IEC 60749-38-2008 Semiconductor devices - Mechanical and climatic test methods - Part 38 Soft error test method for semiconductor devices with memory《半导体器件.机械和气候试验方法.第38部分 带存储器的半导体器件用软错误试验法》.pdf

《IEC 60749-38-2008 Semiconductor devices - Mechanical and climatic test methods - Part 38 Soft error test method for semiconductor devices with memory《半导体器件.机械和气候试验方法.第38部分 带存储器的半导体器件用软错误试验法》.pdf》由会员分享，可在线阅读，更多相关《IEC 60749-38-2008 Semiconductor devices - Mechanical and climatic test methods - Part 38 Soft error test method for semiconductor devices with memory《半导体器件.机械和气候试验方法.第38部分 带存储器的半导体器件用软错误试验法》.pdf（30页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 60749-38Edition 1.0 2008-02INTERNATIONAL STANDARD NORME INTERNATIONALESemiconductor devices Mechanical and climatic test methods Part 38: Soft error test method for semiconductor devices with memory Dispositifs semiconducteurs Mthodes dessais mcaniques et climatiques Partie 38: Mthode dessai de

2、s erreurs logicielles pour les dispositifs semiconducteurs avec mmoire IEC60749-38:2008 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2008 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any mea

3、ns, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,

4、 please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcan

5、ique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contac

6、tez le Comit national de la CEI de votre pays de rsidence. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes Internatio

7、nal Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IE

8、C publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date

9、 on all new IEC publications. Just Published details twice a month all new publications released. Available on-line and also by email. Electropedia: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in Engli

10、sh and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary online. Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Servi

11、ce Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des normes internationales pour tout ce qui a trait llectricit, llectronique et

12、aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue des publications de la CEI: www.iec.ch/searchpub/

13、cur_fut-f.htm Le Catalogue en-ligne de la CEI vous permet deffectuer des recherches en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Il donne aussi des informations sur les projets et les publications retires ou remplaces. Just Published CEI: www.iec.ch/online_news/justpub Re

14、stez inform sur les nouvelles publications de la CEI. Just Published dtaille deux fois par mois les nouvelles publications parues. Disponible en-ligne et aussi par email. Electropedia: www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient pl

15、us de 20 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International en ligne. Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commenta

16、ires sur cette publication ou si vous avez des questions, visitez le FAQ du Service clients ou contactez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC 60749-38Edition 1.0 2008-02INTERNATIONAL STANDARD NORME INTERNATIONALESemiconductor devices Mechanical and climatic test met

17、hods Part 38: Soft error test method for semiconductor devices with memory Dispositifs semiconducteurs Mthodes dessais mcaniques et climatiques Partie 38: Mthode dessai des erreurs logicielles pour les dispositifs semiconducteurs avec mmoire INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECT

18、ROTECHNIQUE INTERNATIONALE MICS 31.080.01 PRICE CODECODE PRIXISBN 2-8318-9615-0 2 60749-38 IEC:2008 CONTENTS FOREWORD.3 1 Scope.5 2 Terms and definitions .5 3 Test apparatus .7 3.1 Measurement equipment .7 3.2 Alpha radiation source.7 3.2.1 Background information.7 3.2.2 Preferred sources7 3.2.3 Var

19、iation in results.7 3.2.4 Effect of high radiation levels.7 3.2.5 Measurement accuracy8 3.3 Test sample 8 4 Procedure 8 4.1 Alpha radiation accelerated soft error test .8 4.1.1 Surface preparation .8 4.1.2 Power supply voltage 8 4.1.3 Ambient temperature .9 4.1.4 Core cycle time9 4.1.5 Data pattern

20、9 4.1.6 Distance between chip and radiation source 9 4.1.7 Number of measurement samples9 4.2 Real-time soft error test.9 4.2.1 General .9 4.2.2 Power supply voltage 9 4.2.3 Ambient temperature .9 4.2.4 Operating frequency 9 4.2.5 Data pattern 10 4.2.6 Test time .10 4.2.7 Number of test samples.10 4

21、.2.8 Environmental neutron testing .10 4.3 Neutron radiation accelerated soft error test10 5 Evaluation 10 5.1 Alpha radiation accelerated soft error test .10 5.2 Real-time soft error test.11 6 Summary12 Bibliography13 Figure 1 Effect of source-device spacing on normalized flux at device .8 Table 1

22、X for FIT calculation 11 60749-38 IEC:2008 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ SEMICONDUCTOR DEVICES MECHANICAL AND CLIMATIC TEST METHODS Part 38: Soft error test method for semiconductor devices with memory FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide org

23、anization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities

24、, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt

25、 with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined b

26、y agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3

27、) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they ar

28、e used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and t

29、he corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they ha

30、ve the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whats

31、oever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publica

32、tions is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Stand

33、ard IEC 60749-38 has been prepared by IEC technical committee 47: Semiconductor devices. The text of this standard is based on the following documents: FDIS Report on voting 47/1943/FDIS 47/1951/RVD Full information on the voting for the approval of this standard can be found in the report on voting

34、 indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. 4 60749-38 IEC:2008 A list of all the parts in the IEC 60749 series, under the general title Semiconductor devices Mechanical and climatic test methods, can be found on the IEC website

35、. The committee has decided that the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed; withdrawn; replace

36、d by a revised edition, or amended. 60749-38 IEC:2008 5 SEMICONDUCTOR DEVICES MECHANICAL AND CLIMATIC TEST METHODS Part 38: Soft error test method for semiconductor devices with memory 1 Scope This part of IEC 60749 establishes a procedure for measuring the soft error susceptibility of semiconductor

37、 devices with memory when subjected to energetic particles such as alpha radiation. Two tests are described; an accelerated test using an alpha radiation source and an (unaccelerated) real-time system test where any errors are generated under conditions of naturally occurring radiation which can be

38、alpha or other radiation such as neutron. To completely characterize the soft error capability of an integrated circuit with memory, the device must be tested for broad high energy spectrum and thermal neutrons using additional test methods. This test method may be applied to any type of integrated

39、circuit with memory device. 2 Terms and definitions For the purposes of this document, the following terms and definitions apply. 2.1 single-event upset SEU soft error caused by the transient signal induced by a single energetic-particle strike 2.2 soft error erroneous output signal from a latch or

40、memory cell that can be corrected by performing one or more normal functions of the device containing the latch or memory cell NOTE As commonly used, the term refers to an error caused by radiation or electromagnetic pulses and not to an error associated with a physical defect introduced during the

41、manufacturing process. 2.3 single-event hard error SHE irreversible change in operation resulting from a single radiation event and typically associated with permanent damage to one or more of the device elements (e.g. gate oxide rupture) 2.4 static soft error soft error that is not corrected by rep

42、eated reading but can be corrected by rewriting without the removal of power 2.5 transient soft error soft error that can be corrected by repeated reading without rewriting and without the removal of power 6 60749-38 IEC:2008 2.6 soft error, power cycle PCSE soft error that is not corrected by repea

43、ted reading or writing but can be corrected by the removal of power 2.7 single event functional interrupt SEFI soft error that causes the component to reset, lock-up, or otherwise malfunction in a detectable way, but does not require power cycling of the device (off and back on) to restore operabili

44、ty, unlike single-event latch-up (SEL), or result in permanent damage as in single-event burnout (SEB) 2.8 multiple bit upset MBU multiple-cell upset in which two or more error bits occur in the same word 2.9 single event latch up SEL abnormal high-current state in a device caused by the passage of

45、a single energetic particle through sensitive regions of the device structure and resulting in the loss of device functionality NOTE 1 SEL may cause permanent damage to the device. If the device is not permanently damaged, power cycling of the device (off and back on) is necessary to restore normal

46、operation. NOTE 2 An example of SEL in a CMOS device is when the passage of a single particle induces the creation of parasitic bipolar (p-n-p-n) shorting of power to ground. 2.10 flux (of particle radiation) time rate of flow of particles emitted from or incident on a surface, divided by the area o

47、f that surface NOTE The flux is usually expressed in particles per square centimeter second (N/cm2s) or particles per square centimeter hour (N/cm2h). 2.11 alpha source activity number of alpha particle decays in the alpha source per unit time NOTE The preferred SI unit is the Becquerel (Bq); to con

48、vert from the Curie, multiply by 3,7 1010(exactly). 2.12 soft error rate SER rate at which soft errors occur 2.13 failures in time FIT the number of failures in 109device-hours 2.14 multiple-cell upset MCU single event that induces several bits in an IC to have a soft error at one time 60749-38 IEC:

49、2008 7 NOTE The bits are usually, but not always, adjacent. 3 Test apparatus 3.1 Measurement equipment The equipment shall be capable of measuring the functions of the integrated circuit devices, and capable of measuring the time taken for the change of stored data by the exposure to energetic particles, such as alpha radiation to take place (i.e. the generation of a soft error). Alternatively, the