IEC 60695-4-2012 Fire hazard testing - Part 4 Terminology concerning fire tests for electrotechnical products《着火危险试验.第4部分 电工产品着火试验术语》.pdf

《IEC 60695-4-2012 Fire hazard testing - Part 4 Terminology concerning fire tests for electrotechnical products《着火危险试验.第4部分 电工产品着火试验术语》.pdf》由会员分享，可在线阅读，更多相关《IEC 60695-4-2012 Fire hazard testing - Part 4 Terminology concerning fire tests for electrotechnical products《着火危险试验.第4部分 电工产品着火试验术语》.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 60695-4 Edition 4.0 2012-05 INTERNATIONAL STANDARD NORME INTERNATIONALE Fire hazard testing Part 4: Terminology concerning fire tests for electrotechnical products Essais relatifs aux risques du feu Partie 4: Terminologie relative aux essais au feu pour les produits lectrotechniques IEC 60695-4

2、:2012 BASIC SAFETY PUBLICATION PUBLICATION FONDAMENTALE DE SCURIT THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2012 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mech

3、anical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the ad

4、dress below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la pho

5、tocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national

6、de la CEI de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes I

7、nternational Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Useful

8、 links: IEC publications search - www.iec.ch/searchpub The advanced search enables you to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/ju

9、stpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 ter

10、ms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, pleas

11、e contact the Customer Service Centre: csciec.ch. A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des

12、 publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub La recherche avance vous permet d

13、e trouver des publications CEI en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications de la CE

14、I. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en

15、franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: c

16、sciec.ch. IEC 60695-4 Edition 4.0 2012-05 INTERNATIONAL STANDARD NORME INTERNATIONALE Fire hazard testing Part 4: Terminology concerning fire tests for electrotechnical products Essais relatifs aux risques du feu Partie 4: Terminologie relative aux essais au feu pour les produits lectrotechniques IN

17、TERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE J ICS 01.040.13; 29.020 PRICE CODE CODE PRIX ISBN 978-2-88912-047-5 BASIC SAFETY PUBLICATION PUBLICATION FONDAMENTALE DE SCURIT Registered trademark of the International Electrotechnical Commission Marque dpose de la

18、Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. 2 60695-4 IEC:2012 CONTENTS FOREWORD . 3 1 Scope . 5 2 Normative reference

19、s . 5 3 Terms and definitions . 5 3.1 Use of the term “item” 5 3.2 Other terms and definitions . 5 60695-4 IEC:2012 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ FIRE HAZARD TESTING Part 4: Terminology concerning fire tests for electrotechnical products FOREWORD 1) The International Electrotechnical

20、 Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end

21、 and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Commi

22、ttee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in ac

23、cordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all

24、interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held res

25、ponsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any diverge

26、nce between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC mar

27、ks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual expert

28、s and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Pub

29、lication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Pub

30、lication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60695-4 has been prepared by IEC technical committee 89: Fire hazard testing. The text of this standard is based on the following documents: FDIS

31、Report on voting 89/1098/FDIS 89/1112/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. This fourth edition of IEC 60695-4 cancel

32、s and replaces the third edition issued in 2005. It constitutes a technical revision. 4 60695-4 IEC:2012 This standard has the status of a basic safety publication in accordance with IEC Guide 104 and ISO/IEC Guide 51. The main changes with respect to the previous edition are listed below: The terms

33、 and definitions that are not specifically electrotechnical and that are either identical or equivalent to those in ISO 13943:2008 have been deleted. The terms and definitions that are specifically electrotechnical and that are in ISO 13943:2008 have been included for the convenience of the user. So

34、me new terms have been included. A list of all the parts in the IEC 60695 series, under the general title Fire hazard testing, can be found on the IEC website. The following introductory elements represent a series of publications: Part 1: Guidance for assessing the fire hazard of electrotechnical p

35、roducts Part 2: Glowing/hot-wire based test methods Part 4: Terminology concerning fire tests for electrotechnical products Part 5: Corrosion damage effects of fire effluent Part 6: Smoke obscuration Part 7: Toxicity of fire effluent Part 8: Heat release Part 9: Surface spread of flame Part 10: Abno

36、rmal heat Part 11: Test flames The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed

37、, withdrawn, replaced by a revised edition, or amended. 60695-4 IEC:2012 5 FIRE HAZARD TESTING Part 4: Terminology concerning fire tests for electrotechnical products 1 Scope The terms and definitions in this standard are applicable to fire tests for electrotechnical products. This basic safety publ

38、ication is intended for use by technical committees in the preparation of standards in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the prepara

39、tion of its publications. The requirements, test methods or test conditions of this basic safety publication will not apply unless specifically referred to or included in the relevant publications. 2 Normative references The following documents, in whole or in part, are normatively referenced in thi

40、s document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC Guide 104:2010, The preparation of safety publications and the use of basic safety

41、 publications and group safety publications IEC 60050, International Electrotechnical vocabulary ISO 13943:2008, Fire safety Vocabulary ISO/IEC Guide 51:1999, Safety aspects Guidelines for their inclusion in standards 3 Terms and definitions 3.1 Use of the term “item” For the purposes of this docume

42、nt, the English term “item” is used in a general meaning to represent any single object or assembly of objects, and may cover, for example, material, product, assembly, structure or building, as required in the context of any individual definition. If the “item” under consideration is a test specime

43、n then the term “test specimen” is used. 3.2 Other terms and definitions For the purposes of this document, the following terms and definitions apply. NOTE Terms and definitions that are specifically electrotechnical and that are in ISO 13943:2008 have been included below for the convenience of the

44、user. 6 60695-4 IEC:2012 3.2.1 abnormal heat electrotechnical heat that is additional to that resulting from use under normal conditions, up to and including that which causes a fire SOURCE: ISO 13943:2008, definition 4.1 3.2.2 arc resistance electrotechnical ability of an electrically insulating ma

45、terial to resist the influence of an electric arc, under specified conditions Note 1 to entry: The arc resistance is identified by the length of the arc, the absence or presence of a conducting path and the burning or damage of the test specimen. SOURCE: ISO 13943:2008, definition 4.13 3.2.3 arc tra

46、cking tracking electrotechnical progressive formation of conducting paths that are produced on the surface and/or within a solid insulating material, due to the combined effects of electric stress and electrolytic contamination SEE: tracking resistance (3.2.27) SOURCE: ISO 13943:2008, definition 4.3

47、42 3.2.4 confirmatory test procedure intended as a diagnostic indicator to reveal anomalous behaviour or conditions in a test flame, burner or associated hardware 3.2.5 enclosure housing affording the type and degree of protection suitable for the intended application SOURCE: IEC 60050-195:1998, 195

48、-02-35 3.2.6 enclosure electrotechnical external casing protecting the electrical and mechanical parts of apparatus Note 1 to entry: The term excludes cables. SOURCE: ISO 13943:2008, definition 4.78 3.2.7 end product product that is ready for use without modification NOTE 1 to entry: An end product

49、can be a component of another end product. 3.2.8 end product fire test fire test that is carried out on an end product and is described in a relevant specification. Note 1 to entry: End product fire tests may be small-scale, intermediate-scale, large-scale or real-scale. 60695-4 IEC:2012 7 3.2.9 extent of combustion electrotechnical maximum length of a test specimen that has been destroyed by combustion or pyrol