) Optical power limiter configuration and performance examples 25 Annex D (informative) Optical power limiter application notes 28 Annex E (informative) Fixed optical attenuator ap

24、plication note . 30 Annex F (informative) Variable, manual or electrical optical attenuator application note . 31 Bibliography 33 Figure 1 Optical attenuator operation curve . 9 Figure 2 Optical fuse operation curve . 10 Figure 3 Optical power limiter operation curve . 11 Figure 4 Configuration A 12

25、 Figure 5 Configuration B 12 Figure 6 Configuration C 12 Figure 7 Standardization structure . 19 Figure A.1 Optical fuse, pigtail style . 22 Figure A.2 Optical fuse, plug style (LC plug) 22 Figure A.3 Response time curve of an optical fuse . 23 Figure A.4 Optical fuse, power threshold 30 dBm (1W), o

26、utput power drop at threshold 25 dB 23 Figure B.1 Optical fuse 24 Figure C.1 Optical power limiter, pigtail style . 25 Figure C.2 Optical power limiter, plug style (LC plug) . 25 Figure C.3 Optical power limiter Experimental 26 Figure C.4 Schematic optical power limiter response time 26 Figure C.5 S

27、chematic power definitions . 27 Figure C.6 Optical power limiter, input power definitions 27 Figure D.1 Optical power limiter and optical fuse, combined, operation curve 29 Figure E.1 Fixed optical attenuator 30 Figure F.1 The variable, manual or electrical, optical attenuator 32 Table 1 Three-level

28、 IEC specification structure 15 Table 2 Standards interlink matrix 19 4 60869-1 IEC:2012 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ FIBRE OPTIC INTERCONECTING DEVICES AND PASSIVE COMPONENTS FIBRE OPTIC PASSIVE POWER CONTROL DEVICES Part 1: Generic specification FOREWORD 1) The International Electro

29、technical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To

30、 this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC Natio

31、nal Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (IS

32、O) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation f

33、rom all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be

34、held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any

35、 divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to

36、 IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individua

37、l experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this

38、 IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this

39、 IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60869-1 has been prepared by subcommittee 86B: Fibre optic interconnecting devices and passive components, of IEC TC 86: Fibre optics. Thi

40、s fourth edition cancels and replaces the third edition, published in 1999, and constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: the terms and definitions were reconsidered; the requirement concerning the IEC Qu

41、ality Assessment System was reconsidered; the clause concerning quality assessment procedures was deleted. 60869-1 IEC:2012 5 The text of this standard is based on the following documents: FDIS Report on voting 86B/3505/FDIS 86B/3551/RVD Full information on the voting for the approval of this standa

42、rd can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all the parts in the IEC 60869 series, under the general title Fibre optic interconnecting devices and passive components Fibre optic p

43、assive power control devices, can be found on the IEC website. Future standards will carry the new general title as cited above. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“

44、in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. IMPORTANT The colour inside logo on the cover page of this publication indicates that it contains colours which are considered to be useful for th

45、e correct understanding of its contents. Users should therefore print this document using a colour printer. 6 60869-1 IEC:2012 FIBRE OPTIC INTERCONECTING DEVICES AND PASSIVE COMPONENTS FIBRE OPTIC PASSIVE POWER CONTROL DEVICES Part 1: Generic specification 1 Scope This part of IEC 60869 applies to f

46、ibre optic power control devices. These have all of the following general features: they are passive in that they contain no opto-electronic or other transducing elements; they have two ports for the transmission of optical power and control the transmitted power in a fixed or variable fashion; the

47、ports are unconnectorized optical fibre tails or optical fibre pigtails with connectors. This standard establishes generic requirements for the following passive optical devices: optical attenuator; optical fuse; optical power limiter. Test and measurement procedures for the above products are descr

48、ibed in IEC 61300-1, the IEC 61300-2 series and the 61300-3 series 1,2,3 1. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated re

49、ferences, the latest edition of the referenced document (including any amendments) applies. IEC 60027, Letter symbols to be used in electrical technology IEC 60050-731, International Electrotechnical Vocabulary Chapter 731: Optical fibre communication IEC 60617, Graphical symbols for diagrams. Available from IEC 60695-11-5, Fire hazard testing Part 11-