IEC 60068-2-78-2012 Environmental testing - Part 2-78 Tests - Test Cab Damp heat steady state《环境试验.第2-78部分 试验.试验箱 湿热、稳态》.pdf

《IEC 60068-2-78-2012 Environmental testing - Part 2-78 Tests - Test Cab Damp heat steady state《环境试验.第2-78部分 试验.试验箱 湿热、稳态》.pdf》由会员分享，可在线阅读，更多相关《IEC 60068-2-78-2012 Environmental testing - Part 2-78 Tests - Test Cab Damp heat steady state《环境试验.第2-78部分 试验.试验箱 湿热、稳态》.pdf（36页珍藏版）》请在麦多课文档分享上搜索。

1、 S+ IEC 60068-2-78 Edition 2.0 2012-10 IEC STANDARDS+ Environmental testing Part 2-78: Tests Test Cab: Damp heat, steady state Essais denvironnement Partie 2-78: Essais Essai Cab: Chaleur humide, essai continu S+ IEC 60068-2-78:2012 BASIC SAFETY PUBLICATION PUBLICATION FONDAMENTALE DE SCURIT colour

2、inside THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2012 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permi

3、ssion in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for

4、 further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou d

5、u Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office Tel

6、.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and r

7、elated technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Useful links: IEC publications search - www.iec.ch/searchpub The

8、advanced search enables you to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Ju

9、st Published details all new publications released. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent t

10、erms in additional languages. Also known as the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. A propos

11、de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de

12、la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub La recherche avance vous permet de trouver des publications CEI en utilisant diffrents critr

13、es (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications de la CEI. Just Published dtaille les nouvelles publications parues

14、. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues a

15、dditionnelles. Egalement appel Vocabulaire Electrotechnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. S+ IEC 60068-2-78 Edition 2.0 2012-10 IEC STANDAR

16、DS+ Environmental testing Part 2-78: Tests Test Cab: Damp heat, steady state Essais denvironnement Partie 2-78: Essais Essai Cab: Chaleur humide, essai continu INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE RL ICS 19.040; 29.020 PRICE CODE CODE PRIX ISBN 978-2-8

17、3220-444-3 BASIC SAFETY PUBLICATION PUBLICATION FONDAMENTALE DE SCURIT Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention!

18、Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. colour inside IEC 60068-2-78 Edition 2.0 2012-10 INTERNATIONAL STANDARD NORME INTERNATIONALE Environmental testing Part 2-78: Tests Test Cab: Damp heat, steady state Essais denvironnement Partie 2-78: Essais Essai

19、Cab: Chaleur humide, essai continu IEC 60068-2-78:2012 BASIC SAFETY PUBLICATION PUBLICATION FONDAMENTALE DE SCURIT 2 60068-2-78 IEC:2012 CONTENTS FOREWORD . 3 INTRODUCTION . 5 1 Scope and object 6 2 Normative references . 6 3 Terms and definitions . 6 4 General test procedure . 6 Test chamber and me

20、asuring system 6 4.1Severity . 7 4.2Pre-conditioning 7 4.3Testing procedure . 7 4.4Recovery procedure 8 4.5 5 Measurements 8 Initial measurements . 8 5.1Intermediate measurements 8 5.2Final measurements 8 5.3 6 Information to be given in the relevant specification 8 7 Information to be given in the

21、test report 9 Table 1 Temperature and relative humidity 7 60068-2-78 IEC:2012 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ ENVIRONMENTAL TESTING Part 2-78: Tests Test Cab: Damp heat, steady state FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standar

22、dization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes Inter

23、national Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate

24、 in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between

25、the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications h

26、ave the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any mi

27、sinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding nat

28、ional or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services

29、 carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC Nationa

30、l Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is d

31、rawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall n

32、ot be held responsible for identifying any or all such patent rights. International Standard IEC 60068-2-78 has been prepared by technical committee 104: Environmental conditions, classification, and methods of test. This second edition cancels and replaced the first edition, published in 2001 and c

33、onstitutes a technical revision. This edition includes editorial and format changes with respect to the previous edition: The test chamber from IEC 60068-3-6 has been introduced. 4 60068-2-78 IEC:2012 The text of this standard is based on the following documents: FDIS Report on voting 104/582/FDIS 1

34、04/588/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. It has the status of a basic safety publication in accordance with IEC G

35、uide 104. A list of all the parts in the IEC 60068 series, under the general title Environmental testing, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstor

36、e.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. 60068-2-78 IEC:2012 5 INTRODUCTION This part of IEC 60068 provides a test method of high humidity at constant temperature without conden

37、sation on the specimen over a prescribed period. This test is performed to evaluate the specimen as it is influenced by the absorption and diffusion of moisture and moisture vapour. 6 60068-2-78 IEC:2012 ENVIRONMENTAL TESTING Part 2-78: Tests Test Cab: Damp heat, steady state 1 Scope and object This

38、 part of IEC 60068 establishes a test method for determining the ability of components or equipment to withstand transportation, storage and use under conditions of high humidity. The object of this standard is to investigate the effect of high humidity at constant temperature without condensation o

39、n a specimen over a prescribed period. It is applicable to small equipment or components as well as large equipment, and can be applied to both heat-dissipating and non-heat-dissipating specimens. 2 Normative references The following documents, in whole or in part, are normatively referenced in this

40、 document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60068-1, Environmental testing Part 1:General and guidance IEC 60068-3-6, Environme

41、ntal testing Part 3-6: Supporting documentation and guidance Confirmation of the performance of temperature and humidity chambers IEC Guide 104, The preparation of safety publications and the use of basic safety publications and group safety publications 3 Terms and definitions None. 4 General test

42、procedure Test chamber and measuring system 4.1 The temperature and humidity chamber shall be constructed and verified in accordance with specifications IEC 60068-3-6. The chamber and measuring system shall be such that sensing devices can be located in the working space to monitor the temperature a

43、nd humidity, NOTE For heat-dissipating specimens, the temperature and humidity near the specimen may be influenced by the effect of heat dissipation from the specimen. condensed water is drained from the chamber and not re-used unless purified, no condensed water from the walls and roof of the test

44、chamber can fall on the specimen(s), 60068-2-78 IEC:2012 7 water utilized to maintain humidity levels has electrical conductivity of not more than 20 S/cm, the specimen under test shall not be subjected to radiant heat from the chamber conditioning devices, injected moisture, when applicable, is inj

45、ected remotely from the specimen and without being directly on it, the volume of the test chamber is at least five times the total volume of the specimen under test, a mounting device, when used, has minimum influence on the heat and humidity exchanges between specimen and surrounding conditions, un

46、less otherwise specified in the relevant specification. Severity 4.2 The test severity is defined by a combination of temperature, relative humidity (RH) and total test duration. Unless otherwise specified in the relevant specification, temperature and RH severities may be selected from the followin

47、g: Table 1 Temperature and relative humidity Temperature C Relative humidity % RH 30 2 93 3 30 2 85 3 40 2 93 3 40 2 85 3 Preferred test durations are: 12 h, 16 h, 24 h; 2 days, 4 days, 10 days, 21 days or 56 days. The total temperature tolerance of 2 K is intended to take account of absolute errors

48、 in the measurement, slow changes of temperature and temperature variations of the working space. However, in order to maintain the RH within the required tolerances, it is necessary to keep the temperature difference between any two points in the working space at any moment within narrower limits.

49、The required humidity conditions will not be achieved if such temperature differences exceed 1 K. It may also be necessary to keep short-term fluctuations within 0,5 K to maintain the required humidity. Pre-conditioning 4.3 The relevant specification may call for pre-conditioning. Testing procedure 4.4 The specimen shall be introduced into the chamber as required by the re