IEC 60749-37-2008 Semiconductor devices - Mechanical and climatic test methods - Part 37 Board level drop test method using an accelerometer《半导体装置.机械和气候试验方法.第37部分 用加速计的电路板级落锤试验方法》.pdf

《IEC 60749-37-2008 Semiconductor devices - Mechanical and climatic test methods - Part 37 Board level drop test method using an accelerometer《半导体装置.机械和气候试验方法.第37部分 用加速计的电路板级落锤试验方法》.pdf》由会员分享，可在线阅读，更多相关《IEC 60749-37-2008 Semiconductor devices - Mechanical and climatic test methods - Part 37 Board level drop test method using an accelerometer《半导体装置.机械和气候试验方法.第37部分 用加速计的电路板级落锤试验方法》.pdf（44页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 60749-37Edition 1.0 2008-01INTERNATIONAL STANDARD NORME INTERNATIONALESemiconductor devices Mechanical and climatic test methods Part 37: Board level drop test method using an accelerometer Dispositifs semiconducteurs Mthodes dessais mcaniques et climatiques Partie 37: Mthode dessai de chute au

2、 niveau de la carte avec utilisation dun acclromtre IEC60749-37:2008 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2008 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or m

3、echanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the

4、 address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la

5、photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit nation

6、al de la CEI de votre pays de rsidence. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for a

7、ll electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www

8、.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC pub

9、lications. Just Published details twice a month all new publications released. Available on-line and also by email. Electropedia: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with

10、 equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary online. Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or co

11、ntact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies ap

12、parentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Ca

13、talogue en-ligne de la CEI vous permet deffectuer des recherches en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Il donne aussi des informations sur les projets et les publications retires ou remplaces. Just Published CEI: www.iec.ch/online_news/justpub Restez inform sur les

14、 nouvelles publications de la CEI. Just Published dtaille deux fois par mois les nouvelles publications parues. Disponible en-ligne et aussi par email. Electropedia: www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 20 000 termes

15、 et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International en ligne. Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette publ

16、ication ou si vous avez des questions, visitez le FAQ du Service clients ou contactez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC 60749-37Edition 1.0 2008-01INTERNATIONAL STANDARD NORME INTERNATIONALESemiconductor devices Mechanical and climatic test methods Part 37: Board

17、 level drop test method using an accelerometer Dispositifs semiconducteurs Mthodes dessais mcaniques et climatiques Partie 37: Mthode dessai de chute au niveau de la carte avec utilisation dun acclromtre INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE RICS 31.080

18、.01 PRICE CODECODE PRIXISBN 2-8318-9569-3 2 60749-37 IEC:2008 CONTENTS FOREWORD.3 INTRODUCTION.5 1 Scope and object6 2 Normative references .6 3 Terms and definitions .6 4 Test apparatus and components.7 4.1 Test apparatus 7 4.2 Test components.8 4.3 Test board.8 4.4 Test board assembly .8 4.5 Numbe

19、r of components and sample size .9 5 Test procedure .9 5.1 Test equipment and parameters 9 5.2 Pre-test characterization .10 5.3 Drop testing.12 6 Failure criteria and failure analysis .12 7 Summary14 Annex A (informative) Preferred board construction, material, design and layout .15 Bibliography19

20、Figure 1 Typical drop test apparatus and mounting scheme for PCB assembly 10 Figure 2 Typical shock test half-sine pulse graphic and formulae .11 Figure 3 Fundamental mode of vibration of PCB supported with four screws14 Figure A.1 Recommended test board size and layout.18 Table 1 Quantity of test b

21、oards and components required for testing .9 Table 2 Component locations for test boards .13 Table A.1 Test board stack-up and material .15 Table A.2 Mechanical property requirements for dielectric materials 16 Table A.3 Recommended test board pad sizes and solder mask openings .17 Table A.4 X, Y lo

22、cations for components centre 18 60749-37 IEC:2008 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ SEMICONDUCTOR DEVICES MECHANICAL AND CLIMATIC TEST METHODS Part 37: Board level drop test method using an accelerometer FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide orga

23、nization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities,

24、 IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt

25、with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by

26、 agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3)

27、 IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are

28、 used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and th

29、e corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they hav

30、e the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatso

31、ever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publicat

32、ions is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standa

33、rd IEC 60749-37 has been prepared by IEC technical committee 47: Semiconductor devices. This standard cancels and replaces IEC/PAS 62050 published in 2004. This first edition constitutes a technical revision. The text of this standard is based on the following documents: FDIS Report on voting 47/193

34、7/FDIS 47/1948/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. 4 60749-37 IEC:2008 This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts of the IEC 60749 series,

35、 under the general title Semiconductor devices Mechanical and climatic test methods, can be found in the IEC website. The committee has decided that the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC web site under “http:/webstore.iec.ch“ in

36、 the data related to the specific publication. At this date, the publication will be reconfirmed; withdrawn; replaced by a revised edition, or amended. 60749-37 IEC:2008 5 INTRODUCTION Handheld electronic products fit into the consumer and portable market segments. Included in handheld electronic pr

37、oducts are cameras, calculators, cell phones, cordless phones, pagers, palm size PCs, personal computer memory card international association (PCMCIA) cards, smart cards, personal digital assistants (PDAs) and other electronic products that can be conveniently stored in a pocket and used while held

38、in users hand. These handheld electronic products are more prone to being dropped during their useful service life because of their size and weight. This dropping event can not only cause mechanical failures in the housing of the device but also create electrical failures in the printed circuit boar

39、d (PCB) assemblies mounted inside the housing due to transfer of energy through PCB supports. The electrical failures may result from various failure modes such as cracking of the circuit board, track cracking on the board, cracking of solder interconnections between the components and the board, an

40、d component cracks. The primary driver of these failures is excessive flexing of the circuit board due to input acceleration to the board created from dropping the handheld electronic product. This flexing of the board causes relative motion between the board and the components mounted on it, result

41、ing in component, interconnect or board failures. The failure is a function of the combination of the board design, construction, material, thickness and surface finish; interconnect material and standoff height and component size. Correlation between test and field conditions is not yet fully estab

42、lished. Consequently, the test procedure is presently more appropriate for relative component performance than for use as a pass/fail criterion. Rather, results should be used to augment existing data or establish a baseline for potential investigative efforts in package/board technologies. The comp

43、arability between different test sites, data acquisition methods, and board manufacturers has not been fully demonstrated by existing data. As a result, if the data are to be used for direct comparison of component performance, matching studies must first be performed to prove that the data are in f

44、act comparable across different test sites and test conditions. This method is not intended to substitute for full characterization testing, which might incorporate substantially larger sample sizes and increased number of drops. Due to limited sample size and number of drops specified here, it is p

45、ossible that enough failure data may not be generated in every case to perform full statistical analysis. 6 60749-37 IEC:2008 SEMICONDUCTOR DEVICES MECHANICAL AND CLIMATIC TEST METHODS Part 37: Board level drop test method using an accelerometer 1 Scope and object This part of IEC 60749 provides a t

46、est method that is intended to evaluate and compare drop performance of surface mount electronic components for handheld electronic product applications in an accelerated test environment, where excessive flexure of a circuit board causes product failure. The purpose is to standardize the test board

47、 and test methodology to provide a reproducible assessment of the drop test performance of surface-mounted components while producing the same failure modes normally observed during product level test. The purpose of this standard is to prescribe a standardized test method and reporting procedure. T

48、his is not a component qualification test and is not meant to replace any system level drop test that may be needed to qualify a specific handheld electronic product. The standard is not meant to cover the drop test required to simulate shipping and handling-related shock of electronic components or

49、 PCB assemblies. These requirements are already addressed in test methods such as IEC 60749-10. The method is applicable to both area array and perimeter-leaded surface mounted packages. This test method uses an accelerometer to measure the mechanical shock duration and magnitude applied which is proportional to the stress on a given component mounted on a standard board. The test method