IEC 60670-24-2011 Boxes and enclosures for electrical accessories for household and similar fixed electrical installations - Part 24 Particular requirements for enclosures for hous.pdf

《IEC 60670-24-2011 Boxes and enclosures for electrical accessories for household and similar fixed electrical installations - Part 24 Particular requirements for enclosures for hous.pdf》由会员分享，可在线阅读，更多相关《IEC 60670-24-2011 Boxes and enclosures for electrical accessories for household and similar fixed electrical installations - Part 24 Particular requirements for enclosures for hous.pdf（70页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 60670-24 Edition 2.0 2011-03 INTERNATIONAL STANDARD NORME INTERNATIONALE Boxes and enclosures for electrical accessories for household and similar fixed electrical installations Part 24: Particular requirements for enclosures for housing protective devices and other power dissipating electrical

2、 equipment Botes et enveloppes pour appareillage lectrique pour installations lectriques fixes pour usages domestiques et analogues Partie 24: Exigences particulires pour enveloppes pour appareillages de protection et autres appareillages lectriques ayant une puissance dissipe IEC 60670-24:2011 THIS

3、 PUBLICATION IS COPYRIGHT PROTECTED Copyright 2011 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in wr

4、iting from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further in

5、formation. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit nat

6、ional de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office 3, rue de Vare

7、mb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publication

8、s The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a va

9、riety of criteria (reference number, text, technical committee,). It also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month all new publications rele

10、ased. Available on-line and also by email. Electropedia: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the Internationa

11、l Electrotechnical Vocabulary online. Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 A

12、 propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publicat

13、ions de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue en-ligne de la CEI vous permet deffectuer des recherches en utili

14、sant diffrents critres (numro de rfrence, texte, comit dtudes,). Il donne aussi des informations sur les projets et les publications retires ou remplaces. Just Published CEI: www.iec.ch/online_news/justpub Restez inform sur les nouvelles publications de la CEI. Just Published dtaille deux fois par m

15、ois les nouvelles publications parues. Disponible en-ligne et aussi par email. Electropedia: www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 20 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents

16、dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International en ligne. Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du Service clients

17、ou contactez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC 60670-24 Edition 2.0 2011-03 INTERNATIONAL STANDARD NORME INTERNATIONALE Boxes and enclosures for electrical accessories for household and similar fixed electrical installations Part 24: Particular requirements for e

18、nclosures for housing protective devices and other power dissipating electrical equipment Botes et enveloppes pour appareillage lectrique pour installations lectriques fixes pour usages domestiques et analogues Partie 24: Exigences particulires pour enveloppes pour appareillages de protection et aut

19、res appareillages lectriques ayant une puissance dissipe INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE V ICS 29.120.10 PRICE CODE CODE PRIX ISBN 978-2-88912-391-9 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commissio

20、n Electrotechnique Internationale 2 60670-24 IEC:2011 CONTENTS FOREWORD . 4 1 Scope 6 2 Normative references. 6 3 Definitions . 7 4 General requirements 8 5 General notes on tests . 8 6 Ratings 8 7 Classification . 8 8 Marking . 8 9 Dimensions 10 10 Protection against electric shock 10 11 Provisions

21、 for earthing . 11 12 Construction 11 13 Resistance to ageing, protection against ingress of solid foreign objects and against harmful ingress of water 12 14 Insulation resistance and electric strength . 12 15 Mechanical strength . 12 16 Resistance to heat . 12 17 Creepage distances, clearances and

22、distances through sealing compound 12 18 Resistance of insulating material to abnormal heat and to fire 13 19 Resistance to tracking . 13 20 Resistance to corrosion . 14 21 Electromagnetic compatibility 14 101 Verification of the maximum capability to dissipate power (P de ) . 14 102 Verification of

23、 temperature rise 15 Annex AA (normative) Instructions to be given by the manufacturer of the GP enclosure to the installer how to integrate accessories, and example of calculation 22 Annex BB (normative) Instructions to be given by the manufacturer of the PD enclosure to the installer how to integr

24、ate accessories . 30 Bibliography 32 Figure 101 Arrangement for the verification of the maximum capability to dissipate power (P de ) and for verification of temperature rise of surface type enclosures . 17 Figure 102 Heating resistor for the verification of the maximum capability to dissipate power

25、 (P de ) . 18 Figure 103 Position of the resistor for enclosures designed or intended to be fitted with rail mounting modular accessories and electrical equipment 19 Figure 104 Position of the resistor(s) for enclosures other than those designed or intended to be fitted with rail mounting accessorie

26、s and electrical equipment . 20 Figure 105 Position of the resistor(s) for enclosures other than those designed or intended to be fitted with rail mounting accessories and electrical equipment and allowing the mounting of several accessories and electrical equipment in different positions . 21 60670

27、-24 IEC:2011 3 Table 1 Classification of boxes and enclosures 8 Table 101 Creepage distances, clearances and distances through sealing compound . 13 Table 102 Diversity factor 16 Table 103 Temperatures of accessible surfaces . 17 Table AA.1 Diversity factor 24 Table AA.2 Tests and verifications . 25

28、 Table AA.3 Calculation of P dp28 Table AA.4 Calculation of P au29 4 60670-24 IEC:2011 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ BOXES AND ENCLOSURES FOR ELECTRICAL ACCESSORIES FOR HOUSEHOLD AND SIMILAR FIXED ELECTRICAL INSTALLATIONS Part 24: Particular requirements for enclosures for housing prot

29、ective devices and other power dissipating electrical equipment FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international

30、 co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referr

31、ed to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in

32、this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an internati

33、onal consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable

34、 efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publ

35、ications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity.

36、 Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7

37、) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for co

38、sts (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct appli

39、cation of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60670-24 has been prepared by subcom

40、mittee 23B: Plugs, socket- outlets and switches, of IEC technical committee 23: Electrical accessories. This second edition cancels and replaces the first edition published in 2005 and constitutes a technical revision. The following major changes from the first edition are introduced: new definition

41、 for basic, general purpose enclosures (GP enclosure) and enclosures for pre-determined equipment (PD enclosure); new classification and marking for general purpose enclosure (GP enclosure) and enclosure for pre-determined equipment (PD enclosure); required data for instruction sheet and/or document

42、ation according to the type of enclosure; 60670-24 IEC:2011 5 adequate space to allow mounting and connection of the accessories (fully equipped) as declared by the manufacturer; requirements for general purpose enclosure (GP enclosure) as in Clause 101; requirements for enclosure for pre-determined

43、 equipment (PD enclosure) as in Clause 102; instructions to be given by the manufacturer of the GP enclosure to the installer how to integrate accessories and example of calculation given in Annex AA; instructions to be given by the manufacturer of the PD enclosure to the installer how to integrate

44、accessories given in Annex BB. The text of this standard is based on the following documents: FDIS Report on voting 23B/982/FDIS 23B/992/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been d

45、rafted in accordance with the ISO/IEC Directives, Part 2. This standard shall be used in conjunction with IEC 60670-1. It lists the changes necessary to convert that standard into a specific standard for housing protective devices and other power dissipating electrical equipment. Where this Part 24

46、states “addition“, “modification“ or “replacement“, the relevant requirement, test specifications or explanatory matter in Part 1 shall be adapted accordingly. Clauses and subclauses, notes, figures or tables which are additional to those in Part 1 are numbered starting from 101. Additional annexes

47、to Part 1 are numbered AA, BB, etc. In this publication the following print types are used: requirements proper: in roman type. test specifications: in italic type. notes: in smaller roman type. A list of all the parts in the IEC 60670 series, under the general title Boxes and enclosures for electri

48、cal accessories for household and similar fixed electrical installations, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to

49、 the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. 6 60670-24 IEC:2011 BOXES AND ENCLOSURES FOR ELECTRICAL ACCESSORIES FOR HOUSEHOLD AND SIMILAR FIXED ELECTRICAL INSTALLATIONS Part 24: Particular requirements for enclosures for housing protective devices and other power dissipating electrical equipment 1