IEC 60079-18-2014 Explosive atmospheres - Part 18 Equipment protection by encapsulation m 《爆炸性环境.第18部分 密封 m 型设备保护》.pdf

《IEC 60079-18-2014 Explosive atmospheres - Part 18 Equipment protection by encapsulation m 《爆炸性环境.第18部分 密封 m 型设备保护》.pdf》由会员分享，可在线阅读，更多相关《IEC 60079-18-2014 Explosive atmospheres - Part 18 Equipment protection by encapsulation m 《爆炸性环境.第18部分 密封 m 型设备保护》.pdf（114页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 60079-18 Edition 4.0 2014-12 REDLINE VERSION Explosive atmospheres Part 18: Equipment protection by encapsulation “m” IEC 60079-18:2014-12 RLV(en) colour inside THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2014 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no pa

2、rt of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyr

3、ight or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerla

4、nd www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept und

5、er constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. IEC Catalogue - webstore.iec.ch/catalogue The stand-alone application for consulting the entire bibliographical information on IEC International Standards, Techni

6、cal Specifications, Technical Reports and other documents. Available for PC, Mac OS, Android Tablets and iPad. IEC publications search - www.iec.ch/searchpub The advanced search enables to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives in

7、formation on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available online and also once a month by email. Electropedia - www.electropedia.org The w

8、orlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms in 14 additional languages. Also known as the International Electrotechnical Vocabulary (IEV) online. IEC Glossary - std.iec.ch/glossary M

9、ore than 55 000 electrotechnical terminology entries in English and French extracted from the Terms and Definitions clause of IEC publications issued since 2002. Some entries have been collected from earlier publications of IEC TC 37, 77, 86 and CISPR. IEC Customer Service Centre - webstore.iec.ch/c

10、sc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. IEC 60079-18 Edition 4.0 2014-12REDLINE VERSIONExplosive atmospheres Part 18: Equipment protection by encapsulation “m” INTERNATIONAL ELECTROTECHNICAL COMMIS

11、SION RM ICS 29.260.20 PRICE CODE ISBN 978-2-8322-2078-8 Registered trademark of the International Electrotechnical Commission Warning! Make sure that you obtained this publication from an authorized distributor. colour inside 2 IEC 60079-18:2014 RLV IEC 2014 CONTENTS FOREWORD . 5 1 Scope 8 2 Normati

12、ve references. 8 3 Terms and definitions 9 4 General . 11 4.1 Level of protection (equipment protection level (EPL) 11 4.2 Additional requirements for levels of protection “ma” and “mb” . 11 4.3 Additional requirements for level of protection “ma” 11 4.4 Rated voltage and prospective short circuit c

13、urrent 11 5 Requirements for compounds . 11 5.1 General . 11 5.2 Specification . 12 5.3 Properties of the compound . 12 5.3.1 Water absorption 12 5.3.2 Dielectric strength 12 6 Temperatures 12 6.1 General . 12 6.2 Determination of the limiting temperatures . 13 6.2.1 Maximum surface temperature . 13

14、 6.2.2 Temperature of the compound 13 6.3 Temperature limitation . 13 7 Constructional requirements 13 7.1 General . 13 7.2 Determination of faults 14 7.2.1 Fault examination . 14 7.2.2 Components considered as not subject to fail . 14 7.2.3 Isolating components . 15 7.2.4 Infallible separation dist

15、ances 15 7.3 Free space in the encapsulation 17 7.3.1 Group III “m” equipment . 17 7.3.2 Group I and Group II “m” equipment . 17 7.4 Thickness of the compound . 18 7.4.1 “m” equipment 18 7.4.2 Windings for electrical machines 20 7.4.3 Rigid, multi-layer printed wiring boards with through connections

16、 20 7.5 Switching contacts 22 7.5.1 General . 22 7.5.2 Level of protection “ma” . 22 7.5.3 Level of protection “mb” . 23 7.5.4 Level of protection “mc” 23 7.6 External connections . 23 7.6.1 General . 23 7.6.2 Additional requirements for “ma” equipment 23 7.7 Protection of bare live parts . 23 IEC 6

17、0079-18:2014 RLV IEC 2014 3 7.8 Cells and batteries 24 7.8.1 General . 24 7.8.2 Prevention of gassing . 24 7.8.3 Protection against inadmissible temperatures and damage to the cells or batteries . 24 7.8.4. Reverse current . 25 7.8.5 Current limitation . 25 7.8.6 Protection against the polarity inve

18、rsion and deep discharge of the cells . 25 7.8.7 Charging of cells or batteries 26 7.8.8 Requirements for control safety devices for cells or batteries 26 7.9 Protective devices . 26 7.9.1 General . 26 7.9.2 Electrical protective devices . 27 7.9.3 Thermal protective devices . 28 7.9.4 Built-in prot

19、ective devices 28 8 Type tests . 29 8.1 Tests on the compound . 29 8.1.1 Water absorption test . 29 8.1.2 Dielectric strength test . 29 8.2 Tests on the apparatus 29 8.2.1 Test sequence . 29 8.2.2 Maximum temperature 29 8.2.3 Thermal endurance test 30 8.2.4 Dielectric strength test . 30 8.2.5 Cable

20、pull test 31 8.2.6 Pressure test for Group I and Group II electrical equipment 32 8.2.7 Test for resettable thermal protective device . 32 8.2.8 Sealing test for built-in protective devices . 33 9 Routine verifications and tests . 33 9.1 Visual inspections . 33 9.2 Dielectric strength test 33 10 Mar

21、king . 34 Annex A (informative) Basic requirements for compounds for “m” equipment . 35 Annex B (normative informative) Allocation of test samples . 36 Bibliography . 37 Figure 1 Dimensional key for thickness through the compound 19 Figure 2 Minimum distances for multi-layer printed wiring boards 22

22、 Figure 3 Fitting of blocking diodes 25 Figure A.1 Basic requirements for compounds for “m” equipment 35 Table 1 Distances through the compound . 16 Table 2 Minimum thickness of compound adjacent to free space for Group III “m” equipment 17 Table 3 Minimum thickness of compound adjacent to free spac

23、e for Group I and Group II “m” equipment . 18 Table 4 Thickness of the compound . 20 4 IEC 60079-18:2014 RLV IEC 2014 Table 5 Minimum distances for multi-layer printed wiring boards . 21 Table 6 Test pressure 32 Table B.1 Allocation of test samples . 36 IEC 60079-18:2014 RLV IEC 2014 5 INTERNATIONAL

24、 ELECTROTECHNICAL COMMISSION _ EXPLOSIVE ATMOSPHERES Part 18: Equipment protection by encapsulation “m” FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The o

25、bject of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifica

26、tions (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations li

27、aising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters expr

28、ess, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Commit

29、tees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC Nationa

30、l Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does no

31、t provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have t

32、he latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoeve

33、r, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publication

34、s is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. DISCLAIMER This Redline

35、 version is not an official IEC Standard and is intended only to provide the user with an indication of what changes have been made to the previous version. Only the current version of the standard is to be considered the official document. This Redline version provides you with a quick and easy way

36、 to compare all the changes between this standard and its previous edition. A vertical bar appears in the margin wherever a change has been made. Additions and deletions are displayed in red, with deletions being struck through. 6 IEC 60079-18:2014 RLV IEC 2014 Standard IEC 60079-18 has been prepare

37、d by IEC technical committee 31: Equipment for explosive atmospheres. This fourth edition cancels and replaces the third edition of IEC 60079-18 (2009), and constitutes a technical revision. This International Standard is to be used in conjunction with IEC 60079-0, Explosive atmospheres Part 0: Equi

38、pment-General requirements. This edition includes the following significant technical changes with respect to the previous edition: Type Explanation of the significance of the changes Clause Minor and editorial changes Extension Major technical changes Definitions deleted and moved to IEC 60079-0 3

39、X Heading modified /added to clarify which requirements are additional requirements for “ma” level of protection only 4 X Thermal conductivity added 5.2 X Note added that it is not a requirement of this standard that conformity to the manufacturers specification of the compound needs to be verified

40、5.3.2 X Clarification added 6.2.2 X Clarification added 7.1 X For the determination of faults options added and clarification given 7.2 X Additional information included in Figure 1 7.4.1 X “Varnish and similar coatings are not considered to be solid insulation.” was added in this section and delete

41、d in the definition on 3.8 7.4.2 X For rigid, multi-layer printed wiring boards with through connections additional standards added 7.4.3.1 X Protection against inadmissible temperatures and damage to the cells 7.8.3 C1 Electrical protective devices clarified and additional possibilities added 7.9.2

42、 X Thermal protective devices clarified and additional possibilities added 7.9.3 X 2/3 voltage limitation deleted 7.9.3 X Determination of the maximum temperature for “Da” fixed 8.2.2 C2 Stabilization of the temperature 8.2.2 C3 Thermal endurance to heat 8.2.3.1 X Temperature fixed as reference serv

43、ice temperatures and tests given as alternatives 8.2.3.1.1 X For the dielectric strength test procedure alternative possibilities added 8.2.4.1 X Alternative test methods for the required pressure test for Group I and Group II electrical equipment added 8.2.6 X Sealing test for build-in protective d

44、evices 8.2.8 X For the dielectric strength test procedure alternative possibilities added 9.2 X Marking 10 X X IEC 60079-18:2014 RLV IEC 2014 7 Explanation of the Types of Significant Changes: A) Definitions 1. Minor and editorial changes: Clarification Decrease of technical requirements Minor techn

45、ical change Editorial corrections These are changes which modify requirements in an editorial or a minor technical way. They include changes of the wording to clarify technical requirements without any technical change, or a reduction in level of existing requirement. 2. Extension: Addition of techn

46、ical options These are changes which add new or modify existing technical requirements, in a way that new options are given, but without increasing requirements for equipment that was fully compliant with the previous standard. Therefore, these will not have to be considered for products in conformi

47、ty with the preceding edition. 3. Major technical changes: addition of technical requirements increase of technical requirements These are changes to technical requirements (addition, increase of the level or removal) made in a way that a product in conformity with the preceding edition will not alw

48、ays be able to fulfil the requirements given in the later edition. These changes have to be considered for products in conformity with the preceding edition. For these changes additional information is provided in item B) below. Note These changes represent current technological knowledge. However,

49、these changes should not normally have an influence on equipment already placed on the market. B) Information about the background of Major technical changes C1 Clause 7.8.3 modified and additional requirements added for cells or batteries C2 The flexibility given in IEC 60079-0 is replaced by a min. requirement. For level of protection “ma” equipment, designed for EPL “Da” the maximum surface temperature shall be determined with the equipment mounted in accordance with the manufacturer