IEC 60243-2-2013 Electric strength of insulating materials - Test methods - Part 2 Additional requirements for tests using direct voltage《绝缘材料的耐电强度 试验方法 第2部分 采用直流电压进行试验的补充要求》.pdf

《IEC 60243-2-2013 Electric strength of insulating materials - Test methods - Part 2 Additional requirements for tests using direct voltage《绝缘材料的耐电强度 试验方法 第2部分 采用直流电压进行试验的补充要求》.pdf》由会员分享，可在线阅读，更多相关《IEC 60243-2-2013 Electric strength of insulating materials - Test methods - Part 2 Additional requirements for tests using direct voltage《绝缘材料的耐电强度 试验方法 第2部分 采用直流电压进行试验的补充要求》.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 60243-2 Edition 3.0 2013-11 INTERNATIONAL STANDARD NORME INTERNATIONALE Electric strength of insulating materials Test methods Part 2: Additional requirements for tests using direct voltage Rigidit dilectrique des matriaux isolants Mthodes dessai Partie 2: Exigences complmentaires pour les essa

2、is tension continue IEC60243-2:2013 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2013 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying

3、 and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC

4、member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, san

5、s laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsi

6、dence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all

7、 electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Useful links: IEC publications searc

8、h - www.iec.ch/searchpub The advanced search enables you to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on

9、 all new IEC publications. Just Published details all new publications released. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English

10、and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service

11、 Centre: csciec.ch. A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu t

12、echnique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub La recherche avance vous permet de trouver des publications CEI

13、 en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications de la CEI. Just Published dtaille les

14、nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en franais, ainsi que les termes

15、quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 60243-2 Edition

16、3.0 2013-11 INTERNATIONAL STANDARD NORME INTERNATIONALE Electric strength of insulating materials Test methods Part 2: Additional requirements for tests using direct voltage Rigidit dilectrique des matriaux isolants Mthodes dessai Partie 2: Exigences complmentaires pour les essais tension continue I

17、NTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE J ICS 17.220.99; 29.035.01 PRICE CODE CODE PRIX ISBN 978-2-8322-1200-4 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make

18、 sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. 2 60243-2 IEC:2013 CONTENTS FOREWORD . 3 1 Scope 5 2 Normative references 5 3 Terms and definitions 5 4 Significance of the test 5

19、 5 Electrodes and test specimens 6 6 Conditioning before tests . 6 7 Surrounding medium . 6 8 Electrical apparatus . 6 8.1 Voltage source . 6 8.2 Voltage measurement 7 9 Procedure 7 10 Mode of increase of voltage . 7 11 Criterion of breakdown 7 12 Number of tests . 7 13 Report . 7 Bibliography 8 602

20、43-2 IEC:2013 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ ELECTRIC STRENGTH OF INSULATING MATERIALS TEST METHODS Part 2: Additional requirements for tests using direct voltage FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising

21、 all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards,

22、 Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparator

23、y work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organization

24、s. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of reco

25、mmendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by a

26、ny end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional pu

27、blication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by inde

28、pendent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any

29、 personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normativ

30、e references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsib

31、le for identifying any or all such patent rights. International Standard IEC 60243-2 has been prepared by technical committee 112: Evaluation and qualification of electrical insulation materials and systems This third edition cancels and replaces the second edition published in 2001, and constitutes

32、 an editorial revision. This standard shall be read in conjunction with IEC 60243-1. The text of this standard is based on the following documents: CDV Report on voting 112/245/CDV 112/266A/RVC 4 60243-2 IEC:2013 Full information on the voting for the approval of this standard can be found in the re

33、port on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts in the IEC 60243 series, published under the general title Electric strength of insulating materials Test methods, can be found on the IEC website. Th

34、e committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revise

35、d edition, or amended. 60243-2 IEC:2013 5 ELECTRIC STRENGTH OF INSULATING MATERIALS TEST METHODS Part 2: Additional requirements for tests using direct voltage 1 Scope This part of IEC 60243 gives requirements additional to those in IEC 60243-1 for the determination of the electric strength of solid

36、 insulating materials under direct voltage stress. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edit

37、ion of the referenced document (including any amendments) applies. IEC 60243-1:2013, Electric strength of insulating materials Test methods Part 1: Tests at power frequencies 3 Terms and definitions For the purposes of this document, the terms and definitions in IEC 60243-1:2013 apply. 4 Significanc

38、e of the test In addition to the requirements of Clause 4 of IEC 60243-1:2013, the following points shall be considered when using direct-voltage tests. For a non-homogeneous test specimen, with alternating voltage, the distribution of voltage stress within the test specimen is determined by impedan

39、ce (largely capacitive). With an increasing direct voltage, the voltage distribution may still be largely capacitive but depends partly on the rate of voltage increase. The resistive voltage distribution, after constant voltage application, represents the steady-state condition. The choice between d

40、irect or alternating voltage depends upon the purpose for which the breakdown test is to be used and, to some extent, on the intended application of the material. Upon direct voltage application, the following currents result: the capacitive current, the electric absorption current, the leakage curr

41、ent and, in some cases, partial discharge currents. In addition, for materials with dissimilar layers or discontinuities, the voltage distribution across the test specimen is also influenced, as a result of interfacial polarization, by charges of opposite polarity, which may accumulate on the two si

42、des of the interface and create local fields sufficiently strong to produce partial discharges and/or breakdown of the test specimens. For most materials, the d.c. breakdown voltage is higher than the peak value of the power-frequency breakdown voltage; for many materials, particularly those which a

43、re non-homogeneous, the d.c. breakdown voltage will be three times higher than the a.c. breakdown voltage or even more. 6 60243-2 IEC:2013 5 Electrodes and test specimens For the purposes of this standard, the electrode configurations and shape of test specimen of Clause 5 of IEC 60243-1:2013 are ap

44、plicable. 6 Conditioning before tests Clause 6 of IEC 60243-1:2013 is applicable. 7 Surrounding medium Clause 7 of IEC 60243-1:2013 is applicable. 8 Electrical apparatus 8.1 Voltage source The test voltage applied to the electrodes shall be provided by a power supply having the following characteris

45、tics and components. A choice of voltage of either positive or negative polarity shall be provided, one of the connections to the electrodes being earthed. The voltage ripple on the test voltage shall not exceed 2 % of the voltage at all values greater than 50 % of the breakdown voltage. The test vo

46、ltage shall also be free from transients or other fluctuations exceeding 1 % of the applied voltage. When testing test specimens of low capacitance, it may be necessary to add a suitable capacitor (for example, 1 000 pF) in parallel with the electrodes in order to reduce the influence of transients

47、in initiating premature breakdowns. The controls on voltage shall be capable of varying the test voltage smoothly and uniformly between zero and the maximum test voltage and with the requested rate of voltage rise. The rate of voltage rise shall be controllable within 20 % of the specified rate. Ste

48、ps in voltage rise shall not exceed 2 % of the expected breakdown voltage value. Controls which automatically increase the voltage at a selectable rate are preferable. A current-sensitive interrupting device shall be used for switching off the direct voltage source. For many materials, a dangerous v

49、oltage may persist across the test specimen for a considerable time after the d.c. test voltage is removed. Disconnection of the power supply to the direct voltage source does not necessarily result in the output voltage or the voltage at the electrodes being reduced to zero. For this reason, it is essential that the electrodes be short-circuited and connected to earth for a period equal to minimum twice the total charging t