IEC 60127-6-2014 Miniature fuses - Part 6 Fuse-holders for miniature fuse-links《小型熔断器 第6部分 小型管状熔断体的熔断器座》.pdf

《IEC 60127-6-2014 Miniature fuses - Part 6 Fuse-holders for miniature fuse-links《小型熔断器 第6部分 小型管状熔断体的熔断器座》.pdf》由会员分享，可在线阅读，更多相关《IEC 60127-6-2014 Miniature fuses - Part 6 Fuse-holders for miniature fuse-links《小型熔断器 第6部分 小型管状熔断体的熔断器座》.pdf（114页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 60127-6 Edition 2.0 2014-09 INTERNATIONAL STANDARD NORME INTERNATIONALE Miniature fuses Part 6: Fuse-holders for miniature fuse-links Coupe-circuits miniatures Partie 6: Ensembles-porteurs pour cartouches de coupe-circuits miniatures IEC 60127-6:2014-09(en-fr) THIS PUBLICATION IS COPYRIGHT PROT

2、ECTED Copyright 2014 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs

3、member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduct

4、ion rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de lIEC ou du Comit national de lIEC du pays du demande

5、ur. Si vous avez des questions sur le copyright de lIEC ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de lIEC de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22

6、919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The t

7、echnical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. IEC Catalogue - webstore.iec.ch/catalogue The stand-alone application for consulting the entire bibliographical in

8、formation on IEC International Standards, Technical Specifications, Technical Reports and other documents. Available for PC, Mac OS, Android Tablets and iPad. IEC publications search - www.iec.ch/searchpub The advanced search enables to find IEC publications by a variety of criteria (reference numbe

9、r, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available online and also once a month by

10、email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms in 14 additional languages. Also known as the International Electrotechnical Vocabulary (I

11、EV) online. IEC Glossary - std.iec.ch/glossary More than 55 000 electrotechnical terminology entries in English and French extracted from the Terms and Definitions clause of IEC publications issued since 2002. Some entries have been collected from earlier publications of IEC TC 37, 77, 86 and CISPR.

12、 IEC Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. A propos de lIEC La Commission Electrotechnique Internationale (IEC) est la premire organisation mondiale qui

13、 labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications IEC Le contenu technique des publications IEC est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum o

14、u amendement peut avoir t publi. Catalogue IEC - webstore.iec.ch/catalogue Application autonome pour consulter tous les renseignements bibliographiques sur les Normes internationales, Spcifications techniques, Rapports techniques et autres documents de lIEC. Disponible pour PC, Mac OS, tablettes And

15、roid et iPad. Recherche de publications IEC - www.iec.ch/searchpub La recherche avance permet de trouver des publications IEC en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. IEC Just

16、Published - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications IEC. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne de termes lectroniques

17、et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans 14 langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (IEV) en ligne. Glossaire IEC - std.iec.ch/glossary Plus de 55 000 entres terminologique

18、s lectrotechniques, en anglais et en franais, extraites des articles Termes et Dfinitions des publications IEC parues depuis 2002. Plus certaines entres antrieures extraites des publications des CE 37, 77, 86 et CISPR de lIEC. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des comm

19、entaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 60127-6 Edition 2.0 2014-09 INTERNATIONAL STANDARD NORME INTERNATIONALE Miniature fuses Part 6: Fuse-holders for miniature fuse-links Coupe-circuits miniatures Partie 6: Ensembles-porteurs pour cartouches de

20、coupe-circuits miniatures INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE XA ICS 29.120.50 PRICE CODE CODE PRIX ISBN 978-2-8322-1830-3 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internation

21、ale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. 2 IEC 60127-6:2014 IEC 2014 CONTENTS FOREWORD . 6 INTRODUCTION . 8 1 Scope 9 2 Normative references 10 3 Terms an

22、d definitions 11 3.1 Fuse-holders . 12 4 General requirements 15 5 Preferred standard ratings and classifications for fuse-holders 15 6 Marking . 16 7 Clause deleted 16 8 General notes on tests 16 8.1 Nature of tests 16 8.2 Standard atmospheric conditions for measurement and tests 17 8.3 Preconditio

23、ning of test samples 17 8.4 Nature of supply . 17 8.5 Gauges and dummy fuse-links for tests . 17 8.5.1 Gauges and dummy fuse-links according to IEC 60127-2 17 8.5.2 Gauges and dummy fuse-links according to IEC 60127-3 18 8.6 Type tests . 20 9 Protection against electric shock . 20 9.1 Category PC1:

24、Fuse-holders without integral protection against electric shock 20 9.2 Category PC2: Fuse-holders with integral protection against electric shock 21 9.3 Category PC3: Fuse-holders with enhanced integral protection against electric shock 21 10 Clearances and creepage distances 21 10.1 General . 21 10

25、.2 Minimum requirements for fuse-holders in respect to the grade of insulation . 21 10.3 Clearances . 22 10.4 Creepage distances 23 11 Electrical requirements 24 11.1 Insulation resistance, dielectric strength and impulse withstand voltage 24 11.1.1 Mounting . 24 11.1.2 Humidity preconditioning . 25

26、 11.1.3 Measurement of insulation resistance 25 11.1.4 Dielectric strength test . 26 11.1.5 Impulse withstand voltage test . 26 11.2 Contact resistance 26 11.2.1 General measuring requirements . 26 11.2.2 Measuring cycle. 27 11.2.3 Measurement and requirements . 27 12 Mechanical requirements . 29 12

27、.1 General . 29 12.2 Mounting . 29 12.3 Compatibility between fuse-holder and fuse-link . 29 IEC 60127-6:2014 IEC 2014 3 12.4 Mechanical strength of the connection between fuse-base and fuse-carrier 30 12.4.1 Screw and bayonet connections 30 12.4.2 Plug-in connection . 30 12.5 Impact test 31 12.6 Me

28、chanical strength of the fuse-holder fastening on panels 31 12.6.1 Fixing nut fastening . 31 12.6.2 Fixing screw fastening . 31 12.6.3 Snap-in fastening 32 12.7 Terminals of fuse-bases 33 12.7.1 Terminals with screw-type clamping or screwless-type clamping . 33 12.7.2 Terminals for soldering 33 12.7

29、.3 Quick-connect male tab terminals 35 12.7.4 Quick-connect male tab terminals combined with solder tag terminals . 36 12.8 Resistance to vibration . 36 12.8.1 General . 36 12.8.2 Mounting . 36 12.8.3 Measurement and requirements . 37 13 Thermal requirements 37 13.1 Rated power acceptance test 37 13

30、.1.1 General . 37 13.1.2 Mounting . 37 13.1.3 Dummy fuse-links 38 13.1.4 Measurement of maximum allowable temperatures on fuse-holders . 40 13.1.5 Correlation between ambient air temperature TA1 and the power acceptance of a fuse-holder . 42 13.1.6 Temperature measuring point for ambient air tempera

31、ture T A143 13.1.7 Test method 43 13.2 Resistance to abnormal heat and fire 44 13.2.1 Needle-flame test 44 13.2.2 Glow-wire ignition test . 45 14 Endurance . 45 14.1 General . 45 14.2 Endurance test 45 14.3 Requirements . 45 15 Additional requirements . 45 15.1 Resistance to rusting 45 15.2 Resistan

32、ce to cleaning solvents 46 Annex A (normative) Test PC board for fuse-holders of rated currents up to 10 A . 47 Annex B (normative) Type tests, test sequences and number of samples 48 Annex C (informative) Insulation coordination 49 C.1 Overvoltage categories . 49 C.2 Degrees of pollution in the mic

33、ro-environment 49 C.3 Comparative tracking index CTI 50 Annex D (informative) Additional tests and requirements . 51 D.1 General . 51 D.2 Resistance to shock 51 D.2.1 General . 51 D.2.2 Mounting . 51 4 IEC 60127-6:2014 IEC 2014 D.2.3 Measurement and requirements . 51 D.3 Verification of the degree o

34、f protection of enclosures 51 D.4 Climatic category 52 D.4.1 General . 52 D.4.2 Test conditions and requirements 52 Annex E (informative) Information for the correct application of the fuse-holder . 53 Bibliography 54 Figure 1 Outline of gauges and dummy fuse-links according to IEC 60127-2 17 Figure

35、 2 Outline of gauges and dummy fuse-links according to IEC 60127-3 standard sheet 1 . 19 Figure 3 Outline of gauges and dummy fuse-links according to IEC 60127-3 standard sheets 3 and 4 . 19 Figure 4 Panel mounting 25 Figure 5 PC board mounting 25 Figure 6 Test device for mechanical test 29 Figure 7

36、 Fuse-holder fastening on panels 32 Figure 8 Tensile force test . 36 Figure 9 Compressive force test 36 Figure 10 Test device 38 Figure 11 Illustration of temperatures experienced in practice 41 Figure 12 Example of a derating curve . 44 Figure A.1 Example of a test board 47 Table 1 Features of unex

37、posed or exposed fuse-holders . 9 Table 2 Values for standard ratings and classifications 16 Table 3 Dimensions and materials for gauges according to IEC 60127-2 . 18 Table 4 Dimensions and materials for dummy fuse-links according to IEC 60127-2 . 18 Table 5 Dimensions and materials for gauges accor

38、ding to IEC 60127-3 20 Table 6 Dimensions and materials for dummy fuse-links according to IEC 60127-3 . 20 Table 7 Types of insulation between different live parts and accessible parts 21 Table 8 Required impulse withstand voltage for clearances . 22 Table 9 Overvoltage category II . 23 Table 10 Ove

39、rvoltage category III 23 Table 11 Minimum creepage distances in millimetres for a micro- environmentdependent on rated voltage, pollution degree, insulating material,corresponding to IEC 60664-1:2007, Table F.4 24 Table 12 Values for insulation resistance, dielectric strength and impulse withstand v

40、oltage 28 Table 13 Values for torque and axial pull . 30 Table 14 Torque values . 31 Table 15 Torque values . 32 Table 16 Mounting groups 33 Table 17 Cross-sections of conductors 34 Table 18 Tensile and compressive forces 36 IEC 60127-6:2014 IEC 2014 5 Table 19 Dummy fuse-links according to IEC 6012

41、7-2 . 39 Table 20 Dummy fuse-links according to IEC 60127-3 . 40 Table 21 Maximum allowable temperatures 42 Table A.1 Copper layer for test board 47 Table B.1 Type tests, test sequences and number of samples . 48 Table D.1 Examples of climatic categories . 52 Table E.1 Information for the correct ap

42、plication of the fuse-holder 53 6 IEC 60127-6:2014 IEC 2014 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ MINIATURE FUSES Part 6: Fuse-holders for miniature fuse-links FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all nationa

43、l electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical S

44、pecifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. Inte

45、rnational, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The f

46、ormal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations

47、 for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user

48、. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication s

49、hall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of